2W3671 INDICATOR-TEMPERATURE Caterpillar parts
3208, 3304, 3306, 3408, 3412, 3508, 3512, 3516
Rating:
Alternative (cross code) number:
CA2W3671
2W-3671
2W3671
CA2W3671
2W-3671
2W3671
Weight: 0.50 pounds 0 kg.
GEN SET ENGINE, MARINE ENGINE,
Compatible equipment models: 2W3671:
Number on catalog scheme:
17
For full view, you need register
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00539829
Loosen adjusting screws (3). This will prevent a bent valve or a bent pushrod during the installation of the rocker shaft assembly. Install pushrods (2) and ensure that the pushrods are seated in the valve lifters.
Install rocker shaft assembly (1) in position on the cylinder head.
Ensure that the dowels on each end of the rocker shaft assembly are in alignment with the holes in the cylinder head.
Illustration 2 g00591852
3304B torque sequence
Illustration 3 g00544706
3306B torque sequence
Note: Replace the O-ring seal when the bolt toward the rear of the engine is installed in the rocker shaft support.
Apply 6V-4876 Lubricant on the threads of six bolts (4) except for the bolt that passes through the rear rocker shaft support (bolt (6) in Illustration 3). Install six bolts (4) in the rocker shaft assembly.
Refer to Illustration 3. Tighten six bolts (4) for the rocker shaft, as follows:
Tighten all the bolts in the numerical sequence to a torque of 155 N m (115 lb ft).
Tighten all the bolts in the numerical sequence to a torque of 250 17 N m (185 13 lb ft).
Tighten all the bolts again in the numerical sequence to a final torque of 250 17 N m (185 13 lb ft).
The assembled length of the springs at both ends of the rocker shaft must be 1.50 0.25 mm (.059 .010 inch). Remove the washers or install the washers behind the springs to change the assembled length of the springs.
Adjust the inlet valve lash to 0.38 0.08 mm (.015 .003 inch) and adjust the exhaust valve lash to 0.64 0.08 mm (.025 .003 inch). Refer to Testing and Adjusting, "Air Inlet and Exhaust System" for more information on setting the valve lash. Tighten the locknuts for the adjusting screws (3) to a torque of 29 7 N m (21 5 lb ft). Refer to Specifications, "Valve Rocker Arms and Lifters".End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00539829
Loosen adjusting screws (3). This will prevent a bent valve or a bent pushrod during the installation of the rocker shaft assembly. Install pushrods (2) and ensure that the pushrods are seated in the valve lifters.
Install rocker shaft assembly (1) in position on the cylinder head.
Ensure that the dowels on each end of the rocker shaft assembly are in alignment with the holes in the cylinder head.
Illustration 2 g00591852
3304B torque sequence
Illustration 3 g00544706
3306B torque sequence
Note: Replace the O-ring seal when the bolt toward the rear of the engine is installed in the rocker shaft support.
Apply 6V-4876 Lubricant on the threads of six bolts (4) except for the bolt that passes through the rear rocker shaft support (bolt (6) in Illustration 3). Install six bolts (4) in the rocker shaft assembly.
Refer to Illustration 3. Tighten six bolts (4) for the rocker shaft, as follows:
Tighten all the bolts in the numerical sequence to a torque of 155 N m (115 lb ft).
Tighten all the bolts in the numerical sequence to a torque of 250 17 N m (185 13 lb ft).
Tighten all the bolts again in the numerical sequence to a final torque of 250 17 N m (185 13 lb ft).
The assembled length of the springs at both ends of the rocker shaft must be 1.50 0.25 mm (.059 .010 inch). Remove the washers or install the washers behind the springs to change the assembled length of the springs.
Adjust the inlet valve lash to 0.38 0.08 mm (.015 .003 inch) and adjust the exhaust valve lash to 0.64 0.08 mm (.025 .003 inch). Refer to Testing and Adjusting, "Air Inlet and Exhaust System" for more information on setting the valve lash. Tighten the locknuts for the adjusting screws (3) to a torque of 29 7 N m (21 5 lb ft). Refer to Specifications, "Valve Rocker Arms and Lifters".End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Caterpillar parts catalog:
Parts indicator Caterpillar catalog:
3126, 3176B, 3176C, 3196, 3208, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3408, 3408B, 3408C, 3412, 3412C, 3412E, 3508, 3512, 3516, C18, C27, C9, CB-534, D398, PR-750B, SS-250
120G, 14G, 16G, 3176B, 3176C, 3196, 3208, 3306, 3406B, 3408, 3412, 3508, 3512, 3516, C-10, C-12, C12, SUF557
120, 120B, 120G, 12E, 12G, 130G, 140, 140B, 140G, 14E, 16, 16G, 215, 225, 3304, 3306, 518, 528, 561B, 561C, 561D, 571G, 572G, 583K, 594, 594H, 621, 621B, 623, 627, 627B, 631C, 633D, 637, 637B, 637D, 6...
3304, 3306
3306, 3406, 3412, D7F
3208, 3304, 3306, 3406, 3408, 3412, 3508, 3512, 3516, D320A, D342C, D348, FB221, G3304, SR4
3304, 3304B, 3306, 3306B, 3406, 3406B, 3408, 3412, 3412E, G3406, G399
3304, 3306, 3408, 3412, 3508, 3512, 3516
14E, 16G, 215, 225, 235, 245, 3304, 3306, 3406, 3408, 3412, 561C, 583K, 621, 621B, 623, 627, 633D, 637B, 637D, 815, 816, 920, 930, 941, 950, 951B, 955K, 955L, 966C, 977H, 977K, 980, 980B, 983, D343, D...
3406, 3406B, 3408, 3412, 583K, 594H, D348, D353C, D379, D379B, D398, D398B, D399, D8K
3406, 3408, 3412, 641B
3304, 3306, 3508, 3512, 3516, G399
3306, 3406, 3412, D7F
3304, 3306
3304, 3306, 3406, 3412, D348, D353C
120, 120B, 120G, 12E, 12G, 130G, 140, 140B, 140G, 14E, 16, 16G, 215, 225, 3304, 3306, 518, 528, 561B, 561C, 561D, 571G, 572G, 583K, 594, 594H, 621, 621B, 623, 627, 627B, 631C, 633D, 637, 637B, 637D, 6...
4W2620
INDICATOR-FUEL LEVEL
416, 428, 436, 446, AP-1000, AP-1050, AP-800
416, 428, 436, 446, AP-1000, AP-1050, AP-800
4W2621
INDICATOR
416, 428, 436, 446
416, 428, 436, 446
416, 428, 436, 446, 65, 75, AP-1000, AP-1050, AP-800
3114, 3116, 3126, 416, 428, 436, 446
7T5180
INDICATOR
416, 426, 428, 446, 918F, D7H, D8N, IT18F
416, 426, 428, 446, 918F, D7H, D8N, IT18F
2W3675
INDICATOR-TEMPERATURE
3304, 3306, 3408, 3412, 3508, 3512, 3516
3304, 3306, 3408, 3412, 3508, 3512, 3516