9M3205 INSERT (Intake) Caterpillar parts
16, 1693, 631C, 641B, 650B, 651, 657, 657B, 666, 768B, 769, 772, 777, 824B, 825B, 826B, 834, 983, 988, 992, D10, D343, D346, D348, D349, G343
Rating:
Alternative (cross code) number:
CA9M3205
9M-3205
9M3205
CA9M3205
9M-3205
9M3205
Weight: 0.08 pounds 0 kg.
GAS ENGINE, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$10.03
20 Jan 2024
US: Florida-Parts-Z
5S6447 - Insert 9M3205 fits Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$14.26
10 Jan 2024
US: Florida-Parts-Z
9M3205 - Insert (Intake-Standard) 5S6447 for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$10.03
14 Jul 2023
US: Florida-Parts-Z
5S6447 - Insert 9M3205 fits Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Number on catalog scheme:
None
For full view, you need register
Compatible equipment models: 9M3205:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
1/2 inch - UNF by 4 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01336671
Typical example
Always wear protective gloves when handling parts that have been heated.
If the flywheel ring gear was removed, follow Step 1.a through Step 1.c in order to install ring gear (5) to flywheel (1).
Identify the orientation of teeth (6) on new ring gear (5). Note: The chamfered side of ring gear teeth (6) must face toward the starting motor when the flywheel is installed. The chamfered side of ring gear teeth ensures the correct engagement of the starting motor.
Heat flywheel ring gear (5) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (5) is correct and quickly install the ring gear onto flywheel (1).
Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the correct procedure.
Illustration 2 g01336668
Typical example
Install a suitable lifting device onto flywheel (1). The flywheel can weigh 71 kg (156 lb).
Install Tooling (A) in Position (X) on the crankshaft.
Use the lifting device to position flywheel (1) onto Tooling (A).
If necessary, install pilot bearing (3) and bolts (2) to flywheel (1).
Install bolts (4) to flywheel (1).
Remove Tooling (A) and install remaining bolts (4) to flywheel (1).
Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) and (4) to a torque of 140 N m (103 lb ft).
Remove the lifting device from flywheel (1).
Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further information. End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
1/2 inch - UNF by 4 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01336671
Typical example
Always wear protective gloves when handling parts that have been heated.
If the flywheel ring gear was removed, follow Step 1.a through Step 1.c in order to install ring gear (5) to flywheel (1).
Identify the orientation of teeth (6) on new ring gear (5). Note: The chamfered side of ring gear teeth (6) must face toward the starting motor when the flywheel is installed. The chamfered side of ring gear teeth ensures the correct engagement of the starting motor.
Heat flywheel ring gear (5) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (5) is correct and quickly install the ring gear onto flywheel (1).
Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the correct procedure.
Illustration 2 g01336668
Typical example
Install a suitable lifting device onto flywheel (1). The flywheel can weigh 71 kg (156 lb).
Install Tooling (A) in Position (X) on the crankshaft.
Use the lifting device to position flywheel (1) onto Tooling (A).
If necessary, install pilot bearing (3) and bolts (2) to flywheel (1).
Install bolts (4) to flywheel (1).
Remove Tooling (A) and install remaining bolts (4) to flywheel (1).
Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) and (4) to a torque of 140 N m (103 lb ft).
Remove the lifting device from flywheel (1).
Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further information. End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Cat SIS web machinery list:
Parts insert Caterpillar catalog:
16, 1693, 245, 3406, 3408, 3412, 631C, 637D, 641, 641B, 650B, 651E, 657B, 657E, 666, 768B, 769, 772, 777, 824B, 825B, 826B, 834, 980C, 983, 988, 988B, 992, 992C, D10, D343, D346, D348, D349
16, 1693, 245, 3406, 3408, 3412, 631C, 637D, 641B, 650B, 651E, 657, 657B, 657E, 666, 768B, 769, 772, 777, 824B, 825B, 826B, 834, 980C, 983, 988, 988B, 992, 992C, D10, D343, D346, D348, D349, G343
16, 1693, 245, 3406, 3408, 3412, 631C, 637D, 641B, 650B, 651E, 657, 657B, 657E, 666, 768B, 769, 772, 777, 824B, 825B, 826B, 834, 980C, 983, 988B, 992, 992C, D10, D343, D346, D348, D349, G343
16, 1693, 245, 3406, 3408, 3412, 631C, 637D, 641B, 650B, 651E, 657, 657B, 657E, 666, 768B, 769, 772, 777, 824B, 825B, 826B, 834, 980C, 983, 988, 988B, 992, 992C, D10, D343, D346, D348, D349
16, 1693, 245, 3406, 3408, 3412, 631C, 637D, 641B, 650B, 651E, 657, 657B, 657E, 666, 768B, 769, 772, 777, 824B, 825B, 826B, 834, 980C, 983, 988, 988B, 992, 992C, D10, D343, D346, D348, D349
3508, 3508B, 3512, 3512B, 3516, 3516B, 5130B, 5230B, 776D, 777, 777D, 785C, 789C, 793C, 854G, 992G, 994D, D11R
3508, 3508B, 3512, 3512B, 3516, 3516B, 5130B, 5230B, 776D, 777, 777D, 785C, 789C, 793C, 854G, 992G, 994D, D11R
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 793D, 797...
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 793D, 797...
12E, 1673, 1673B, 1676, 621, 641, 641B, 657, 657B, 666, 666B, 772, 773, 955H, 977H, 980, D330A, D333A, D333B, D336, D342C, D348, D349, D353C, D379, D379A, D379B, D398, D398A, D398B, D399, G3306, G3306...
120, 120B, 12F, 140, 140B, 14E, 16, 16G, 235, 235C, 245, 3304, 3304B, 3306, 3606, 3608, 5230, 5230B, 528, 528B, 530B, 561C, 561D, 572G, 578, 589, 594H, 613, 621, 621E, 621R, 623, 627, 631C, 633C, 637B...
10, 44, 6A, 7A, 824G II, 824H, 844, 844H, 844K, 854G, 854K, 8A, 9A, 9S, D10, D10N, D10R, D10T, D11N, D11R, D11T, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL, D7R, D8R, D8R...
16, 1693, 651, 657, 666, 769, 824, 824B, 834, 983, 988, 992, D343, D346, D348
D342, D342C, D8H, D8K, G342C
D342, D342C, D8H, D8K, G342C
5L3777
INSERT
D346, D348, G379
D346, D348, G379
12E, 1673, 1673B, 1676, 621, 641, 641B, 657, 657B, 666, 666B, 772, 773, 955H, 977H, 980, D330A, D333A, D333B, D336, D342C, D348, D349, D353C, D379, D379A, D379B, D398, D398A, D398B, D399, G3306, G3306...
3306, 583H, 769, D333B, D334, D337F, D342, D342C
1673B, 561B, 951B, 955K, 977H, 977K, D330A, D330B, D333B, D4D
12E, 1673, 1673B, 561B, 951B, 955H, 955K, 977H, 977K, D330A, D330B, D333A, D333B, D4D
12E, 1673, 1673B, 561B, 951B, 955H, 955K, 977H, 977K, D330A, D330B, D333A, D333B, D4D
12F, D348, D349, D379B, D398, D399, G398, G399
5L3776
INSERT
D346, D348, D349, D379B, D398, D399, G398, G399
D346, D348, D349, D379B, D398, D399, G398, G399
6L3105
INSERT
G379
G379