2032567 INSULATION Caterpillar parts
Rating:
Alternative (cross code) number:
CA2032567
203-2567
2032567
CA2032567
203-2567
2032567
Information:
Parts Needed
Repair Procedure
1 Remove collets (1) and the bucket pins. Remove the bucket from the machine; see the Service Manual. 2 Lower the temperature of bearings (2) and install the bearings in the bucket at each pin location as shown. Install bearings (3) in each lift arm. Tighten bolts (4). See the chart on page 3 for the correct part numbers for your machine. 3 Put pin assembly (5) in position through bearings (2). Install block (6), two bolts (7) and plate (8) on pin (5) as shown. Tack weld block (6) in position on the bucket at approximately the location shown. Remove plate (8) and the bucket pin. Make a 10.0 (.39") fillet weld along sides (A), (B) and (C) of block (6). 4 Put the bucket in position on the lift arms and install pins (5), spacers (9) [992C only], plate (8) and bolts (7). Install grease fittings (10). Use multi-purpose grease as a lubricant in the pins. Install plug (11) in each bucket pin. On 992C, do not install the bucket until after steps 5 and 6, page 5 have been done. 5 On 992C machines, install upper pin bearings (12) in each side of the bucket. Install bearings (13) in the tilt links. Tighten bolts (14). 6 Put pins (15) in position through bearings (12). Assemble 8V914 Block (16), 8V915 Plate (17) and two 1J7370 Bolts on each pin (15). Tack weld blocks (16) to the bucket at approximately the location shown. Remove plate (17) and the pin and make a 10.0 (.39") fillet weld around blocks (16). Connect the bucket tilt links to the bucket with pins (15) and 8V1355 Spacers (18). Install 3B8491 Fitting (19) in each pin (5). Connect the lift arms to the bucket with a similar procedure.
Repair Procedure
1 Remove collets (1) and the bucket pins. Remove the bucket from the machine; see the Service Manual. 2 Lower the temperature of bearings (2) and install the bearings in the bucket at each pin location as shown. Install bearings (3) in each lift arm. Tighten bolts (4). See the chart on page 3 for the correct part numbers for your machine. 3 Put pin assembly (5) in position through bearings (2). Install block (6), two bolts (7) and plate (8) on pin (5) as shown. Tack weld block (6) in position on the bucket at approximately the location shown. Remove plate (8) and the bucket pin. Make a 10.0 (.39") fillet weld along sides (A), (B) and (C) of block (6). 4 Put the bucket in position on the lift arms and install pins (5), spacers (9) [992C only], plate (8) and bolts (7). Install grease fittings (10). Use multi-purpose grease as a lubricant in the pins. Install plug (11) in each bucket pin. On 992C, do not install the bucket until after steps 5 and 6, page 5 have been done. 5 On 992C machines, install upper pin bearings (12) in each side of the bucket. Install bearings (13) in the tilt links. Tighten bolts (14). 6 Put pins (15) in position through bearings (12). Assemble 8V914 Block (16), 8V915 Plate (17) and two 1J7370 Bolts on each pin (15). Tack weld blocks (16) to the bucket at approximately the location shown. Remove plate (17) and the pin and make a 10.0 (.39") fillet weld around blocks (16). Connect the bucket tilt links to the bucket with pins (15) and 8V1355 Spacers (18). Install 3B8491 Fitting (19) in each pin (5). Connect the lift arms to the bucket with a similar procedure.
Parts insulation Caterpillar catalog:
2032553
INSULATION
Caterpillar
Caterpillar
2027443
INSULATION KIT
Caterpillar
Caterpillar
2027441
INSULATION KIT
Caterpillar
Caterpillar
2027440
INSULATION KIT
Caterpillar
Caterpillar
2027439
INSULATION KIT
Caterpillar
Caterpillar
2027437
INSULATION KIT
Caterpillar
Caterpillar
2054636
INSULATION
Caterpillar
Caterpillar
2044277
INSULATION-
Caterpillar
Caterpillar
2043380
INSULATION
Caterpillar
Caterpillar
2038213
INSULATION
Caterpillar
Caterpillar
2038211
INSULATION
Caterpillar
Caterpillar
2038210
INSULATION
Caterpillar
Caterpillar