1563895 INJECTOR GP-FUEL Caterpillar parts
3412E
Rating:
Alternative (cross code) number:
CA1563895
156-3895
1563895
CA1563895
156-3895
1563895
MARINE ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$50.26
03 Jun 2021
US: EFI Equipment a
ADJUSTER SET - SEAT FOR HYSTER: 1563895
Parts Express HYSTER || All Brand new & rebuilt items comes with 1 year warranty. || ADJUSTER SET - SEAT. Category: HYSTER FORKLIFT PARTS. This part can also be found under the following part numbers: HY1563895 1563895 Â HYSTER 1563895 Â HYSTER1563895 1563895 Â Â . All Brand new & rebuilt items comes with 1 year warranty.
Parts Express HYSTER || All Brand new & rebuilt items comes with 1 year warranty. || ADJUSTER SET - SEAT. Category: HYSTER FORKLIFT PARTS. This part can also be found under the following part numbers: HY1563895 1563895 Â HYSTER 1563895 Â HYSTER1563895 1563895 Â Â . All Brand new & rebuilt items comes with 1 year warranty.
Number on catalog scheme:
4
For full view, you need register
Compatible equipment models: 1563895:
Information:
Adjustment of Pump Output Flow (Constant Horsepower Control)
Illustration 1 g01186772
Main pump compartment (20) Adjustment screw (21) Locknut (22) Adjustment screw (23) Locknut (24) Adjustment screw (25) Locknut (26) Adjustment screw (27) LocknutAdjust the flow of the drive pump for the first stage of the constant horsepower control. The idler pump must be at no-load condition.
Loosen locknut (23) .
Turn adjustment screw (22) in order to adjust the output flow of the pump. Turning adjustment screw (22) clockwise will increase the output flow of the pump. Turning adjustment screw (22) counterclockwise will decrease the output flow of the pump. A 1/4 turn of adjustment screw (22) will change the output flow of the pump at the following pressure.
Output flow of the pump will change approximately 23 L/min (6.1 US gpm) if the output flow is adjusted in the pressure range of 11800 kPa (1700 psi) to 19600 kPa (2850 psi). The pump is operating in the first stage of the constant horsepower control.
Tighten locknut (23) to a torque of 98 9.8 N m (70 7 lb ft).Adjust the flow of the drive pump for the second stage of the constant horsepower control. The idler pump must be at no-load condition.
Loosen locknut (21) .
Turn adjustment screw (20) in order to adjust the output flow of the pump. Turning adjustment screw (20) clockwise will increase the output flow of the pump. Turning adjustment screw (20) counterclockwise will decrease the output flow of the pump. A 1/4 turn of adjustment screw (20) will change the output flow of the pump at the following pressure.
Output flow of the pump will change approximately 9 L/min (2.4 US gpm) if the output flow is adjusted in the pressure range of 27500 kPa (4000 psi) to 34300 kPa (4950 psi). The pump is operating in the second stage of the constant horsepower control.
Tighten locknut (20) to a torque of 28 7 N m (21 5 lb ft).Adjust the idler pump in the same manner as the drive pump. Use locknut (27) and adjustment screw (26) in order to adjust the first stage of the constant horsepower control. Use locknut (25) and adjustment screw (24) in order to adjust the second stage of the constant horsepower control.Adjustment of the Maximum Output Flow of the Pump
Illustration 2 g01186773
Main pump compartment (28) Adjustment screw (29) Locknut (30) Locknut (31) Adjustment screwAdjust the maximum output flow of the drive pump.
Loosen locknut (30) .
In order to adjust maximum output flow, turn adjustment screw (31) . Turning adjustment screw (31) clockwise will decrease the maximum output flow of the pump. Turning adjustment screw (31) counterclockwise will increase the maximum output flow of the pump. A 1/4 turn of adjustment screw (31) will change the maximum output flow approximately 5 L/min (1.3 US gpm).
Tighten locknut (30) to a torque of 177 15 N m (130 11 lb ft).Adjust the maximum output flow of the idler pump in the same manner as the drive pump. Use locknut (29) and adjustment screw
Illustration 1 g01186772
Main pump compartment (20) Adjustment screw (21) Locknut (22) Adjustment screw (23) Locknut (24) Adjustment screw (25) Locknut (26) Adjustment screw (27) LocknutAdjust the flow of the drive pump for the first stage of the constant horsepower control. The idler pump must be at no-load condition.
Loosen locknut (23) .
Turn adjustment screw (22) in order to adjust the output flow of the pump. Turning adjustment screw (22) clockwise will increase the output flow of the pump. Turning adjustment screw (22) counterclockwise will decrease the output flow of the pump. A 1/4 turn of adjustment screw (22) will change the output flow of the pump at the following pressure.
Output flow of the pump will change approximately 23 L/min (6.1 US gpm) if the output flow is adjusted in the pressure range of 11800 kPa (1700 psi) to 19600 kPa (2850 psi). The pump is operating in the first stage of the constant horsepower control.
Tighten locknut (23) to a torque of 98 9.8 N m (70 7 lb ft).Adjust the flow of the drive pump for the second stage of the constant horsepower control. The idler pump must be at no-load condition.
Loosen locknut (21) .
Turn adjustment screw (20) in order to adjust the output flow of the pump. Turning adjustment screw (20) clockwise will increase the output flow of the pump. Turning adjustment screw (20) counterclockwise will decrease the output flow of the pump. A 1/4 turn of adjustment screw (20) will change the output flow of the pump at the following pressure.
Output flow of the pump will change approximately 9 L/min (2.4 US gpm) if the output flow is adjusted in the pressure range of 27500 kPa (4000 psi) to 34300 kPa (4950 psi). The pump is operating in the second stage of the constant horsepower control.
Tighten locknut (20) to a torque of 28 7 N m (21 5 lb ft).Adjust the idler pump in the same manner as the drive pump. Use locknut (27) and adjustment screw (26) in order to adjust the first stage of the constant horsepower control. Use locknut (25) and adjustment screw (24) in order to adjust the second stage of the constant horsepower control.Adjustment of the Maximum Output Flow of the Pump
Illustration 2 g01186773
Main pump compartment (28) Adjustment screw (29) Locknut (30) Locknut (31) Adjustment screwAdjust the maximum output flow of the drive pump.
Loosen locknut (30) .
In order to adjust maximum output flow, turn adjustment screw (31) . Turning adjustment screw (31) clockwise will decrease the maximum output flow of the pump. Turning adjustment screw (31) counterclockwise will increase the maximum output flow of the pump. A 1/4 turn of adjustment screw (31) will change the maximum output flow approximately 5 L/min (1.3 US gpm).
Tighten locknut (30) to a torque of 177 15 N m (130 11 lb ft).Adjust the maximum output flow of the idler pump in the same manner as the drive pump. Use locknut (29) and adjustment screw
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts injector Caterpillar catalog:
3412E
3412E
3412E
1536295
INJECTOR GP-FUEL
3412E
3412E
3412E
3412E
3508B, 3512B, 3516B, PM3508, PM3512, PM3516, PP3516
3126B
3126B, 3126E
3512B, 3516B
345B II, 365B L
3508, 3508B, 3512, 3512B, 3512C, 3516B, 3516C, 854G, 992G, PM3508, PM3512, PM3516
3126, 3126B, 3126E
3412E