AVSPARE.COM
parts catalog

JOINT 0878516 - Caterpillar



0878516 JOINT Caterpillar parts E70B JOINT
Rating:
14
Alternative (cross code) number:
CA0878516
087-8516
0878516
Caterpillar 0878516 JOINT
Weight: 2 pounds 0 kg.

Buy JOINT 0878516 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 0878516:

EXCAVATOR  E70B   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 1 g02065914
Schematic for the Boom Up Pilot Pressure sensor This diagnostic code is associated with the Boom Up Pilot Pressure sensor. An FMI 04 diagnostic code means the machine ECM has determined the voltage in the sensor signal output circuit is below normal. Possible causes of this diagnostic code are:
The sensor may have failed.
The sensor output signal may be shorted to ground.
The Machine ECM may have failed. A failure of the Machine ECM is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes now, but clear those codes after the original diagnostic code has been corrected. Note: Poor connections are often the cause of a problem in electrical circuits. Before performing this procedure, inspect all of the harness connectors involved in the circuit. Verify that all of the connections in the circuit are clean, secure, and in good condition. If a problem is found with any of the connections: correct the problem and verify that diagnostic code CID 2429 FMI 04 is still active, before performing the following procedures. Test Step 1. CHECK THE SENSOR, THE ECM, AND THE CIRCUIT CONNECTIONS IN THE MACHINE HARNESS.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector from the Boom Up Pilot Pressure sensor.
Turn the key start switch and the disconnect switch to the ON position. Do NOT start the engine.
Observe the status of the diagnostic code.Expected Result:The CID 2429 FMI 04 diagnostic code does not change. Results:
YES - The diagnostic code does not change, and remains active. The sensor is NOT the cause of the problem. The machine harness may have failed, or the ECM may have failed. Go to Test Step 2.
NO - The CID 2429 FMI 04 diagnostic code is no longer active, and has changed into an active CID 2429 FMI 03 diagnostic code. The ECM has detected this valid diagnostic code. The ECM, and the harness, are correct. The sensor has failed. Replace the sensor. Go to Test Step 3. Test Step 2. CHECK THE SENSOR OUTPUT SIGNAL FOR A SHORT TO GROUND.
Turn the disconnect switch and the key start switch to the OFF position.
At the machine ECM, disconnect the J1 and J2 machine harness connectors from the ECM.
The harness connector remains disconnected from the Boom Up Pilot Pressure sensor.
At the ECM J1 harness connector, measure the resistance between the pin for contact J1-16 (M843-PU) and all of the other contacts used in the ECM harness connectors. Expected Result:Each measurement is more than 5000 ohms.Results:
YES - Each measurement is more than 5000 ohms. The sensor output signal circuit is NOT shorted to ground. Go to Test Step 3.
NO - One or more of the measurements are NOT more than 5000 ohms. There is a short in the harness. The short is between the sensor output signal wire and the wire with the low resistance. Repair, or replace, the harness. Go to Test Step 3. Test Step 3. CHECK IF THE DIAGNOSTIC CODE IS

Caterpillar parts catalog:

Caterpillar parts catalog
E70B TRACK-TYPE EXCAVATOR 5TG00001-UP (MACHINE) POWERED BY 4D32 ENGINE


Parts joint Caterpillar catalog:

0995905 JOINT
E110B, E120B, E140, E200B, E240C, E300B, E70B, EL240B
0996849 JOINT
E110B, E120B, E140, E200B, E240C, E300B, E70B, EL240B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.