4563546 INJECTOR GP- Caterpillar parts
Rating:
Alternative (cross code) number:
CA4563546
456-3546
4563546
CA4563546
456-3546
4563546
Weight: 1 pounds 0 kg.
Related part:
4563546
INJECTOR GP-F -G
20R5080
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Fuel Injector 456-3546 20R-5080 4563546 20R5080 for Caterpillar CAT C9 Engine
MGADOSIA Part Number: 456-3546 20R-5080 4563546 20R5080 || Applicable models: Fit for Caterpillar CAT C9 Engine || Safety: 100% Tested Before Shipping to Ensure Product Safety, Stability and Durability. || Function: High-quality material for long-lasting durability. Perfect match for the original car and easy to install || TIPS: Please be sure to compare carefully with photos and check part number before buying items, If you are not sure this part is suitable, please feel free to contact us, we'll reply you as soon as possible.
MGADOSIA Part Number: 456-3546 20R-5080 4563546 20R5080 || Applicable models: Fit for Caterpillar CAT C9 Engine || Safety: 100% Tested Before Shipping to Ensure Product Safety, Stability and Durability. || Function: High-quality material for long-lasting durability. Perfect match for the original car and easy to install || TIPS: Please be sure to compare carefully with photos and check part number before buying items, If you are not sure this part is suitable, please feel free to contact us, we'll reply you as soon as possible.
Number on catalog scheme:
For full view, you need register
Information:
2. Remove the screen and magnets.
Do not drop or rap the magnets against anything. Replace any damaged magnets.
3. Wash the screen and magnets in clean, nonflammable solvent. Clean the magnets with a cloth, stiff brush or pressure air.4. Install the magnets.5. Install the screen.6. Inspect the spring and seal. Replace them if damaged.7. Install the cover and floor plate.8. Start and run the engine at LOW IDLE. 9. Open the right side access door. 10. Maintain the oil level between the ADD and FULL marks on dipstick (1).11. Remove oil filler cap (2) to add oil if necessary.12. Install the cap and close access door.Belts - Alternator and Fan
Inspect/Replace/Adjust
1. Replace the belts if cracked, frayed or cut.2. Replace the belts in sets, even if only one belt is damaged. 3. Measure the deflection of the belt. Apply approximately 110 N (25 lb) force midway between the drive pulley and the alternator.Deflection should be 14 to 20 mm (.56 to .81 in).4. Adjust the belt if the deflection is not correct. 5. Loosen mounting bolt (1) and position locking bolt (2).6. Move the alternator to tighten belt.7. Tighten all of the bolts.8. Measure the belt's deflection. If the deflection is not correct, repeat the adjustment procedure.Fan Pulley Bearing
Lubricate
The fitting is located on the right side of the engine. Lubricate the fitting.Brakes
Check Brake Pedals
Adjust the brakes when the pedal travel measures 152 mm (6 in).To Adjust
1. Remove the guard. 2. Remove the cover. 3. Turn the adjusting screw to the right until tight.4. Turn the screw out 21/2 rotations (9 clicks of the detent noise).5. Install the cover and guard.Tracks
Adjust
Grease is under high pressure.Pressurized grease coming out of the relief valve can penetrate your body causing injury or death.Do not watch the relief valve to see if grease is escaping. Watch the track or track adjustment cylinder to see if the track is being loosened.Loosen the relief valve one turn only.
Move the machine forward at least twice the length of the machine. Allow the machine to coast to a stop. Do not apply the brakes to stop the machine.With the machine stopped on level ground: push the flywheel clutch lever forward to disengage the clutch; pull the knob to engage the parking brake lock; move the transmission speed selector to NEUTRAL; move the forward-neutral-reverse directional lever to NEUTRAL; lower all attachments and apply a slight pressure.Tracks should be adjusted under the same conditions in which the machine is used. If packing conditions prevail on the job, the tracks should be adjusted with packing present.
Do not attempt to tighten track when dimension (X) is within 3 mm (.12 in). Contact your Caterpillar dealer for track service or instructions.
1. Remove adjusting valve cover plate (1).2. Add grease (MPGM) through adjusting valve (2) until track is tight.3. Make a mark on the roller frame 13 mm (.50 in) behind the idler bearing support. Be sure there is space for the front idler to retract.4. Allow the idler to move back by opening the
Do not drop or rap the magnets against anything. Replace any damaged magnets.
3. Wash the screen and magnets in clean, nonflammable solvent. Clean the magnets with a cloth, stiff brush or pressure air.4. Install the magnets.5. Install the screen.6. Inspect the spring and seal. Replace them if damaged.7. Install the cover and floor plate.8. Start and run the engine at LOW IDLE. 9. Open the right side access door. 10. Maintain the oil level between the ADD and FULL marks on dipstick (1).11. Remove oil filler cap (2) to add oil if necessary.12. Install the cap and close access door.Belts - Alternator and Fan
Inspect/Replace/Adjust
1. Replace the belts if cracked, frayed or cut.2. Replace the belts in sets, even if only one belt is damaged. 3. Measure the deflection of the belt. Apply approximately 110 N (25 lb) force midway between the drive pulley and the alternator.Deflection should be 14 to 20 mm (.56 to .81 in).4. Adjust the belt if the deflection is not correct. 5. Loosen mounting bolt (1) and position locking bolt (2).6. Move the alternator to tighten belt.7. Tighten all of the bolts.8. Measure the belt's deflection. If the deflection is not correct, repeat the adjustment procedure.Fan Pulley Bearing
Lubricate
The fitting is located on the right side of the engine. Lubricate the fitting.Brakes
Check Brake Pedals
Adjust the brakes when the pedal travel measures 152 mm (6 in).To Adjust
1. Remove the guard. 2. Remove the cover. 3. Turn the adjusting screw to the right until tight.4. Turn the screw out 21/2 rotations (9 clicks of the detent noise).5. Install the cover and guard.Tracks
Adjust
Grease is under high pressure.Pressurized grease coming out of the relief valve can penetrate your body causing injury or death.Do not watch the relief valve to see if grease is escaping. Watch the track or track adjustment cylinder to see if the track is being loosened.Loosen the relief valve one turn only.
Move the machine forward at least twice the length of the machine. Allow the machine to coast to a stop. Do not apply the brakes to stop the machine.With the machine stopped on level ground: push the flywheel clutch lever forward to disengage the clutch; pull the knob to engage the parking brake lock; move the transmission speed selector to NEUTRAL; move the forward-neutral-reverse directional lever to NEUTRAL; lower all attachments and apply a slight pressure.Tracks should be adjusted under the same conditions in which the machine is used. If packing conditions prevail on the job, the tracks should be adjusted with packing present.
Do not attempt to tighten track when dimension (X) is within 3 mm (.12 in). Contact your Caterpillar dealer for track service or instructions.
1. Remove adjusting valve cover plate (1).2. Add grease (MPGM) through adjusting valve (2) until track is tight.3. Make a mark on the roller frame 13 mm (.50 in) behind the idler bearing support. Be sure there is space for the front idler to retract.4. Allow the idler to move back by opening the
Caterpillar SIS machinery equipment:
Parts injector Caterpillar catalog:
Caterpillar
Caterpillar
4537577
INJECTOR GP-
Caterpillar
Caterpillar
4502046
INJECTOR GP-GR
Caterpillar
Caterpillar
4502022
INJECTOR AS
Caterpillar
Caterpillar
4499166
INJECTOR GP-
Caterpillar
Caterpillar
4711845
INJECTOR AS
Caterpillar
Caterpillar
4697689
INJECTOR GP
Caterpillar
Caterpillar
Caterpillar
4579012
INJECTOR AS-
Caterpillar
Caterpillar
Caterpillar
Caterpillar