2123464 INJECTOR GP-FUEL Caterpillar parts
3176C, 3196
Rating:
Alternative (cross code) number:
CA2123464
212-3464
2123464
CA2123464
212-3464
2123464
Weight: 4 pounds 2 kg.
INDUSTRIAL ENGINE, MARINE ENGINE,
Related part:
2123464
INJECTOR GP-FUEL
10R0725
R
You can buy:
US$702.60
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Diesel Common Rail Injector 212-3464 2123464 Compatible For Carter Pule C10
Liaeyou Controls the fuel injection volume to ensure the engine runs stably. || Atomizes the fuel to promote full combustion and improve fuel efficiency. || Maintains the balance of in the engine cylinder. || Helps the engine start smoothly in different temperature conditions. || Reduces fuel and lowers emissions.
Liaeyou Controls the fuel injection volume to ensure the engine runs stably. || Atomizes the fuel to promote full combustion and improve fuel efficiency. || Maintains the balance of in the engine cylinder. || Helps the engine start smoothly in different temperature conditions. || Reduces fuel and lowers emissions.
Z-Ryixiu 2pcs Wheel Liner Front Left Driver Right Passenger Side Plastic for Ford for Fusion Hybrid/S/SE/SEL/Sport 2010-2012 212-3464
Z-Ryixiu Fitment:for Ford,for Fusion Hybrid/S/SE/SEL/Sport 2010-2012 || Components: (2) Wheel Liners || Material:Plastic || Part Number:FO1248143,10959164,AE5Z16103B,FO1249143,AE5Z16102B || Easy to Install:Keeps Factory Ducting for Brakes or Fluid Coolers || Quantity Sold:Set of 2 || Part Name:Wheel Liner || Built Standard: Care to Meet Industry Standards for Quality Control, Ensuring Reliable and Consistent Performance
Z-Ryixiu Fitment:for Ford,for Fusion Hybrid/S/SE/SEL/Sport 2010-2012 || Components: (2) Wheel Liners || Material:Plastic || Part Number:FO1248143,10959164,AE5Z16103B,FO1249143,AE5Z16102B || Easy to Install:Keeps Factory Ducting for Brakes or Fluid Coolers || Quantity Sold:Set of 2 || Part Name:Wheel Liner || Built Standard: Care to Meet Industry Standards for Quality Control, Ensuring Reliable and Consistent Performance
OKJHFD 2pcs Wheel Liner Front Left Driver Right Passenger Side Plastic for Ford for Fusion Hybrid/S/SE/SEL/Sport 2010-2012 212-3464
OKJHFD Fitment:for Ford,for Fusion Hybrid/S/SE/SEL/Sport 2010-2012 || Components: (2) Wheel Liners || Material:Plastic || Part Number:FO1248143,10959164,AE5Z16103B,FO1249143,AE5Z16102B || Easy to Install:Keeps Factory Ducting for Brakes or Fluid Coolers || Quantity Sold:Set of 2 || Part Name:Wheel Liner || Built Standard: Care to Meet Industry Standards for Quality Control, Ensuring Reliable and Consistent Performance
OKJHFD Fitment:for Ford,for Fusion Hybrid/S/SE/SEL/Sport 2010-2012 || Components: (2) Wheel Liners || Material:Plastic || Part Number:FO1248143,10959164,AE5Z16103B,FO1249143,AE5Z16102B || Easy to Install:Keeps Factory Ducting for Brakes or Fluid Coolers || Quantity Sold:Set of 2 || Part Name:Wheel Liner || Built Standard: Care to Meet Industry Standards for Quality Control, Ensuring Reliable and Consistent Performance
This part in 2 request:
Show.
This information for suppliers only!
2021-05-04
2017-04-10
Number on catalog scheme:
4
For full view, you need register
Information:
Removal Procedure
Start By:
Install the engine lifting brackets. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01283374Note: Mark the positions of the engine supports and the shims for proper installation. The right side engine supports are connected to the plates on the generator base by dowels. The dowels must be removed before the mounting supports can be removed.
Remove the plastic caps from the engine supports to the access hole for the dowels. Use a 1/2 inch bolt with a washer in order to remove the dowels, if necessary.
Attach a suitable lifting device to the engine lifting brackets. The weight of the 3606 Engine is approximately 15700 kg (34600 lb). The weight of the 3608 Engine is approximately 19000 kg (41900 lb).
Remove bolts (1) that hold engine supports (2) to the generator base. Check the O-ring seals on the bolts for damage. If necessary, replace the O-ring seals. The O-ring seals should be installed on clean bolts.
Lift the engine enough in order to place a suitable lifting device around engine support (2). Use the forcing bolt in order to help lift the engine. The weight of each engine support (2) is approximately 60 kg (130 lb).
Remove the shims, if necessary.
Remove bolts (3) that hold engine support (2) to the cylinder block.
Tap engine support (2) with a rubber mallet in order to loosen dowels (4) from the cylinder block.
Remove engine support (2) from the side of the cylinder block.
If necessary, remove dowels (4) from engine support (2). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01283374
If dowels (4) were removed from engine support (2), install the dowels. The dowels must extend 20.0 1.0 mm (0.79 0.04 inch) above the surface of engine support (2). Check the O-ring seals for damage. If necessary, replace the O-ring seals.
Use a suitable lifting device to place engine support (2) in position on the side of the cylinder block. The weight of each engine support (2) is approximately 60 kg (130 lb). Install bolts (3). Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Install the shims in the original location, if necessary.
Install the dowels through engine support (2) and into the base on the right side of the engine, if necessary.
Lower the engine onto the base assembly. The weight of the 3606 Engine is approximately 15700 kg (34600 lb). The weight of the 3608 Engine is approximately 19000 kg (41900 lb). Remove the forcing bolt when you lower the engine. Install bolts (1).
Check the alignment between the engine and the driven equipment.
Perform the following check for soft foot:
Soft foot is measured with a dial indicator. Mount a dial indicator from the base assembly to the top of the foot next to the engine block. Be sure that all the jacking screws are loose. While one foot at a time is loosened, the
Start By:
Install the engine lifting brackets. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01283374Note: Mark the positions of the engine supports and the shims for proper installation. The right side engine supports are connected to the plates on the generator base by dowels. The dowels must be removed before the mounting supports can be removed.
Remove the plastic caps from the engine supports to the access hole for the dowels. Use a 1/2 inch bolt with a washer in order to remove the dowels, if necessary.
Attach a suitable lifting device to the engine lifting brackets. The weight of the 3606 Engine is approximately 15700 kg (34600 lb). The weight of the 3608 Engine is approximately 19000 kg (41900 lb).
Remove bolts (1) that hold engine supports (2) to the generator base. Check the O-ring seals on the bolts for damage. If necessary, replace the O-ring seals. The O-ring seals should be installed on clean bolts.
Lift the engine enough in order to place a suitable lifting device around engine support (2). Use the forcing bolt in order to help lift the engine. The weight of each engine support (2) is approximately 60 kg (130 lb).
Remove the shims, if necessary.
Remove bolts (3) that hold engine support (2) to the cylinder block.
Tap engine support (2) with a rubber mallet in order to loosen dowels (4) from the cylinder block.
Remove engine support (2) from the side of the cylinder block.
If necessary, remove dowels (4) from engine support (2). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01283374
If dowels (4) were removed from engine support (2), install the dowels. The dowels must extend 20.0 1.0 mm (0.79 0.04 inch) above the surface of engine support (2). Check the O-ring seals for damage. If necessary, replace the O-ring seals.
Use a suitable lifting device to place engine support (2) in position on the side of the cylinder block. The weight of each engine support (2) is approximately 60 kg (130 lb). Install bolts (3). Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Install the shims in the original location, if necessary.
Install the dowels through engine support (2) and into the base on the right side of the engine, if necessary.
Lower the engine onto the base assembly. The weight of the 3606 Engine is approximately 15700 kg (34600 lb). The weight of the 3608 Engine is approximately 19000 kg (41900 lb). Remove the forcing bolt when you lower the engine. Install bolts (1).
Check the alignment between the engine and the driven equipment.
Perform the following check for soft foot:
Soft foot is measured with a dial indicator. Mount a dial indicator from the base assembly to the top of the foot next to the engine block. Be sure that all the jacking screws are loose. While one foot at a time is loosened, the
Caterpillar parts catalog:
Parts injector Caterpillar catalog:
3176C, 345B II, 345B II MH, 365B, 365B L, 725, 730, C-10, C-12, R1600, R1700G, W345B II
3176C, 3196, 480, 65E, 75D, 75E, 85E, 95E, C-10
3196, C-12, C12
3196, C-12, C12
3406E
3406E, 3456, C-18
3406E, 3456, PM3456
3508B, 3512B
2290196
INJECTOR GP-FUEL
3508B, 3512, 3512B, 3516B, SPF343, SPS343, SPT343
3508B, 3512, 3512B, 3516B, SPF343, SPS343, SPT343
1536295
INJECTOR GP-FUEL
3412E
3412E
3412E
3176C
2776572
INJECTOR GP-FUEL
3508B, 3508C, 3516, 3516B, 3516C
3508B, 3508C, 3516, 3516B, 3516C
3508, 3508B, 3512, 3512B, 3512C, 3516B
3508, 3508B, 3512B, 3516B