1U6436 INSTALLER AS-DUO-CONE SEAL Caterpillar parts
950G
Rating:
Alternative (cross code) number:
CA1U6436
1U-6436
1U6436
CA1U6436
1U-6436
1U6436
Weight: 1 pounds 0 kg.
WHEEL LOADER,
Compatible equipment models: 1U6436:
Number on catalog scheme:
None
For full view, you need register
Information:
ENGINES
ALL CATERPILLAR MACHINES POWERED BY 3306 ENGINES;
ALL 3306 AND 3306B INDUSTRIAL, MARINE AND GENERATOR SET ENGINESProblem:
There have been continuing reports of oil leaks past the 129-0357 Oil Pan Plate Gasket between the 3306 engine cylinder block and the 2P-1738 Plate Assembly. Solution:
Before installing a new 129-0357 Oil Pan Plate Gasket, be sure the contact surfaces are clean and dry. Also, apply 8T-9022 RTV Silicone (Blue) General Purpose Sealant sparingly at the "tee" joints at the front and rear housings. Additional improvement in bolt torque retention may be gained through the installation of steel back-up strips under the bolts that do not go through the oil pan. To install the back-up strips, one 9Y-0629 Plate, two 9Y-0630 Plates, eighteen 3B-1915 Bolts, and eighteen 5M-2894 Washers are required. Install the new components as shown in the illustration. Tighten the all of the bolts (oil pan bolts and oil pan plate bolts) to a torque of 60 10 N m (44 7 lb ft). After the engine has been run and reached normal operating temperature and then allowed to cool, the bolt torque should be checked. The bolts must not turn with a MINIMUM tightening torque of 26 N m (19 lb ft). If a bolt turns with less than the minimum tightening torque, retighten that bolt to a torque of 60 10 N m (44 7 lb ft).
Location of new 9Y-0629 Plate (1),two new 9Y-0630 Plates (2), eighteen new 3B-1915 Bolts (3),and eighteen 5M-2894 Washers (4) on typical 3306 engine oil pan and oil pan plate.COPYRIGHT 1999 CATERPILLAR ALL RIGHTS RESERVED
ALL CATERPILLAR MACHINES POWERED BY 3306 ENGINES;
ALL 3306 AND 3306B INDUSTRIAL, MARINE AND GENERATOR SET ENGINESProblem:
There have been continuing reports of oil leaks past the 129-0357 Oil Pan Plate Gasket between the 3306 engine cylinder block and the 2P-1738 Plate Assembly. Solution:
Before installing a new 129-0357 Oil Pan Plate Gasket, be sure the contact surfaces are clean and dry. Also, apply 8T-9022 RTV Silicone (Blue) General Purpose Sealant sparingly at the "tee" joints at the front and rear housings. Additional improvement in bolt torque retention may be gained through the installation of steel back-up strips under the bolts that do not go through the oil pan. To install the back-up strips, one 9Y-0629 Plate, two 9Y-0630 Plates, eighteen 3B-1915 Bolts, and eighteen 5M-2894 Washers are required. Install the new components as shown in the illustration. Tighten the all of the bolts (oil pan bolts and oil pan plate bolts) to a torque of 60 10 N m (44 7 lb ft). After the engine has been run and reached normal operating temperature and then allowed to cool, the bolt torque should be checked. The bolts must not turn with a MINIMUM tightening torque of 26 N m (19 lb ft). If a bolt turns with less than the minimum tightening torque, retighten that bolt to a torque of 60 10 N m (44 7 lb ft).
Location of new 9Y-0629 Plate (1),two new 9Y-0630 Plates (2), eighteen new 3B-1915 Bolts (3),and eighteen 5M-2894 Washers (4) on typical 3306 engine oil pan and oil pan plate.COPYRIGHT 1999 CATERPILLAR ALL RIGHTS RESERVED
Caterpillar parts catalog:
Parts installer Caterpillar catalog:
924F, IT24F
963B, 963C, 973, BG-2455C, D5E, D6D, D6E SR, D7R
D398, G399
1217702
INSTALLER-WEAR SLEEVE
3606, 3608, 3612, 3616, G3606, G3608, G3612, G3616
3606, 3608, 3612, 3616, G3606, G3608, G3612, G3616
772B, 775B
771C, 784B, AD40, AD45, AD45B, AD55, AD55B, AD60, AE40
784B, 789
2578474
INSTALLER GROUP
950H, 966H
950H, 966H
950G, D250E, D300D