1515929 JET AS-PISTON COOLING Caterpillar parts
16G, 3406, 3406B, 3406C, 578, 980C, 980F
Rating:
Alternative (cross code) number:
CA1515929
151-5929
1515929
CA1515929
151-5929
1515929
Weight: 0.13 pounds 0 kg.
GEN SET ENGINE, WHEEL LOADER,
Compatible equipment models: 1515929:
Number on catalog scheme:
1
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Stud
1/2 - 13 NC by 7 inch 2 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01220951
Disconnect hose assemblies (1) from flywheel housing (2).
Disconnect fuel filter base (5) from flywheel housing (2). Reposition fuel filter base (5) and the hose assemblies.
Remove two bolts (4) and install Tooling (B).
Attach Tooling (A) and a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2) is approximately 110 kg (245 lb).
Remove remaining bolts (4), bolts (6), and bolts (3). Remove flywheel housing (2) and the gasket from the rear housing. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Stud
1/2 - 13 NC by 7 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01220951
Illustration 3 g01221009
Install Tooling (B) in the cylinder block.
Attach Tooling (A) and a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2) is approximately 110 kg (245 lb).
Position the gasket and flywheel housing (2) on the rear housing. Install bolts (3), bolts (6), and bolts (4).
Remove Tooling (B) and install remaining bolts (4).
Tighten the bolts, as follows:
In a numerical sequence, tighten Bolt 1 through Bolt 2 to a torque of 55 10 N m (41 7 lb ft).
In a numerical sequence, tighten Bolt 3 through Bolt 10 to a torque of 135 20 N m (100 15 lb ft).
In a numerical sequence, tighten Bolt 11 through Bolt 36 to a torque of 47 9 N m (35 7 lb ft).
Reposition fuel filter base (5) and the hose assemblies. Connect fuel filter base (5) to flywheel housing (2).
Connect hose assemblies (1) to flywheel housing (2). End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Stud
1/2 - 13 NC by 7 inch 2 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01220951
Disconnect hose assemblies (1) from flywheel housing (2).
Disconnect fuel filter base (5) from flywheel housing (2). Reposition fuel filter base (5) and the hose assemblies.
Remove two bolts (4) and install Tooling (B).
Attach Tooling (A) and a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2) is approximately 110 kg (245 lb).
Remove remaining bolts (4), bolts (6), and bolts (3). Remove flywheel housing (2) and the gasket from the rear housing. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Stud
1/2 - 13 NC by 7 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01220951
Illustration 3 g01221009
Install Tooling (B) in the cylinder block.
Attach Tooling (A) and a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2) is approximately 110 kg (245 lb).
Position the gasket and flywheel housing (2) on the rear housing. Install bolts (3), bolts (6), and bolts (4).
Remove Tooling (B) and install remaining bolts (4).
Tighten the bolts, as follows:
In a numerical sequence, tighten Bolt 1 through Bolt 2 to a torque of 55 10 N m (41 7 lb ft).
In a numerical sequence, tighten Bolt 3 through Bolt 10 to a torque of 135 20 N m (100 15 lb ft).
In a numerical sequence, tighten Bolt 11 through Bolt 36 to a torque of 47 9 N m (35 7 lb ft).
Reposition fuel filter base (5) and the hose assemblies. Connect fuel filter base (5) to flywheel housing (2).
Connect hose assemblies (1) to flywheel housing (2). End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Caterpillar parts catalog:
Parts jet Caterpillar catalog:
16G, 245, 3406, 3406B, 3408, 3412, 621, 637D, 639D, 651E, 657E, 773B, 980C, 988B, 992C, G3408
16G, 16H NA, 245, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3412, 3412C, 578, 589, 621B, 621E, 621F, 623E, 627E, 627F, 631E, 637E, 651E, 657E, 769C, 771C, 773B, 775B, 826C, 834B, 836, 980C, 980F, 988B, ...
16H NA, 3406B, 3406C, 583R, 587R, 621F, 623E, 623F, 627B, 627F, 814B, 980C, 980F, 980G, D350E, D400E, D8N, D8R, HT400, RM-250C, RR-250B
3406B, 3406C, 3406E, 375, 375 L, 5080, 980G, 980G II, C-15
3406E, 578, 824C, 980C, D8N
16H NA, 245B, 245D, 3406B, 3406C, 375, 375 L, 5080, 583R, 621F, 623E, 623F, 627B, 627F, 814B, 824G, 825G, 826G, 980G, D350E, D400E, D8R, RR-250B, SM-350
7E8456
JET AS-PISTON COOLING
3406B, 3412, 3412C, 3412E, PM3412, SCT673, SPS342, SPT342
3406B, 3412, 3412C, 3412E, PM3412, SCT673, SPS342, SPT342
3406B, 3406C, 3406E, 375, 375 L, 5080, R2900, RM-350B, SM-350
16H NA, 3406B, 3406C, 583R, 587R, 621F, 623E, 623F, 627B, 627F, 814B, 980C, 980F, 980G, D350E, D400E, D8N, D8R, HT400, RM-250C, RR-250B
3508, 3512, 3516, 5130, 5230, 776C, 777B, 784B, 785, 785B, 789, 789B, 793B, 994, D11N
24H, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 589, 631E, 633E II, 637E, 651E, 657E, 769C, 769D, 771D, 773D, 775D, 834B, 836, 844, 988F II, 990 II, AD40, AE40, D10R, D9R, PM-565, PM-565B
3408B, 3408C, 3412, 3412C, 836
9Y2606
JET AS-PISTON COOLING
3516, 789, G3516
3516, 789, G3516
24H, 3408E, 3412E, 5110B, 631D, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 69D, 769C, 769D, 771D, 773B, 773D, 773E, 775B, 775D, 775E, 834B, 836, 844, 988B, 988F II, 990, 990 II, 992C, AD45, AE40 II,...
3412, 3412C, 3412E, 5110B, PM3412, SCT673, SPS342, SPT342
16H NA, 245B, 245D, 3406B, 3406C, 375, 375 L, 5080, 583R, 621F, 623E, 623F, 627B, 627F, 814B, 824G, 825G, 826G, 980G, D350E, D400E, D8R, RR-250B, SM-350
3406E, 578, 824C, 980C, D8N
3406B, 3406C, 3406E, 375, 375 L, 5080, 980G, 980G II, C-15
3406C, 3406E