10R3261 INJECTOR GP-FUEL Caterpillar parts
C15
Rating:
Alternative (cross code) number:
CA10R3261
10R-3261
10R3261
CA10R3261
10R-3261
10R3261
Weight: 5 pounds 2 kg.
TRUCK ENGINE,
Related part:
2490702
INJECTOR GP-FUEL
10R3261
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
1pcs 10R-3261 244-7702 249-0702 Fuel Injector Suitable for Caterpillar CAT Engine C15
TuneCrumph Including:1*Fuel Injector || Part Number:249-0702, 2490702, CA2490702, 244-7702 || Fits for Caterpillar CAT Engine C15 || Attention: Dear buyers, precise matching of auto parts is the prerequisite for safe installation! To avoid the problems such as returns, exchanges or installation hazards caused by incorrect model selection, please carefully read and verify the model before placing your order. Thank you for your support! || NOTE:We are fully aware that your satisfaction is the driving force for the growth of our brand. Thank you for giving us the opportunity to serve you. If there is anything we haven't covered, please give us your feedback directly. Your suggestions are extremely precious to us!
TuneCrumph Including:1*Fuel Injector || Part Number:249-0702, 2490702, CA2490702, 244-7702 || Fits for Caterpillar CAT Engine C15 || Attention: Dear buyers, precise matching of auto parts is the prerequisite for safe installation! To avoid the problems such as returns, exchanges or installation hazards caused by incorrect model selection, please carefully read and verify the model before placing your order. Thank you for your support! || NOTE:We are fully aware that your satisfaction is the driving force for the growth of our brand. Thank you for giving us the opportunity to serve you. If there is anything we haven't covered, please give us your feedback directly. Your suggestions are extremely precious to us!
1pcs 10R-3261 244-7702 249-0702 Fuel Injector Suitable for Caterpillar CAT Engine C15
OfkZynodor Including:1*Fuel Injector || Part Number:249-0702, 2490702, CA2490702, 244-7702 || Fits for Caterpillar CAT Engine C15 || Please make sure to carefully compare the photos and check the part numbers before making the purchase. If you are unable to confirm your engine model or part number, please leave us a message and we will assist you in confirming that the product you purchase is the one you need. || Your order is not merely a single purchase but the beginning of a cooperative journey, aiming to ensure the safe and smooth operation of your vehicle. We are proud to offer you reliable precision engineering components and unparalleled services.
OfkZynodor Including:1*Fuel Injector || Part Number:249-0702, 2490702, CA2490702, 244-7702 || Fits for Caterpillar CAT Engine C15 || Please make sure to carefully compare the photos and check the part numbers before making the purchase. If you are unable to confirm your engine model or part number, please leave us a message and we will assist you in confirming that the product you purchase is the one you need. || Your order is not merely a single purchase but the beginning of a cooperative journey, aiming to ensure the safe and smooth operation of your vehicle. We are proud to offer you reliable precision engineering components and unparalleled services.
1PCS Common Rail Fuel Injectors 10R-3261 Fits for Caterpillar CAT 395 637K 657G 6015 6015 FS Excavators C18 Engine
EXKATCC Product Name:Common Rail Fuel Injectors || Replaces Number:10R-3261 || Application:Fits for Caterpillar CAT 395 637K 657G 6015 6015 FS Excavators C18 Engine || Tips: Before purchasing, please carefully confirm whether the part number and compatible machine model match. || Notice: Our product is air freight express, striving to shorten the downtime of customer equipment
EXKATCC Product Name:Common Rail Fuel Injectors || Replaces Number:10R-3261 || Application:Fits for Caterpillar CAT 395 637K 657G 6015 6015 FS Excavators C18 Engine || Tips: Before purchasing, please carefully confirm whether the part number and compatible machine model match. || Notice: Our product is air freight express, striving to shorten the downtime of customer equipment
For full view, you need register
Compatible equipment models: 10R3261:
Information:
Remove & Install Wire Connectors And Contacts
Typical Example1. With the rear of wire connector toward you, snap tool (A) (the correct size for the wire being removed) over the wire of the contact to be removed.2. Slide tool (A) along the wire into the contact cavity until it engages the contact and resistance is felt. Do not twist or insert tool (A) at an angle.
Typical Example3. Pull contact (2) and wire assembly out of connector (1).4. Remove the damaged contact from the wire.
Typical Example5. Use tool (B) and the following procedure to secure contact (2) to the wire.a. Strip 6.3 mm (.25 in.) insulation from the wire.b. Raise selector knob (3) and rotate until arrow is aligned with the wire size to be crimped.c. Loosen locknut. Turn adjusting screw (4) in (clockwise) until it stops.
Typical Exampled. Insert contact (2) into tool (B). Turn the adjusting screw out (counter clockwise) until the contact is flush with indentor cover (5) on tool (B). Tighten locknut.
Typical Examplec. Insert wire in contact (2). The contact must be centered between the indentors. Close the handles until the handle contacts the stop.d. Release the handles and remove the crimped contact.e. Inspect the contact to insure that all wire strands are inside the crimp barrel. Look in the hole in the contact. If the crimp is correct wire strands will be visable in the hole in the contact.
Typical Example6. Grasp the wire approximately 25.4 mm (1.00 in.) behind the contact crimp barrel.7. Hold connector (1) with the rear grommet facing you.8. Push contact (2) straight into connector (1) until a positive stop is felt.9. Gently pull on the wire and connector assembly to confirm that the contact is properly locked in place.
Typical Example1. With the rear of wire connector toward you, snap tool (A) (the correct size for the wire being removed) over the wire of the contact to be removed.2. Slide tool (A) along the wire into the contact cavity until it engages the contact and resistance is felt. Do not twist or insert tool (A) at an angle.
Typical Example3. Pull contact (2) and wire assembly out of connector (1).4. Remove the damaged contact from the wire.
Typical Example5. Use tool (B) and the following procedure to secure contact (2) to the wire.a. Strip 6.3 mm (.25 in.) insulation from the wire.b. Raise selector knob (3) and rotate until arrow is aligned with the wire size to be crimped.c. Loosen locknut. Turn adjusting screw (4) in (clockwise) until it stops.
Typical Exampled. Insert contact (2) into tool (B). Turn the adjusting screw out (counter clockwise) until the contact is flush with indentor cover (5) on tool (B). Tighten locknut.
Typical Examplec. Insert wire in contact (2). The contact must be centered between the indentors. Close the handles until the handle contacts the stop.d. Release the handles and remove the crimped contact.e. Inspect the contact to insure that all wire strands are inside the crimp barrel. Look in the hole in the contact. If the crimp is correct wire strands will be visable in the hole in the contact.
Typical Example6. Grasp the wire approximately 25.4 mm (1.00 in.) behind the contact crimp barrel.7. Hold connector (1) with the rear grommet facing you.8. Push contact (2) straight into connector (1) until a positive stop is felt.9. Gently pull on the wire and connector assembly to confirm that the contact is properly locked in place.
Caterpillar parts catalog:
Parts injector Caterpillar catalog:
385C, 385C FS, 385C L, 631G, 637G, 834H, 836H, 986H, 988H, C15, CX31-C15I, D9T, TH35-C15I
365C, 365C L, 583T, 621G, 623G, 627G, 657E, 657G, 735, 740, 770, 824H, 825H, 826H, 980H, AD30, C15, CX31-C15I, D8R, D8T, R2900G, TH35-C15I
535C, 545C, C7
120K, 120K 2, 12K, 140G, 140K, 140K 2, 140M, 160K, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 525C, 535C, 545C, 57...
2625341
INJECTOR GP-FUEL
C15, TH35-C15T
C15, TH35-C15T
