AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

4W6013 GOVERNOR GP-PART 2 OF 2 TYPE 1. 4W7374-PAGE 98 PART OF 4W8929 & 4W6069 GOVERNOR, FUEL INJECTION & FUEL TRANSFER PUMP PR-750B


FUEL SYSTEM
GOVERNOR GP
PUMP GP-FUEL INJECTION
PUMP GP-FUEL TRANSFER
PUMP GP-FUEL INJECTION

COLD PLANER PR-750B COLD PLANER 8AC
 PR-750B PAVEMENT PROFILER 8AC00001-UP (MACHINE) POWERED BY 3412 ENGINE KEBP0051 PR-750B 8AC   (1985)

FUEL SYSTEM

GOVERNOR GP
PUMP GP-GOV, FUEL INJ & TFR
4W-6069 PUMP GP-GOV, FUEL INJ & TFR
GOVERNOR GP
4W-6013 GOVERNOR GP
4W-6013 GOVERNOR GP
GOVERNOR GP
4W-6013 GOVERNOR GP
4W-6013 GOVERNOR GP
PLATE GP-GOVERNOR ADAPTER
4W-7374 PLATE GP-GOVERNOR ADAPTER
 

#KEBP00510140
 

4W-6013: GOVERNOR GP

4W6013 GOVERNOR GP-PART 2 OF 2
TYPE 1.
4W7374-PAGE 98
PART OF 4W8929 & 4W6069 GOVERNOR, FUEL INJECTION & FUEL TRANSFER PUMP
c326777 KEBP0051
4W6013 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your PR-750B COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 5L-8992 [1] COVER-ADJUSTABLE  
2. 5P-6945 [1] BOLT  
  4B-9747 [1] WASHER  
3. 8L-4155 [1] SCREW-SET  
  1B-4201 [1] NUT-FULL  
4. 9M-4704 [1] BOLT  
5. 8L-4154 [1] COLLAR-LOAD STOP  
6. 2N-4386 [1] COVER  
7. 1B-2714 [2] BOLT  
  1B-4330 [2] NUT  
  5P-0537 [4] WASHER  
8. 6L-1597 [2] GASKET  
9. 2P-8669 [1] GASKET  
10. 2W-1491 [1] LEVER-CONTROL  
11. 9M-9788 [1] PLUNGER-STOP  
12. 7M-7316 [1] SPRING  
13. 5H-1351 [1] PIN-SPRING  
14. 2P-8679 [1] STRAINER AS  
15. 2P-8697 [1] GASKET  
16. 6N-3504 [1] SEAT-GOVERNOR SPRING  
17. 4N-1870 [1] GASKET-HOUSING  
18. 9S-8008 [1] PLUG-O-RING  
  3D-2824 [1] SEAL-O-RING  
19. 9S-4182 [1] PLUG  
  3J-7354 [1] SEAL-O-RING  
   
20. 4W-7374 Y [1] PLATE GP-GOVERNOR ADAPTER  
21. 6N-9040 [1] DRIVE AS-FLEXIBLE  
  6D-9953 [1] PIN-SPRING  
  9N-2428 [1] RIVET  
22. 2W-9780 [1] PIN AS  
23. 1B-9575 [1] BOLT  
24. 6N-8780 [1] STOP  
25. 8H-9181 [1] SPRING-BUMPER  
26. 5L-8991 [1] GASKET-COVER  
27. 4W-7654 [1] BOLT  
28. 6N-8793 [1] SPRING  
  Y   SEPARATE ILLUSTRATION
 

#KEBP00510141
 

4W-6013: GOVERNOR GP

4W6013 GOVERNOR GP-PART 1 OF 2
TYPE 2
PART OF 4W8929 GOVERNOR, FUEL INJECTION & FUEL TRANSFER PUMP
c503486 KEBP0051
4W6013 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your PR-750B COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-3363 [1] HOUSING AS-GOVERNOR  
2. 7E-8940 [1] BEARING-SLEEVE  
3. 8M-8403 [1] GUIDE-SPRING  
4. 9S-8001 [1] PLUG-O-RING  
  4J-7533 [1] SEAL-O-RING  
5. 7E-8941 [1] BEARING-SLEEVE  
6. 8T-2604 C [2] SEAL-LIP TYPE  
7. 8L-4308 [1] BOLT  
8. 3F-9556 [5] LOCKWASHER  
9. 2B-2695 [1] BOLT  
10. 2P-8707 [1] PLATE AS-GOVERNOR  
11. 8L-4175 [1] DOWEL  
12. 0S-1594 [1] BOLT  
13. 1D-4540 [3] BOLT  
14. 1N-4656 C [1] SHAFT-GOVERNOR CONTROL  
15. 9N-1917 [1] COVER AS-GOVERNOR  
16. 3P-0009 [1] INSULATOR-STUD  
17. 9N-1916 [1] LEVER-SHUT-OFF  
18. 5M-6228 [1] BEARING-NEEDLE  
19. 033-5359 C [4] SCREW-HEAD CAP  
20. 9N-2165 [1] LEVER-SOLENOID  
21. 1S-7984 [1] BEARING-SLEEVE  
22. 1K-4703 [1] WASHER  
23. 5P-0796 [2] SEAL-LIP TYPE  
24. 4N-0951 [1] SHAFT-SHUT-OFF  
25. 9N-3324 [1] SCREW-ADJUSTING (HI-IDLE)  
26. 8H-9204 [2] WASHER-FELT  
27. 7N-7325 [1] SCREW-ADJUSTING (LO-IDLE)  
28. 2J-0157 [2] SEAL-O-RING  
  C   CHANGE FROM PREVIOUS TYPE
 

#KEBP00510142
 

4W-6013: GOVERNOR GP

4W6013 GOVERNOR GP-PART 2 OF 2
TYPE 2
4W7374-PAGE 98
PART OF 4W8929 GOVERNOR, FUEL INJECTION & FUEL TRANSFER PUMP
c453751 KEBP0051
4W6013 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your PR-750B COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 5L-8992 [1] COVER-ADJUSTABLE  
2. 5P-6945 [1] BOLT  
  4B-9747 [1] WASHER  
3. 8L-4155 [1] SCREW-SET  
  1B-4201 [1] NUT-FULL  
4. 9M-4704 [1] BOLT  
5. 8L-4154 [1] COLLAR-LOAD STOP  
6. 7C-5279 C [1] COVER  
7. 4B-9365 C [2] BOLT  
  1B-4330 [2] NUT  
  5P-0537 [4] WASHER  
8. 8L-3873 C [2] GASKET  
9. 2P-8669 [1] GASKET  
10. 2W-1491 [1] LEVER-CONTROL  
11. 9M-9788 [1] PLUNGER-STOP  
12. 7M-7316 [1] SPRING  
13. 5H-1351 [1] PIN-SPRING  
14. 2P-8679 [1] STRAINER AS  
15. 2P-8697 [1] GASKET  
16. 6N-3504 [1] SEAT-GOVERNOR SPRING  
17. 4N-1870 [1] GASKET-HOUSING  
18. 9S-8008 [1] PLUG-O-RING  
  3D-2824 [1] SEAL-O-RING  
19. 9S-4182 [1] PLUG  
  3J-7354 [1] SEAL-O-RING  
20. 4W-7374 Y [1] PLATE GP-GOVERNOR ADAPTER  
21. 6N-9040 [1] DRIVE AS-FLEXIBLE  
  6D-9953 [1] PIN-SPRING  
  9N-2428 [1] RIVET  
22. 2W-9780 [1] PIN AS  
23. 1B-9575 [1] BOLT  
24. 6N-8780 [1] STOP  
25. 8H-9181 [1] SPRING-BUMPER  
26. 5L-8991 [1] GASKET-COVER  
27. 4W-7654 [1] BOLT  
28. 6N-8793 [1] SPRING  
29. 3L-5987 [1] COVER  
  C   CHANGE FROM PREVIOUS TYPE
  Y   SEPARATE ILLUSTRATION
 

#KEBP00510143
 

4W-6068: PUMP GP-FUEL INJECTION

4W6068 PUMP GP-FUEL INJECTION-PART 1 OF 2
TYPE 1
PART OF 4W8929 & 4W6069 GOVERNOR, FUEL INJECTION & FUEL TRANSFER PUMP
c326932 KEBP0051
4W6068 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your PR-750B COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-0824 [1] VALVE AS-BYPASS  
  7L-8696 [1] SPRING-BYPASS  
2. 3K-0360 [1] SEAL-O-RING  
3. 9S-4191 [2] PLUG-O-RING  
    14.28MM(.56IN)DIA THD EA
  3J-1907 [2] SEAL 15.85MM(.62 IN)OD  
4. 8N-0560 [1] GEAR (11 TEETH)  
5. 6N-7695 [1] COVER-OIL PUMP  
6. 5F-9144 [1] SEAL-O-RING  
7. 9S-8008 [2] PLUG-O-RING  
8. 3D-2824 [2] SEAL-O-RING  
9. 4N-0905 [1] GEAR-BEVEL (42 TEETH)  
10. 4N-0776 [1] RETAINER  
11. 0S-1618 [3] BOLT  
12. 5M-6214 [1] PLUG-PIPE  
13. 8N-0561 [1] GEAR IDLER-9 TEETH  
14. 6L-5897 [2] BOLT  
15. 6N-4165 [1] PINION AS-GOVERNOR DRIVE (12 TEETH)  
16. 6N-4090 [1] DOWEL  
 

#KEBP00510144
 

4W-6068: PUMP GP-FUEL INJECTION

4W6068 PUMP GP-FUEL INJECTION-PART 2 OF 2
TYPE 1
7N6124-PAGE 96 & 4W0101-PAGE 97
PART OF 4W8929 GOVERNOR, FUEL INJECTION & FUEL TRANSFER PUMP
c468091 KEBP0051
4W6068 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your PR-750B COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7N-6124 Y [1] HOUSING AS-PUMP  
2. 4N-2299 [1] RACK-REGULATING (L.H.)  
3. 1T-0284 [1] BOLT-SOCKET HEAD  
4. 2W-5128 [1] BRACKET AS-CONTROL  
5. 6N-6955 [1] PIN  
6. 6N-8447 [1] CAMSHAFT-FUEL PUMP  
7. 4N-1572 [1] LINK-RACK  
8. 4N-2298 [1] RACK-REGULATING (R.H.)  
9. 3D-2992 [12] SEAL  
10. 2M-4314 [12] BUSHING  
11. 8H-9204 [12] WASHER-FELT  
12. 4W-0101 Y [12] PUMP GP-FUEL INJECTION  
13. 8N-6981 [12] LIFTER AS  
   
   
   
   
   
   
   
   
   
   
   
   
   
14. 9N-6496 B [12] SPACER 4.11MM(.162IN)THK.  
  9N-6495 B [12] SPACER 4.21MM(.166IN)THK.  
  5M-2697 B [12] SPACER 4.32MM(.170IN)THK.  
  2M-4208 B [12] SPACER 4.42MM(.174IN)THK.  
  2M-4209 B [12] SPACER 4.52MM(.178IN)THK.  
  2M-4210 B [12] SPACER 4.62MM(.182IN)THK.  
  2M-4211 B [12] SPACER 4.72MM(.186IN)THK.  
  2M-4212 B [12] SPACER 4.83MM(.190IN)THK.  
  5M-2691 B [12] SPACER 4.93MM(.194IN)THK.  
  5S-7189 B [12] SPACER 5.03MM(.198IN)THK.  
  B   USE AS REQUIRED
  Y   SEPARATE ILLUSTRATION
 

#KEBP00510145
 

4W-6068: PUMP GP-FUEL INJECTION

4W6068 PUMP GP-FUEL INJECTION-PART 1 OF 2
TYPE 2
PART OF 4W8929 GOVERNOR, FUEL INJECTION & FUEL TRANSFER PUMP
c326932 KEBP0051
4W6068 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your PR-750B COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-0824 [1] VALVE AS-BYPASS  
  7L-8696 [1] SPRING-BYPASS  
2. 3K-0360 [1] SEAL-O-RING  
3. 9S-4191 [2] PLUG-O-RING  
    14.28MM(.56IN)DIA THD EA
  3J-1907 [2] SEAL 15.85MM(.62 IN)OD  
4. 8N-0560 [1] GEAR (11 TEETH)  
5. 6N-7695 [1] COVER-OIL PUMP  
6. 5F-9144 [1] SEAL-O-RING  
7. 9S-8008 [2] PLUG-O-RING  
8. 3D-2824 [2] SEAL-O-RING  
9. 4N-0905 [1] GEAR-BEVEL (42 TEETH)  
10. 4N-0776 [1] RETAINER  
11. 0S-1618 [3] BOLT  
12. 5M-6214 [1] PLUG-PIPE  
13. 8N-0561 [1] GEAR IDLER-9 TEETH  
14. 6L-5897 [2] BOLT  
15. 6N-4165 [1] PINION AS-GOVERNOR DRIVE (12 TEETH)  
16. 6N-4090 [1] DOWEL  
 

#KEBP00510146
 

4W-6068: PUMP GP-FUEL INJECTION

4W6068 PUMP GP-FUEL INJECTION-PART 2 OF 2
TYPE 2
7N6124-PAGE 96 & 7W0561-PAGE 97
PART OF 4W8929 GOVERNOR, FUEL INJECTION & FUEL TRANSFER PUMP
c583727 KEBP0051
4W6068 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your PR-750B COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7N-6124 Y [1] HOUSING AS-PUMP  
2. 4N-2299 [1] RACK-REGULATING (L.H.)  
3. 1T-0284 [1] BOLT-SOCKET HEAD  
4. 2W-5128 [1] BRACKET AS-CONTROL  
5. 6N-6955 [1] PIN  
6. 7W-0803 [1] CAMSHAFT-FUEL PUMP  
7. 4N-1572 [1] LINK-RACK  
8. 4N-2298 [1] RACK-REGULATING (R.H.)  
9. 114-8718 [12] SEAL-O-RING  
10. 7E-5085 [12] BUSHING  
11. 8H-9204 [12] WASHER-FELT  
12. 7W-0561 Y [12] PUMP GP-FUEL INJECTION  
13. 8N-6981 [12] LIFTER AS  
   
   
   
   
   
   
   
   
   
   
   
   
   
14. 9N-6496 B [12] SPACER 4.11MM(.162IN)THK.  
  9N-6495 B [12] SPACER 4.21MM(.166IN)THK.  
  5M-2697 B [12] SPACER 4.32MM(.170IN)THK.  
  2M-4208 B [12] SPACER 4.42MM(.174IN)THK.  
  2M-4209 B [12] SPACER 4.52MM(.178IN)THK.  
  2M-4210 B [12] SPACER 4.62MM(.182IN)THK.  
  2M-4211 B [12] SPACER 4.72MM(.186IN)THK.  
  2M-4212 B [12] SPACER 4.83MM(.190IN)THK.  
  5M-2691 B [12] SPACER 4.93MM(.194IN)THK.  
  5S-7189 B [12] SPACER 5.03MM(.198IN)THK.  
  B   USE AS REQUIRED
  Y   SEPARATE ILLUSTRATION
 

#KEBP00510147
 

7N-6124: HOUSING AS-FUEL PUMP

7N6124 HOUSING AS-PUMP
PART OF 4W6068 PUMP-FUEL INJECTION
c334439 KEBP0051
7N6124 HOUSING AS-FUEL PUMP Parts scheme
  For full view, you need register

Parts for your PR-750B COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6N-7266 [1] SHAFT-PUMP IDLER  
2. 7N-0242 C [2] BEARING-SLEEVE  
3. 8L-6565 [1] PIN-SPRING  
4. 4N-0952 C [1] PLUG-CUP  
5. 5B-9318 C [1] BALL  
6. 4M-1474 [1] PIN-LIFTER GUIDE  
7. 9L-9766 [2] PIN-PLUNGER LIFT  
8. 1P-0232 [12] BALL  
  1P-0234 [12] DOWEL  
9. 1S-2199 [1] DOWEL  
10. 9S-4160 [2] BEARING-SLEEVE  
11. 6N-8442 [1] BEARING-SLEEVE  
12. 7M-5839 [1] PLUG-CUP  
13. 6N-8441 [2] BEARING-SLEEVE  
14. 4N-0775 [2] DOWEL-HOLLOW  
  C   CHANGE FROM PREVIOUS TYPE
 

#KEBP00510148
 

7W-0561: PUMP GP-FUEL INJECTION

7W0561 PUMP GP-FUEL INJECTION
PART OF 4W6068 PUMP-FUEL INJECTION
c353004 KEBP0051
7W0561 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your PR-750B COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1W-9171 [1] BONNET-VALVE  
2. 8N-1415 [1] SPRING-CHECK  
3. 1W-6987 [1] VALVE AS-CHECK  
4. 7W-1927 [1] RING-RETAINER  
5. 7W-0182 [1] PLUNGER & BARREL AS  
6. 7C-5278 C [1] BOLT-GEAR  
7. 7N-1066 C [1] WASHER-RETAINER  
  C   CHANGE FROM PREVIOUS TYPE
 

#KEBP00510149
 

4W-0101: PUMP GP-FUEL INJECTION

4W0101 PUMP GP-FUEL INJECTION
REPLACED BY 7W0561-PAGE 97
PART OF 4W6068 PUMP-FUEL INJECTION
c316909 KEBP0051
4W0101 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your PR-750B COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1W-9171 [1] BONNET-VALVE  
2. 8N-1415 [1] SPRING-CHECK  
3. 1W-6987 [1] VALVE AS-CHECK  
4. 1M-3506 [1] RING-RETAINER  
5. 7N-1208 [1] SPRING-LIFTER  
6. 7N-1066 [1] WASHER-RETAINER  
7. 6N-7828 [1] PLUNGER AS-FUEL PUMP  
8. 8H-9299 [1] SCREW-PLUNGER GEAR  
 

Information:

Engine News
New Woodward Governor Control Used On Diesel Engines; Former Control Now Used On Gas Engines Only
1979/04/04
Conversion Group Available To Install Woodward Governor On Engines Equipped With Mechanical Governor
1979/04/25
To Prevent A Possible Change In The Fuel Rack Setting, A Specific Assembly Procedure Must Be Used To Tighten The Bolt On The Governor Stop Collar
1979/08/08
Explanation Of Differences In Timing Advance Information
1981/08/26
Part Number For Fuel Injection Pump Group In New Location
1981/11/25
New Idler Shaft Used In Fuel Transfer Pumps
1982/02/24
Fuel Rack Slots Have Improved Wear Resistance
1982/05/12
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25
Changes In Engine RPM; Governor Does Not Operate Correctly
1982/10/20
Changes In Engine RPM; Governor Does Not Operate Correctly
1983/01/19
New Specification For Clearance Between Fuel Rack Slot And Cross Link
1983/05/25
Improved Governor Control Shaft And Seal Will Help Prevent Oil Leakage
1983/07/06
Service Information For Woodward Governors
1983/10/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint
1983/11/30
Procedure To Remove Sharp Edges From Fuel Racks
1984/02/22
New EG3P Actuator Assemblies Available
1984/03/07
Overvoltage Protection For Woodward 2301 Governor
1984/04/11
Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators
1984/05/16
New Seal For Fuel Injection Pump Housing Is More Resistant To Heat Damage
1984/05/16
New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage
1984/06/20
Fill Oil Sump Before Installing Woodward Governor
1985/01/16
Cross Link Between Fuel Racks Has Smoother Surface
1985/03/01
Changes To Fuel Systems
1985/09/01
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings
1985/12/01
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct
1986/05/01
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01
More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups
1986/06/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
New Steel Fuel Injection Pump Lifters Should Not Be Mixed With Aluminum Lifters
1987/10/01
New Fuel Shutoff Solenoid Assembly Used
1988/11/01
New Throttle Shaft Bearing Sleeves Used In Governor Housing Assembly
1990/08/01
Governor Control Motor Polarity May Require A Change
1990/11/01
Replace Camshaft And Install New Lifters If Pitting, Spalling, Or Wear Occurs On Lobes Of 4N0599 And 4N0602 Camshafts In Fuel Injection Pump Groups
1991/05/01
Corrections For Systems Operation, Troubleshooting, And Specifications For 2301 Electric Governors For Generator Set And Industrial Engines, SENR2928-01
1991/05/01
Procedure To Increase Fuel Transfer Pump Pressure {1256}
1995/04/01
Pressure Compensated Simple Governor (PSG Governor) Changes From Aluminum To Cast Iron Housing {1264}
1995/04/01
Woodward Control Assemblies Have Changed Part Numbers To Provide The CE Marking For Electromagnetic Compatibility (EMC) Directives{1264}
1996/05/09
Improved Governor Servo Components Available For Use With Energize To Run Solenoids; Energize To Run Solenoid Stop Bolt Adjustment Procedure{1264,1259}
1996/06/12
New Spring Used In Fuel Ratio Control
1977/03/15
New 5P4185 Fuel Pump Timing Pin To Be Used Only On 3408 And 3412 Engines
1977/05/13
Improvements To Fuel Injection Pump And Governor
1977/06/08
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Fuel Transfer Pump Shaft With Chromium Plate
1977/10/12
New Governor Spring Changes Speed Regulation
1977/11/09
Change In Design Of Engine Governor, Fuel Injection And Transfer Pump Groups, And Fuel Ratio Control Groups
1978/02/08
New Tachometer Drive Adapter Assembly Prevents Failure Of The Seals For The Tachometer Drive Group And Transfer Pump
1978/03/01
O-Ring Seals Of A Different Material Are Now Used On The Outside Diameter Of The Servo Cylinder In Governors
1978/05/03
A One-Piece Spring Seat Is Now Used In The Governor
1978/07/05
New Dashpot Spring Gives A Reduction In "Overshoot"
1978/07/05
Different O-Ring Seals Now Used In Fuel Injection Pump Group
1978/08/30
Special Instruction
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Fuel System and Fuel Ratio Control Test Procedure{1264, 1278}
Fuel System and Fuel Ratio Control Test Procedure{1264, 1278}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Wiring Polarity on Woodward 2301 Governors{1289}
Wiring Polarity on Woodward 2301 Governors{1289}
Installation Of 6N6193 Governor Adapter Plate Service Group{1264}
Installation Of 6N6193 Governor Adapter Plate Service Group{1264}
Installation Of 4N779 And 7N6124 Fuel Injection Pump Housing Assemblies Or Fuel Injection Pump Groups{1251, 1253}
Installation Of 4N779 And 7N6124 Fuel Injection Pump Housing Assemblies Or Fuel Injection Pump Groups{1251, 1253}
Governor Linkage Adjustments{1264, 1289}
Governor Linkage Adjustments{1264, 1289}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N3104 Governor Conversion Group (Woodward PSG){1250}
Installation Of 8N3104 Governor Conversion Group (Woodward PSG){1250}
Installation Of 4W5391 Preregulator Box Assembly{1289}
Installation Of 4W5391 Preregulator Box Assembly{1289}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Service Letter-NACD
The Governors Need To Be Reworked On Certain 3412 Engines Equipped With A 9Z5359 Modification (High Output 3412 Custom Marine Engine)
The Governors Need To Be Reworked On Certain 3412 Engines Equipped With A 9Z5359 Modification (High Output 3412 Custom Marine Engine)
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Truck/Ag/Marine
Technical Information Bulletin
Remanufactured Fuel Injection Nozzles
Remanufactured Fuel Injection Nozzles
3400 V - Block Cleaniness at Gov'n Oil Supply Line
3400 V - Block Cleaniness at Gov'n Oil Supply Line
Specifications
Fuel Injection Pump
3408C & 3412C INDUSTRIAL ENGINES
Fuel Injection Pump Housing
3408C & 3412C INDUSTRIAL ENGINES
Governor
3408C & 3412C INDUSTRIAL ENGINES
Governor And Fuel Pump Drive<BR> (Automatic Timing Advance Unit)
3408C & 3412C INDUSTRIAL ENGINES
Fuel Transfer Pump Drive
3408C & 3412C INDUSTRIAL ENGINES
Fuel Transfer Pump
3408C & 3412C INDUSTRIAL ENGINES
Governor Control
3408C & 3412C INDUSTRIAL ENGINES
Fuel System Identification
3412 INDUSTRIAL AND MARINE ENGINES
Fuel Injection
3412 INDUSTRIAL AND MARINE ENGINES
Governor
3412 INDUSTRIAL AND MARINE ENGINES
Fuel Injection Pump Housing (Earlier)
3412 INDUSTRIAL AND MARINE ENGINES
Fuel Injection Pump Housing (Later)
3412 INDUSTRIAL AND MARINE ENGINES
Governor Drive And Oil Pump
3412 INDUSTRIAL AND MARINE ENGINES
Governor And Fuel Pump Drive (Automatic Timing Advance Unit) (Standard Engine)
3412 INDUSTRIAL AND MARINE ENGINES
Governor And Fuel Pump Drive (Automatic Timing Advance Unit) (Low Speed Engine)
3412 INDUSTRIAL AND MARINE ENGINES
Fuel Ratio Control
3412 INDUSTRIAL AND MARINE ENGINES
Fuel Transfer Pump
3412 INDUSTRIAL AND MARINE ENGINES
Fuel Transfer Pump Drive
3412 INDUSTRIAL AND MARINE ENGINES
Woodward PSG Governor
3412 INDUSTRIAL & MARINE ENGINE ATTACHMENTS
Governor Linkage
3412 INDUSTRIAL & MARINE ENGINE ATTACHMENTS
Governor Controls
3412 INDUSTRIAL & MARINE ENGINE ATTACHMENTS
Governor Air Actuator
3412 INDUSTRIAL & MARINE ENGINE ATTACHMENTS
Service Letter-China
The Governors Need To Be Reworked On Certain 3412 Engines Equipped With A 9Z5359 Modification (High Output 3412 Custom Marine Engine)
The Governors Need To Be Reworked On Certain 3412 Engines Equipped With A 9Z5359 Modification (High Output 3412 Custom Marine Engine)
Service Letter-Asia
Systems Operation
Systems Operation
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Installation And Operation
2301A SPEED CONTROL
Service Letter-APD
The Governors Need To Be Reworked On Certain 3412 Engines Equipped With A 9Z5359 Modification (High Output 3412 Custom Marine Engine)
The Governors Need To Be Reworked On Certain 3412 Engines Equipped With A 9Z5359 Modification (High Output 3412 Custom Marine Engine)
Testing and Adjusting
Testing and Adjusting
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Installation And Operation
2301A SPEED CONTROL
Troubleshooting
Introduction
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem Index
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 1: Fuel Linkage Has Limited Travel, Binds, Or Takes Excessive Force
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 2: Engine Will Not Start
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 3: Engine Will Not Carry Load (Low Power)
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 4: Engine Will Not Decelerate. Engine Will Not Idle.
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 5: Engine Speed Not Constant
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 6: Engine Overspeeds
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 7: Engine Does Not Share Load (For Load Share Units Only)
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 8: Engine Does Not Parallel
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Service Procedures
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Chapter 5. Troubleshooting
2301A SPEED CONTROL
Appendix A. Guide for Handling and Protection of Electronic Controls, Printed Circuit Boards, &amp; Modules
2301A SPEED CONTROL
Appendix B. EMI Controls in Electronic Governing Systems
2301A SPEED CONTROL
Disassembly and Assembly
Governor &amp; Fuel Pump Drive
3408C & 3412C INDUSTRIAL ENGINES
Fuel Injection Pumps
3408C & 3412C INDUSTRIAL ENGINES
Fuel Transfer Pump
3408C & 3412C INDUSTRIAL ENGINES
Governor &amp; Fuel Injection Pump Housing
3408C & 3412C INDUSTRIAL ENGINES
Fuel Shutoff Solenoid
3408C & 3412C INDUSTRIAL ENGINES
Fuel Ratio Control
3412 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
3412 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pumps
3412 INDUSTRIAL & MARINE ENGINES
Automatic Timing Advance
3412 INDUSTRIAL & MARINE ENGINES
Governor (Low Speed Engine)
3412 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing &amp; Governor
3412 INDUSTRIAL & MARINE ENGINES
Service Magazine
Modification Of 5P1768 Pointer Assembly Necessary For Use On Some Fuel Injection Pump Housings{1253,0653}
1980/03/31
6V2029 Fixture Group Available For Adjustment Of Air/Fuel Ratio Control {0626,1278,0652}
1981/03/23
Troubleshooting The Fuel Ratio Control Group For Low Power Complaints{1278}
1981/08/24
Part Number For Fuel Injection Pump Group In New Location{1253,1286}
1981/11/09
New Idler Shaft Used In Fuel Transfer Pumps{1256}
1982/02/22
Fuel Rack Slots Have Improved Wear Resistance{1257}
1982/05/10
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Changes In Engine RPM; Governor Does Not Operate Correctly{1264}
1982/10/18
Changes In Engine RPM; Governor Does Not Operate Correctly{1264}
1983/01/10
New Rack Shutoff Solenoid Available{1257,1259}
1983/02/28
New Specification For Clearance Between Fuel Rack Slot And Cross Link{1257}
1983/05/16
Improved Governor Control Shaft And Seal Will Help Prevent Oil Leakage{1265}
1983/07/04
Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15
Service Information For Woodward Governors{0374,1264}
1983/09/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Procedure To Remove Sharp Edges From Fuel Racks {1257,1253}
1984/02/06
New EG3P Actuator Assemblies Available{1289}
1984/02/27
Overvoltage Protection For Woodward 2301 Governor{1289}
1984/04/09
Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators{1265,1289}
1984/04/23
New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage{1264}
1984/05/14
Fill Oil Sump Before Installing Woodward Governor{1264,1288,1289}
1984/12/10
Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14
Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04
Cross Link Between Fuel Racks Has Smoother Surface{1250,1257}
1985/03/11
Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02
Steel Fuel Pump Lifter Used{1250,1251}
1985/09/02
Changes To Fuel Systems {1250,1251,1252,1253,1254,1100}
1985/09/16
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control{1400,1401,4450}
1986/03/24
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05
More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups{1265,1264,1250}
1986/06/02
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
Improvements To Fuel Injection Pump And Governor{1286}
1977/06/06
Fuel Transfer Pump Shaft With Chromium Plate{1256}
1977/10/10
New Governor Spring Changes Speed Regulation{1264,1286}
1977/10/31
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Change In Design Of Engine Governor, Fuel Injection And Transfer Pump Groups, And Fuel Ratio Control Groups{1264,1278,1286}
1978/01/23
Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/01/30
New Tachometer Drive Adapter Assembly Prevents Failure Of The Seals For the Tachometer Drive Group And Transfer Pump{7462,1256}
1978/02/27
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
O-Ring Seals Of A Different Material Are Now Used On The Outside Diameter Of The Servo Cylinder In Governors{1264}
1978/05/01
New Dashpot Spring Gives A Reduction In &quot;Overshoot&quot;{1264}
1978/06/26
A One-Piece Spring Seat Is Now Used In The Governor{1264}
1978/06/26
Different O-Ring Seals Now Used In Fuel Injection Pump Group{1251}
1978/08/28
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
New Woodward Governor Control Used On Diesel Engines; Former Control Now Used On Gas Engines Only{1265}
1979/03/19
Conversion Group Available To Install Woodward Governor On Engines Equipped With Mechanical Governor{1264}
1979/04/09
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
To Prevent A Possible Change In The Fuel Rack Setting, A Specific Assembly Procedure Must Be Used To Tighten The Bolt On The Governor Stop Collar{1259,1257,1250}
1979/07/02
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10
New Throttle Shaft Bearing Sleeves Used In Governor Housing Assembly{1365}
1990/07/30
Governor Control Motor Polarity May Require A Change{1265,1408,7556}
1990/10/29
Replace Camshaft And Install New Lifters If Pitting, Spalling, Or Wear Occurs On Lobes Of 4N0599 And 4N0602 Camshafts In Fuel Injection Pump Groups{1251,1253}
1991/05/20
New Components Help Prevent Air Leaks In Improved Fuel Ratio Control Groups{1278}
1992/05/25
New Diaphragm Used In Fuel Ratio Control Groups{1278}
1992/06/15
Improved Fuel Pump Bonnet Seal Has Better Heat Resistance {1251}
1994/09/12
Tamper Resistant Plugs And Tamper Resistant Bolts Used To Prevent Changes To Fuel Ratio Control (FRC) Setting{1278,1287}
1996/01/22
Improved Governor Servo Components Available For Use With Energize To Run Solenoids; Energize To Run Solenoid Stop Bolt Adjustment Procedure{1264,1259}
1996/06/03

Caterpillar Parts SIS Catalog PR-750B :

GOVERNOR GP
4W-6013 GOVERNOR GP
PUMP GP-GOV, FUEL INJ & TFR
4W-6069 PUMP GP-GOV, FUEL INJ & TFR
PUMP GP-FUEL TRANSFER
4W-5477 PUMP GP-FUEL TRANSFER
PUMP GP-FUEL TRANSFER
4N-1101 PUMP GP-FUEL TRANSFER
PUMP GP-GOV, FUEL INJ & TFR
4W-8929 PUMP GP-GOV, FUEL INJ & TFR
CONTROL GP-GOVERNOR
3N-7741 CONTROL GP-GOVERNOR
PUMP GP-FUEL PRIMING
4N-3287 PUMP GP-FUEL PRIMING
DRIVE GP-GOVERNOR & FUEL PUMP
6N-3195 DRIVE GP-GOVERNOR & FUEL PUMP
GOVERNOR GP
4W-6013 GOVERNOR GP
4W-6013 GOVERNOR GP
PUMP GP-FUEL INJECTION
4W-6068 PUMP GP-FUEL INJECTION
4W-6068 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
4W-6068 PUMP GP-FUEL INJECTION
4W-6068 PUMP GP-FUEL INJECTION
HOUSING AS-FUEL PUMP
7N-6124 HOUSING AS-FUEL PUMP
PUMP GP-FUEL INJECTION
7W-0561 PUMP GP-FUEL INJECTION

Truck sale:

CAT PR-750B
USD $49,900 
CAT PR-750B

AUG MAQUINARIA
Monterrey, Nuevo Leon, Mexico
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.