5S7218 INSERT INLAY Caterpillar parts
130G, 1673C, 3304, 3306, 561C, 627, 814, 941, 950, 955K, 955L, 966C, 977K, 980B, D4D, D5, D6C, D7F, D7G, G3304, G3306
Rating:
Alternative (cross code) number:
CA5S7218
5S-7218
5S7218
CA5S7218
5S-7218
5S7218
Weight: 0.010 pounds 0 kg.
GAS ENGINE, WHEEL SCRAPER,
Cross Reference:
CATERPILLAR
5S7218,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
5S7218 Pack of 6 VALVE INSERT INLET Suitable For Caterpillar® 5S7218
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
Number on catalog scheme:
13
For full view, you need register
Compatible equipment models: 5S7218:
Information:
Use this procedure in order to troubleshoot a problem with the fuel system. Probable Causes
Fuel pressure sensor
Fuel lines
Fuel transfer pump
Fuel return pressure regulatorRecommended Actions
Note: High fuel pressure may cause high fuel temperatures. Troubleshoot a code for high fuel pressure before troubleshooting a code for high fuel temperature.Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 1
Troubleshooting Test Steps Values Results
1. Active Codes and Logged Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM).
B. Monitor the diagnostic codes on Cat ET. Check for active or logged diagnostic codes. Specifically check for codes that could be associated to poor acceleration. Refer to the histogram information for engine derates in Cat ET.
Note: Wait at least 30 seconds in order for diagnostic codes to become active.
C. If the histograms contain derates and no diagnostic codes are present, then the engine is operating normally.
Diagnostic trouble code
Result: A diagnostic code is present.
Repair: Troubleshoot any codes before continuing with this procedure.
Verify that the repair eliminated the problem. Reset the histogram.
Result: A diagnostic code is not present.
Proceed to Test Step 2.
2. Check the Fuel Pressure Sensor
A. Record the fuel pressure from Cat ET.
Use a mechanical gauge to check the system fuel pressure. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
G. Record the fuel pressure on the pressure gauge.
Note: If a mechanical gauge is not available, determine if the fuel pressure reading on Cat ET is reasonable.
Fuel pressure
Result: The gauge value of the fuel pressure is reasonable when compared to the fuel pressure reading shown in ET.
Proceed to Test Step 3.
Result: The gauge value of the fuel pressure is not reasonable when compared to the fuel pressure reading shown in ET.
Repair: Replace the pressure sensor. Reset all active codes and clear all logged codes by cycling the keyswitch
Fuel pressure sensor
Fuel lines
Fuel transfer pump
Fuel return pressure regulatorRecommended Actions
Note: High fuel pressure may cause high fuel temperatures. Troubleshoot a code for high fuel pressure before troubleshooting a code for high fuel temperature.Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 1
Troubleshooting Test Steps Values Results
1. Active Codes and Logged Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM).
B. Monitor the diagnostic codes on Cat ET. Check for active or logged diagnostic codes. Specifically check for codes that could be associated to poor acceleration. Refer to the histogram information for engine derates in Cat ET.
Note: Wait at least 30 seconds in order for diagnostic codes to become active.
C. If the histograms contain derates and no diagnostic codes are present, then the engine is operating normally.
Diagnostic trouble code
Result: A diagnostic code is present.
Repair: Troubleshoot any codes before continuing with this procedure.
Verify that the repair eliminated the problem. Reset the histogram.
Result: A diagnostic code is not present.
Proceed to Test Step 2.
2. Check the Fuel Pressure Sensor
A. Record the fuel pressure from Cat ET.
Use a mechanical gauge to check the system fuel pressure. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
G. Record the fuel pressure on the pressure gauge.
Note: If a mechanical gauge is not available, determine if the fuel pressure reading on Cat ET is reasonable.
Fuel pressure
Result: The gauge value of the fuel pressure is reasonable when compared to the fuel pressure reading shown in ET.
Proceed to Test Step 3.
Result: The gauge value of the fuel pressure is not reasonable when compared to the fuel pressure reading shown in ET.
Repair: Replace the pressure sensor. Reset all active codes and clear all logged codes by cycling the keyswitch
Cat SIS web machinery list:
Parts insert Caterpillar catalog:
120B, 120G, 12G, 130G, 140B, 140G, 1673C, 215, 215B, 215C, 225, 235, 235B, 330 L, 3304, 3304B, 3306, 3306B, 330B, 518, 528, 572G, 621R, 637D, 815B, 930, 936F, 941, 950, 950B, 950B/950E, 955L, 963, 966...
143H, 14G, 1673C, 1674, 16G, 16H NA, 235, 235C, 3176B, 3208, 330, 330 L, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3408C, 3412, 3412C, 3412E, 350, 375, 375 L, 5080, 571G, 572G, 578, 583R, 589, 615C, 621R...
120G, 12G, 130G, 140G, 235, 235B, 330 L, 3304B, 330B, 528, 936F, 950B, 963, 966D, 966R, 973, 973C, D250B, D25C, D300B, D30C, D350C, D35C, D4E, D4E SR, D5H, D5H XL, D6D, D6G, D6H, D6H XL, D6H XR, D6R, ...
120G, 12G, 130G, 140B, 1673C, 3304, 3306, 561C, 621R, 627, 637D, 814, 941, 950, 955L, 966C, 977K, 980B, D4D, D5, D5B, D6C, D7G
12E, 1673, 1673B, 1676, 621, 641, 641B, 657, 657B, 666, 666B, 772, 773, 955H, 977H, 980, D330A, D333A, D333B, D336, D342C, D348, D349, D353C, D379, D379A, D379B, D398, D398A, D398B, D399, G3306, G3306...
12G, 3306, 528, 930, 950, 955K, D4D, G3304, G3306
120B, 140B, 1673C, 235, 3304, 3306, 930, 955L, D6D, D7F, D7G
G3304, G3304B, G3306, G3306B
120, 120B, 12F, 140, 140B, 14E, 16, 16G, 235, 235C, 245, 3304, 3304B, 3306, 3606, 3608, 5230, 5230B, 528, 528B, 530B, 561C, 561D, 572G, 578, 589, 594H, 613, 621, 621E, 621R, 623, 627, 631C, 633C, 637B...
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA
12G, 130G, 140G, 160G
120G, 12G, 130G, 14G
3435964
INSERT-VALVE SEAT
329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 930K, 938K, C4.4, C7.1
329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 930K, 938K, C4.4, C7.1
3224120
INSERT-VALVE SEAT
329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 930K, 938K, C4.4, C7.1
329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 930K, 938K, C4.4, C7.1
3647354
INSERT-FOAM
3516C
3516C
3647353
INSERT-FOAM
3516C
3516C
3647341
INSERT-FOAM
3516C
3516C
3647340
INSERT-FOAM
3516C
3516C
5L3777
INSERT
D346, D348, G379
D346, D348, G379
12E, 1673, 1673B, 1676, 621, 641, 641B, 657, 657B, 666, 666B, 772, 773, 955H, 977H, 980, D330A, D333A, D333B, D336, D342C, D348, D349, D353C, D379, D379A, D379B, D398, D398A, D398B, D399, G3306, G3306...
3306, 583H, 769, D333B, D334, D337F, D342, D342C
1674, 1676, 621, 980, D334, D336
1674, 1676, 621, 980, D334, D336
120G, 12G, 130G, 140B, 1673C, 3304, 3306, 561C, 621R, 627, 637D, 814, 941, 950, 955L, 966C, 977K, 980B, D4D, D5, D5B, D6C, D7G