INDICATOR AS 4W0379 - Caterpillar

4W0379 INDICATOR AS Caterpillar parts 3606, 3608, 3612, 3616, C175-16, C175-20, C280-12, C280-16, C280-6, C280-8, G3606, G3606B, G3608, G3612, G3616

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4W0379
4W-0379
4W0379

Weight: 0.40 pounds 0 kg.

Buy INDICATOR AS 4W0379 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE, PETROLEUM ENGINE,

This part in 4 request: Show. This information for suppliers only!

2024-12-09

2023-05-19

2023-05-17

2021-07-04

Compatible equipment models: 4W0379:

GAS ENGINE G3606 G3606B G3608 G3612 G3616

GENERATOR SET C175-16 C175-20

MARINE AUXILIARY 3608

MARINE ENGINE 3606 3608 3612 3616 C175-16 C280-12 C280-16 C280-6 C280-8

PETROLEUM ENGINE C175-16 Caterpillar

Number on catalog scheme: 7

Caterpillar 4W0379 Parts scheme INDICATOR AS

For full view, you need register

Information:

Pull battery cable (27) through the battery box and connect to the battery inside the battery box. Connect wire harness (28) at the connector.
Illustration 9 g00697695
Connect wire harness (25) and (26) at the connectors.
Illustration 10 g00697694
Check the O-ring seal for wear. If necessary, replace the O-ring seal. Connect the seven hydraulic hose assemblies (24) .
Illustration 11 g00697692
Install floorplate (23). Install ten bolts and washers (22) .
Illustration 12 g00697691
Install cushion (20) and barrier (21) on the cab floor.
Illustration 13 g00697688
Illustration 14 g00697683
Install front floormat (19) on the cab. Install the left side retaining plate (16) on the left side of the cab floor. Install the two screws for the retaining plate (15). Install right side retaining plate (18) on the right side of the cab floor. Install the two screws for the retaining plate (17) .
Illustration 15 g00697681
Position the governor control cable (13). Install the nut and tighten nut (14). Install the cotter pin and linkage pin (12) on the end of the governor control cable (13) .
Illustration 16 g00697679
Position + battery cable (11) and install two tie straps (8). Connect the ground strap and ground wires (10) and install bolt (9) .
Illustration 17 g00697645
Install cover (7) and install two bolts and washers (6) .
Illustration 18 g00697491
Note: Install all sheet metal.
Illustration 19 g00697496
Check seals for wear or damage. If necessary, replace the seals. Connect the two air conditioning lines (4) and (5). The lines are located at the bottom left side corner of the cab. Refer to the Service Manual, SENR3334, "Air Conditioning And Heating Service Manual" for charging the air conditioning system .
Illustration 20 g00697469
Illustration 21 g00697473
Install all the tie straps (3) that hold the heater hose assemblies (1) and (2) to the machine. There is a total of six tie straps.
Illustration 22 g00697465
Install the heater hose assemblies (1) and (2). Turn the heater hose valves to the open position. Release the safety lock and lower the hood.
Install the sheet metal that was removed in order to remove the cab.
If the machine is equipped with auxiliary fuel tanks, fill both of the tanks.Note: Refer to the Operation and Maintenance Manual, SEBU6753, "Lubricant Viscosities and Refill Capacities".