3647040 INJECTOR GP-FUEL Caterpillar parts
Rating:
Alternative (cross code) number:
CA3647040
364-7040
3647040
CA3647040
364-7040
3647040
Weight: 0.37 pounds 0 kg.
You can buy:
US$93.65
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Diesel Fuel Injector LJBB05901B 3647040 T408845 Injection Nozzle Compatible With Parkins
Generic Accurate control of fuel injection quantity: Inject an appropriate amount of fuel into the cylinder accurately according to the engine's operating conditions, improving fuel utilization and combustion efficiency || Improving combustion quality: making fuel atomization finer and more thoroughly mixed with air, thereby optimizing the combustion process, reducing pollutant emissions, and improving engine power performance || Material: Corrosion-resistant brass/stainless steel body construction. || Quality: Undergoes strict factory testing for reliable performance. || Installation: OEM-spec fit; professional installation recommended
Generic Accurate control of fuel injection quantity: Inject an appropriate amount of fuel into the cylinder accurately according to the engine's operating conditions, improving fuel utilization and combustion efficiency || Improving combustion quality: making fuel atomization finer and more thoroughly mixed with air, thereby optimizing the combustion process, reducing pollutant emissions, and improving engine power performance || Material: Corrosion-resistant brass/stainless steel body construction. || Quality: Undergoes strict factory testing for reliable performance. || Installation: OEM-spec fit; professional installation recommended
Number on catalog scheme:
12
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
1/2 inch - UNF by 4 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01336671
Typical example
Always wear protective gloves when handling parts that have been heated.
If the flywheel ring gear was removed, follow Step 1.a through Step 1.c in order to install ring gear (5) to flywheel (1).
Identify the orientation of teeth (6) on new ring gear (5). Note: The chamfered side of ring gear teeth (6) must face toward the starting motor when the flywheel is installed. The chamfered side of ring gear teeth ensures the correct engagement of the starting motor.
Heat flywheel ring gear (5) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (5) is correct and quickly install the ring gear onto flywheel (1).
Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the correct procedure.
Illustration 2 g01336668
Typical example
Install a suitable lifting device onto flywheel (1). The flywheel can weigh 71 kg (156 lb).
Install Tooling (A) in Position (X) on the crankshaft.
Use the lifting device to position flywheel (1) onto Tooling (A).
If necessary, install pilot bearing (3) and bolts (2) to flywheel (1).
Install bolts (4) to flywheel (1).
Remove Tooling (A) and install remaining bolts (4) to flywheel (1).
Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) and (4) to a torque of 140 N m (103 lb ft).
Remove the lifting device from flywheel (1).
Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further information. End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
1/2 inch - UNF by 4 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01336671
Typical example
Always wear protective gloves when handling parts that have been heated.
If the flywheel ring gear was removed, follow Step 1.a through Step 1.c in order to install ring gear (5) to flywheel (1).
Identify the orientation of teeth (6) on new ring gear (5). Note: The chamfered side of ring gear teeth (6) must face toward the starting motor when the flywheel is installed. The chamfered side of ring gear teeth ensures the correct engagement of the starting motor.
Heat flywheel ring gear (5) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (5) is correct and quickly install the ring gear onto flywheel (1).
Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the correct procedure.
Illustration 2 g01336668
Typical example
Install a suitable lifting device onto flywheel (1). The flywheel can weigh 71 kg (156 lb).
Install Tooling (A) in Position (X) on the crankshaft.
Use the lifting device to position flywheel (1) onto Tooling (A).
If necessary, install pilot bearing (3) and bolts (2) to flywheel (1).
Install bolts (4) to flywheel (1).
Remove Tooling (A) and install remaining bolts (4) to flywheel (1).
Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) and (4) to a torque of 140 N m (103 lb ft).
Remove the lifting device from flywheel (1).
Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further information. End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Caterpillar parts catalog:
Parts injector Caterpillar catalog:
3622210
INJECTOR GP-FUEL
Caterpillar
Caterpillar
Caterpillar
5571200
INJECTOR
Caterpillar
Caterpillar
5297864
INJECTOR GP-FUEL
Caterpillar
Caterpillar
4694201
INJECTOR AS-FUEL
Caterpillar
Caterpillar
Caterpillar
4336864
INJECTOR GP-FUEL
Caterpillar
Caterpillar
4317296
INJECTOR GP-FUEL
Caterpillar
Caterpillar
4161510
INJECTOR GP-FUEL
Caterpillar
Caterpillar
3851524
INJECTOR GP-FUEL
Caterpillar
Caterpillar
3829074
INJECTOR & MTG GP-DEF
Caterpillar
Caterpillar
3829040
INJECTOR GP-DIESEL EXH FLUID
Caterpillar
Caterpillar