1427267 JET AS-PISTON COOLING Caterpillar parts
236, 248, 267, 287, 3034
Rating:
Alternative (cross code) number:
CA1427267
142-7267
1427267
CA1427267
142-7267
1427267
Weight: 0.06 pounds 0 kg.
MARINE ENGINE, SKID STEER LOADER,
Compatible equipment models: 1427267:
Number on catalog scheme:
14
For full view, you need register
Information:
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.
Illustration 1 g00101435
Park the machine on level ground. Lower the bucket to the ground so that the stick is vertical.
Move the hydraulic lockout control to the UNLOCKED position.
Turn the engine start switch to the ON position.
Move the joysticks and the travel levers/pedals to the full stroke positions in order to relieve the pressure in the pilot lines.
Turn the engine start switch to the OFF position and return the lever for the hydraulic lockout control to the LOCKED position.
Illustration 2 g01208340
Slowly loosen the fill/vent plug on top of the hydraulic tank in order to relieve the internal pressure of the hydraulic tank.
After the pressure is relieved, tighten the fill/vent plug.
Illustration 3 g00101497
Open the access door on the right side of the machine.
Illustration 4 g06312306
The case drain filter is located near the pilot oil filter.
Clean the area in order to keep dirt out of the filter base.Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information on containing fluid spillage.
Remove the used case drain filter from the filter base.Note: Used filters should always be disposed of according to local regulations.
Clean the filter base.
Illustration 5 g00101502
Coat the seal of a new case drain filter with clean hydraulic oil.
Install the new oil filter by hand.Instructions for the installation of the filter are printed on the side of each Caterpillar spin-on filter. For non-Caterpillar filters, refer to the installation instructions that are provided by the supplier of the filter.
Start the engine and operate the machine slowly for 10 to 15 minutes. Move each cylinder evenly through several cycles.
Illustration 6 g00101508
Return the machine to the position that is shown in Illustration 6. Check the machine for oil leaks.
Stop the engine.
Check the hydraulic oil level.Reference: For the correct procedure, refer to Operation and Maintenance Manual, "Hydraulic System Oil Level - Check".
Close the access door.
Caterpillar parts catalog:
Parts jet Caterpillar catalog:
3176C, 3196, 345B, 345B L, 365B, 365B II, 365B L, 75D, 972G II, C-10, C-12, C12, D7R II
3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 365B, 365B L, 480, 65E, 725, 730, 75D, 75E, 85D, 85E, 95E, 966G II, 972G II, C-10, C-12, R1600, TK1051, W345B II
3054, 3054B, 3056, 3056E, 307, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 424D, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438B, 438C, 438D, 442D, 550B, 554, 560B, 564, 574B, 908, 914...
3176, 3176B, 75, 75C, 85C, R1700 II
1259105
JET AS
416B, 428B, 438B
416B, 428B, 438B
212, 3054, 3056, 312, 315, 317, 416B, 426B, 428B, 438B, AP-800, AP-800C, BG-225B, CB-534B, CB-534C, CB-535B, CP-433C, CS-431B, CS-431C, PS-300B, RT50
16G, 16H NA, 245, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3412, 3412C, 578, 589, 621B, 621E, 621F, 623E, 627E, 627F, 631E, 637E, 651E, 657E, 769C, 771C, 773B, 775B, 826C, 834B, 836, 980C, 980F, 988B, ...
245, 3408, 3412, 637D, 651E, 657E, 834B, 988B, 992C, G3408
16G, 245, 3406, 3406B, 3408, 3412, 621, 637D, 639D, 651E, 657E, 773B, 980C, 988B, 992C, G3408
3176, 75
9R3468
JET AS
416, 426B, 428
416, 426B, 428
120M, 12M, 2470C, 3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 315C, 318D2 L, 320D GC, 320D L, 323D L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, ...