AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

1W-3897 TURBOCHARGER GP S/N 48W34817-99999 PART OF 1W-0412 TURBOCHARGER GP PM-565 COLD PLANER


AIR INLET AND EXHAUST SYSTEM
TURBOCHARGER GP
FUEL SYSTEM
CONTROL GP-GOVERNOR
GOVERNOR GP
DRIVE GP-TACHOMETER
PUMP GP-FUEL TRANSFER
FILTER GP-FUEL
GOVERNOR GP

COLD PLANER PM-565 COLD PLANER 3TK
 PM-565 Cold Planer 3TK00001-00112 (MACHINE) POWERED BY 3408 Engine KEBP0105 PM-565 3TK   (1992)

AIR INLET AND EXHAUST SYSTEM

TURBOCHARGER GP
CARTRIDGE GP-TURBOCHARGER
4N-7601 CARTRIDGE GP-TURBOCHARGER
TURBOCHARGER GP
1W-0412 TURBOCHARGER GP
TURBOCHARGER GP
1W-3897 TURBOCHARGER GP
 

#KEBP01050090
 

1W-3897: TURBOCHARGER GP

1W-3897 TURBOCHARGER GP
S/N 48W34817-99999
PART OF 1W-0412 TURBOCHARGER GP
i00107798 KEBP0105
1W3897 TURBOCHARGER GP Parts scheme
  For full view, you need register

Parts for your PM-565 COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-8123 [1] COVER-COMPRESSOR  
2. 4N-7601 Y [1] CARTRIDGE GP-TURBOCHARGER  
3. 1W-4795 B [1] PLATE-IDENTIFICATION (TURBOCHARGER CARTRIDGE)  
  2Y-4541 B [1] PLATE-IDENTIFICATION (BRAZIL USAGE)  
  8H-3710 [2] SCREW-TAPPING (6-32X0.375-IN)  
4. 1W-3898 [1] HOUSING  
5. 5S-4517 [1] CLAMP AS (TURBINE)  
  7M-9918 [1] LOCKNUT (1/4-28-THD)  
6. 2S-1304 [1] CLAMP AS (COMPRESSOR)  
  7M-9918 LOCKNUT (1/4-28-THD)  
  B   USE AS REQUIRED
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#KEBP01050091
 

1G-8626: CONTROL GP-GOVERNOR

1G-8626 CONTROL GP-GOVERNOR
S/N 3TK1-112
PART OF 086-9598 INSTALLATION AR-ENGINE
i00351677 KEBP0105
1G8626 CONTROL GP-GOVERNOR Parts scheme
  For full view, you need register

Parts for your PM-565 COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4W-7773 [1] MOTOR AS  
  7N-9738 [1] HOUSING-RECEPTACLE (14-GA TO 18-GA)  
  7N-7780 [1] PIN-CONNECTOR (14-GA TO 18-GA)  
  7N-7779 [1] SOCKET-CONNECTOR (14-GA TO 18-GA)  
2. 1A-2029 [1] BOLT (3/8-16X1.125-IN)  
  5P-1075 [2] WASHER-HARD (10.2X22.5X3-MM THK)  
  9S-8752 [1] NUT-FULL (3/8-16-THD)  
3. 9S-8751 [2] NUT-FULL (5/16-24-THD)  
4. 3N-7741 Y [1] CONTROL GP-GOVERNOR  
5. 1G-9048 [1] BRACKET  
6. 0S-1615 [2] BOLT (1/4-20X0.75-IN)  
7. 5P-0537 [7] WASHER-HARD (7.2X14.5X2-MM THK)  
8. 9F-6580 [2] BOLT (1/4-20X1.125-IN)  
9. 8G-0759 [1] ROD  
10. 2D-6235 [2] LOCKNUT (1/4-20-THD)  
11. 1H-8289 [4] SCREW-MACHINE  
  3K-9089 [4] NUT-SELF LOCKING (5-40-THD)  
12. 7B-2742 [1] BOLT (1/4-20X1.25-IN)  
13. 8N-0076 [1] LEVER-GOVERNOR  
14. 7F-1906 [1] CLIP  
  8N-0075 [1] DAMPER  
15. 7L-4186 [2] ROD END  
  Y   SEPARATE ILLUSTRATION
 

#KEBP01050092
 

3N-7741: CONTROL GP-GOVERNOR

3N-7741 CONTROL GP-GOVERNOR
S/N 3TK1-112
PROVIDES MULTI-HOLE GOVERNOR CONTROL
PART OF 1G-8626 CONTROL GP-GOVERNOR
i00366743 KEBP0105
3N7741 CONTROL GP-GOVERNOR Parts scheme
  For full view, you need register

Parts for your PM-565 COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 5L-1171 [1] LEVER-GOVERNOR CONTROL  
2. 0S-1618 [1] BOLT (5/16-18X1-IN)  
 

#KEBP01050093
 

9N-3959: DRIVE GP-GOVERNOR & FUEL PUMP

9N-3959 DRIVE GP-GOVERNOR & FUEL PUMP
S/N 48W34817-99999
PART OF 6I-2565 ENGINE AR
i00148058 KEBP0105
9N3959 DRIVE GP-GOVERNOR & FUEL PUMP Parts scheme
  For full view, you need register

Parts for your PM-565 COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 5J-5793 [4] BOLT-12 POINT HEAD (1/2-13X2-IN)  
2. 6N-3927 [1] RETAINER  
3. 9N-5075 [1] FLANGE AS  
4. 6N-2533 [1] GEAR AS-ADVANCE (86-TEETH)  
5. 8H-0333 [2] PISTON  
6. 6N-2523 [2] SLIDE  
7. 6N-5156 [2] WEIGHT-ADVANCE  
8. 6N-0493 [1] RING  
9. 9N-5077 [2] SPRING (OUTER)  
10. 9N-5078 [2] SPRING (INNER)  
 

#KEBP01050094
 

2W-2094: DRIVE GP-TACHOMETER

2W-2094 DRIVE GP-TACHOMETER
S/N 48W34817-36022
PART OF 6I-2565 ENGINE AR
i00147577 KEBP0105
2W2094 DRIVE GP-TACHOMETER Parts scheme
  For full view, you need register

Parts for your PM-565 COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4M-8303 [1] SEAL-O-RING  
2. 9S-3032 [2] CLAMP  
3. 4W-6538 C [1] ADAPTER AS-DRIVE  
4. 0S-1617 [2] BOLT (5/16-18X0.75-IN)  
5. 9B-2232 C [1] CAP-TACHOMETER DRIVE  
6. 7H-9899 C [1] SEAL  
  C   CHANGE FROM PREVIOUS TYPE
 

#KEBP01050095
 

9Y-3764: FASTENER GP-FUEL INJ PUMP

9Y-3764 FASTENER GP-FUEL INJ PUMP
S/N 48W34817-99999
PART OF 4W-7199 PUMP GP-GOV, FUEL INJ & TFR
i00108459 KEBP0105
9Y3764 FASTENER GP-FUEL INJ PUMP Parts scheme
  For full view, you need register

Parts for your PM-565 COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 0S-1594 [4] BOLT (3/8-16X1-IN)  
2. 3B-1915 [4] BOLT (3/8-16X1.375-IN)  
3. 0S-1571 [6] BOLT (3/8-16X1.75-IN)  
4. 0L-1143 [1] BOLT (3/8-16X2.5-IN)  
5. 053-2294 [1] BOLT-12 POINT HEAD (3/8-16X1.75-IN)  
 

#KEBP01050096
 

7R-9855: FILTER & LINES GP-FUEL

7R-9855 FILTER & LINES GP-FUEL
S/N 3TK1-112
PART OF 086-9598 INSTALLATION AR-ENGINE
i00419916 KEBP0105
7R9855 FILTER & LINES GP-FUEL Parts scheme 7R9855 FILTER & LINES GP-FUEL Parts scheme
  For full view, you need register

Parts for your PM-565 COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 101-9212 I [1] HOSE AS (MARKED A)  
2. 101-9211 I [1] HOSE AS (MARKED B)  
3. 7W-9546 [1] TUBE AS-SUPPLY  
    (MARKED C)
4. 1G-9780 [1] TUBE AS (MARKED D)  
5. 102-1758 I [1] HOSE AS (MARKED E)  
6. 101-9209 I [1] HOSE AS (MARKED F)  
7. 101-9208 I [1] HOSE AS (MARKED G)  
8. 101-9210 I [1] HOSE AS (MARKED H)  
9. 101-9207 I [1] HOSE AS (MARKED J)  
10. 9S-4182 [1] PLUG (7/16-20-THD)  
11. 4N-1981 Y [1] FILTER GP-FUEL  
12. 3J-7354 [3] SEAL-O-RING  
13. 030-7947 [1] ELBOW  
14. 030-8156 [1] ELBOW  
15. 3J-1907 [2] SEAL-O-RING  
16. 107-8231 [1] BRACKET AS  
17. 6V-8801 [2] NUT (3/8-16-THD)  
18. 9N-3666 [1] VALVE-MANUAL  
19. 9B-7237 [1] BOLT (3/8-16X1.25-IN)  
20. 8T-4896 [10] WASHER-HARD (10.2X18.5X2.5-MM THK)  
21. 6N-4414 [1] COVER-FILTER BASE  
22. 1P-0436 [2] GASKET (FUEL PRIMING PUMP)  
23. 7X-2501 [2] BOLT (1/4-20X1.25-IN)  
  8T-4205 [2] WASHER-HARD (7.2X14.5X2-MM THK)  
  6V-8918 [2] BOLT (5/16-18X1.25-IN)  
  8T-4224 [2] WASHER-HARD (8.8X16X2-MM THK)  
24. 6V-9002 [1] ELBOW  
25. 3K-0360 [2] SEAL-O-RING  
26. 6K-8178 [1] CLIP  
27. 4V-0611 [4] CLAMP  
28. 4V-0612 [2] PLATE  
29. 7X-0440 [1] BOLT (5/16-18X1.75-IN)  
30. 7J-9108 [1] SEAL-O-RING  
31. 5P-9298 [3] CLIP  
32. 1B-2790 [2] BOLT (5/16-18X1.375-IN)  
33. 5P-4116 [2] WASHER-HARD (8.8X20.5X2-MM THK)  
34. 5S-7383 [2] BOLT (3/8-16X1.75-IN)  
35. 8C-3115 [1] TEE  
36. 6V-8397 [3] SEAL-O-RING  
37. 1G-9904 [1] BRACKET AS  
38. 5M-3062 [3] BOLT (3/8-16X0.75-IN)  
39. 5P-9297 [3] CLIP  
40. 4L-6459 [1] BOLT (3/8-16X2.5-IN)  
41. 4W-4592 [1] BRACKET AS  
42. 1G-9926 [1] BRACKET AS  
43. 4L-6454 [2] BOLT (3/8-16X1-IN)  
44. 6V-8939 [1] REDUCER-O-RING  
45. 6V-8555 [1] NUT-FACE SEAL (1-14-THD)  
46. 6V-8398 [9] SEAL-O-RING  
47. 6N-1044 Y [1] FILTER GP-PRIMARY FUEL  
48. 5P-1075 [2] WASHER-HARD (10.2X22.5X3-MM THK)  
49. 4L-9337 [1] BOLT (3/8-16X1.5-IN)  
50. 105-2508 [1] PUMP AS-FUEL PRIMING  
51. 8C-6871 [1] CONNECTOR  
52. 6V-8721 [1] ELBOW  
53. 2M-9780 [1] SEAL-O-RING  
54. 6V-8981 [1] ELBOW  
55. 8T-0130 [1] ELBOW  
56. 6V-9169 [1] NUT (13/16-16-THD)  
57. 6V-9168 [1] NUT (11/16-16-THD)  
58. 6V-8639 [1] CONNECTOR  
59. 8T-8911 [1] BOLT (5/16-18X2-IN)  
  I   REFER TO HYDRAULIC INFORMATION SYSTEM
  Y   SEPARATE ILLUSTRATION
 

#KEBP01050097
 

4N-1981: FILTER GP-FUEL

4N-1981 FILTER GP-FUEL -ENGINE
S/N 3TK1-112
PART OF 7R-9855 FILTER & LINES GP-FUEL
i00107917 KEBP0105
4N1981 FILTER GP-FUEL Parts scheme
  For full view, you need register

Parts for your PM-565 COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1N-3789 C [1] BASE AS-FILTER (FUEL)  
2. 9S-4167 [1] STUD-HOLLOW (1-14X1.47-IN)  
3. 1R-0749 [1] FILTER-FUEL (ADVANCED EFFICIENCY)  
  C   CHANGE FROM PREVIOUS TYPE
 

#KEBP01050098
 

6N-1044: FILTER GP-PRIMARY FUEL

6N-1044 FILTER GP-PRIMARY FUEL
S/N 3TK1-112
PART OF 7R-9855 FILTER & LINES GP-FUEL
i00147262 KEBP0105
6N1044 FILTER GP-PRIMARY FUEL Parts scheme
  For full view, you need register

Parts for your PM-565 COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8H-2807 [1] NUT (3/8-24-THD)  
  8N-4410 [1] WASHER  
2. 6N-1045 [1] BASE AS-FUEL FILTER  
3. 7E-5346 [1] VALVE AS  
4. 1L-3769 [1] RING-RETAINING  
5. 8H-2778 [1] SEAL-RING  
6. 9M-2341 [1] FILTER ELEMENT-WTR SEP & FUEL (STANDARD EFFICIENCY)  
7. 8H-2810 [1] CASE AS-FILTER  
8. 7H-9678 [1] RETAINER-ELEMENT  
9. 2H-3429 [1] RING-RETAINING  
10. 7S-9323 [1] SPRING  
 

#KEBP01050099
 

4W-2922: GOVERNOR GP

4W-2922 GOVERNOR GP
S/N 48W34817-99999
PART OF 4W-7199 PUMP GP-GOV, FUEL INJ & TFR
i00107964 KEBP0105
4W2922 GOVERNOR GP Parts scheme 4W2922 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your PM-565 COLD PLANER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-3363 [1] HOUSING AS-GOVERNOR  
2. 9S-8001 [1] PLUG  
  4J-7533 [1] SEAL-O-RING  
3. 8M-8403 [1] SPRING-GUIDE  
4. 7E-8940 C [1] BUSHING  
5. 7E-8941 C [1] BUSHING  
6. 138-9507 [2] SEAL-LIP TYPE  
7. 8L-4308 [1] BOLT (5/16-18X2.75-IN)  
8. 9M-1974 C [5] WASHER-HARD (8.8X16X2-MM THK)  
9. 2B-2695 [1] BOLT (5/16-18X0.875-IN)  
10. 2P-8707 [1] PLATE AS-GOVERNOR  
11. 8L-4175 [1] DOWEL  
12. 0S-1594 [1] BOLT (3/8-16X1-IN)  
13. 1D-4540 [3] BOLT (5/16-18X2.75-IN)  
14. 1N-4656 [1] SHAFT  
15. 9N-1917 [1] COVER AS  
16. 3P-0009 [1] INSULATOR  
17. 9N-1916 [1] LEVER-SHUTOFF  
18. 5M-6228 [1] BEARING AS-NEEDLE  
19. 2A-0762 [2] BOLT (1/4-20X0.625-IN)  
20. 9N-2165 [1] LEVER-SOLENOID  
21. 1S-7336 [2] LOCK-BOLT  
22. 0S-1614 [2] BOLT (1/4-20X0.5-IN)  
23. 5P-0796 [2] SEAL-LIP TYPE  
24. 4N-0951 [1] SHAFT-SHUTOFF  
25. 1S-7984 [1] BUSHING  
26. 1K-4703 [1] WASHER (13.1X22.2X1.6-MM THK)  
27. 7N-7325 [1] SCREW-ADJUSTMENT (LOW-IDLE)  
28. 2J-0157 [2] SEAL-O-RING  
29. 8H-9204 [2] WASHER-FELT (19/32X7/8X5/16-IN THK)  
30. 3S-1494 [1] SCREW-ADJUSTMENT (HIGH-IDLE)  
31. 5L-8992 [1] COVER-ADJUSTMENT  
32. 5P-6945 [1] BOLT (1/4-20X1.125-IN)  
  4B-9747 [1] WASHER (0.266X0.375X0.031-IN THK)  
33. 8L-4155 [1] SETSCREW  
  9S-8748 [1] NUT-FULL (1/4-28-THD)  
34. 9M-4704 [1] BOLT (8-32X1-IN)  
35. 8L-4154 [1] COLLAR-LOAD STOP  
36. 7C-5279 C [1] COVER  
37. 4B-9365 C [2] BOLT (1/4-20X3-IN)  
  1B-4330 C [2] NUT (1/4-20-THD)  
  5P-0537 [4] WASHER-HARD (7.2X14.5X2-MM THK)  
38. 8L-3873 C [2] GASKET  
39. 2P-8669 [1] GASKET  
40. 2W-1491 [1] LEVER-CONTROL  
41. 9M-9788 [1] PLUNGER  
42. 7M-7316 [1] SPRING  
43. 5H-1351 [1] PIN-SPRING  
44. 2P-8679 [1] STRAINER AS  
45. 2P-8697 [1] GASKET  
46. 6N-3504 [1] SEAT-GOVERNOR SPRING  
47. 4N-1870 [1] GASKET-HOUSING  
48. 9S-8008 [1] PLUG (1-1/16-12-THD)  
  3D-2824 [1] SEAL-O-RING  
49. 9S-4182 [1] PLUG (7/16-20-THD)  
  3J-7354 [1] SEAL-O-RING  
50. 4W-2921 Y [1] PLATE GP-GOVERNOR ADAPTER  
51. 061-6708 [1] RING-RETAINING  
52. 6N-4158 [1] RING-GOVERNOR DRIVE  
53. 6N-4164 [1] SPRING  
54. 6N-4156 [1] RING-RETAINING  
55. 8H-9181 [1] SPRING-BUMPER  
56. 4W-7654 [1] BOLT (1/4-28X1.25-IN)  
57. 6N-8793 [1] SPRING  
58. 5L-8991 [1] GASKET-COVER  
59. 1B-9575 [1] BOLT (5/16-18X1.56-IN)  
60. 6N-4159 [1] DRIVE AS-GOVERNOR  
  2N-5626 [1] YOKE  
61. 6D-9953 [2] PIN-SPRING  
62. 6N-4460 [5] SPRING-LEAF  
63. 6N-4161 [1] COLLAR-GOVERNOR DRIVE  
  6N-4160 [1] PIN  
64. 3L-5987 CB [1] COVER  
  B   USE AS REQUIRED
  C   CHANGE FROM PREVIOUS TYPE
  Y   SEPARATE ILLUSTRATION
 

Information:

Truck Engine News
A Revised Special Instruction Provides Information on Service Replacement of the Turbocharger (for Turbocharged Engines Only) {1052}
2002/12/01
Accurate Diagnosis of Turbocharger Failure on Caterpillar Engines {1052, 1053}
2010/03/22
Engine News
A Revised Special Instruction Provides Information on Service Replacement of the Turbocharger (for Turbocharged Engines Only) {1052}
2002/12/01
Accurate Diagnosis of Turbocharger Failure on Caterpillar Engines {1052, 1053}
2010/03/22
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Special Instruction
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Instructions for the Service Replacement of the Turbochargers{1052}
Instructions for the Service Replacement of the Turbochargers{1052}
Installation Instructions for Turbochargers {1052}
Installation Instructions for Turbochargers {1052}
Proper Remanufactured Turbocharger Housing Adjustment and Alignment for Caterpillar Engines {1052, 1053}
Proper Remanufactured Turbocharger Housing Adjustment and Alignment for Caterpillar Engines {1052, 1053}
Specifications
Turbochargers
3408 VEHICULAR ENGINE
Air And Exhaust Lines
3408 VEHICULAR ENGINE
Inlet Air And Exhaust Lines
3408C ENGINE FOR CATERPILLAR BUILT MACHINES
Turbocharger
3408C ENGINE FOR CATERPILLAR BUILT MACHINES
Turbocharger
3408E and 3412E Engines for Caterpillar Built Machines
Reuse And Salvage Guidelines
Reuse and Salvage for Turbochargers {0760, 0767, 1052}
Reuse and Salvage for Turbochargers {0760, 0767, 1052}
Testing and Adjusting
Turbocharger - Inspect
3408E and 3412E Engines for Caterpillar Built Machines
Disassembly and Assembly
Turbocharger
SUPPLEMENT FOR 3408 ENGINE FOR PM-565 COLD PLANER
Turbocharger
3408 VEHICULAR ENGINE
Turbocharger - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines
Turbocharger - Assemble
3408E and 3412E Engines for Caterpillar Built Machines
Turbocharger - Remove
3408E and 3412E Engines for Caterpillar Built Machines
Turbocharger - Install
3408E and 3412E Engines for Caterpillar Built Machines
Service Magazine
Remove Piston Cooling Tubes Before Removal Of Pistons And Connecting Rods{1214,1218,1201,1225,1307}
1981/07/13
Exhaust Manifold And Air Lines Changes Prevent Broken Studs And Exhaust Leaks {1059,1061}
1981/09/14
Caterpillar Recommends Against The Use Of Alcohol Mist Injection Systems{1050,1250}
1982/06/28
Use Care When Handling Turbocharger Compressor Wheels{1052,1077}
1985/12/16
Special Instructions Packaged With Turbocharger Cartridge Repair Kits May Be Incorrect{1053}
1986/02/03
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Adapter For Disassembly And Assembly Of Turbocharger Cartridge{0620,1053}
1977/01/24
Changes To Retainer Nut Torque And Assembly Procedures For Turbocharger Compressor Wheels{0374,1052}
1977/02/28
Oversize Bearings For Turbocharger Center Housings Available {1053,1052}
1987/03/30
Stop Engine If There Is A Turbocharger Bearing Failure{1052,1318}
1987/04/06
Be Sure To Correctly Tighten Turbocharger Clamp Assemblies{1052}
1987/09/07
Silicone Grease Now Used In Seal Ring Groove In Turbochargers{1052,1053,1077}
1978/05/15
Improved Seal Rings For Turbine End Of Turbochargers{1052}
1978/07/03
Salvage Of Turbocharger Compressor Housing During Reconditioning{1052}
1978/10/09
Use Of 9S3265 Retaining Compound On Schwitzer Turbocharger Compressor Wheel Retainer Nuts{1052,1053}
1979/06/25
Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning{1053}
1979/08/20
Only One Dowel Pin Is Now Used To Hold The Thrust Bearing In The Correct Position{1053,1052}
1979/09/03
6V2055 High Vacuum Grease Gives Better Oil Seal {1052,1053,1077,0682}
1979/09/10
Different Thrust Bearing And Thrust Rings Now Used In Turbochargers{1052,1053}
1979/10/22
Compressor Nut Torque For Schwitzer Turbochargers{1052}
1993/07/26
New Seal Used In Air Lines Group {1058}
1994/03/21
A Revised Special Instruction Provides Information on Service Replacement of the Turbocharger (for Turbocharged Engines Only) {1052}
2002/12/09
Policy for Reusing the Turbocharger Turbine Housing {1065}
2003/07/14
Prevent the Possibility of Contamination in order to Ensure Longer Life of Turbochargers {1052}
2003/12/15
Magnetic Cover for the Turbocharger Oil Supply Line {1052, 1307}
2006/02/06
New Gaskets for the Turbocharger Oil Lines are Now Used {1052, 1307}
2005/06/27
Packaging the Turbocharger {1052}
2007/02/26
Troubleshooting the Wastegate Canister {1052, 1057}
2009/01/26
Accurate Diagnosis of Turbocharger Failure on Caterpillar Engines {1052, 1053}
2010/03/22
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}

Caterpillar Parts SIS Catalog PM-565 :

TURBOCHARGER GP
1W-0412 TURBOCHARGER GP
SHIELD GP-MANIFOLD
103-9412 SHIELD GP-MANIFOLD
MUFFLER GP
7R-7775 MUFFLER GP
MANIFOLD GP-EXHAUST
8N-0080 MANIFOLD GP-EXHAUST
LINES GP-AIR
1W-6843 LINES GP-AIR
LINES GP-AIR
107-9375 LINES GP-AIR
6I-3833 KIT-AIR CLEANER
EXTENSION GP-EXHAUST
1W-4751 EXTENSION GP-EXHAUST
CONTROL GP-GOVERNOR
1G-8626 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
3N-7741 CONTROL GP-GOVERNOR
DRIVE GP-GOVERNOR & FUEL PUMP
9N-3959 DRIVE GP-GOVERNOR & FUEL PUMP
DRIVE GP-TACHOMETER
2W-2094 DRIVE GP-TACHOMETER
FASTENER GP-FUEL INJ PUMP
9Y-3764 FASTENER GP-FUEL INJ PUMP
FILTER & LINES GP-FUEL
7R-9855 FILTER & LINES GP-FUEL
FILTER GP-FUEL
4N-1981 FILTER GP-FUEL
FILTER GP-PRIMARY FUEL
6N-1044 FILTER GP-PRIMARY FUEL

Truck sale:

CATERPILLAR PM-565 1995
 
CATERPILLAR PM-565 1995
- COLD PLANERS
ATLANTIC CAT
175 Akerley Blvd - Dartmouth - Nova Sc
2003 CAT PM-565
Call 
2003 CAT PM-565

Earth Sales Group
Sachse, Texas
1993 CAT PM-565
USD $55,000 
1993 CAT PM-565

Earth Sales Group
Sachse, Texas
1993 CAT PM-565
USD $65,000 
1993 CAT PM-565

PARK EAST SALES
Troy, New York
 
USD $41,000 
1997 CAT PM-565

Big D Heavy Equipment LLC
Dallas, Texas
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.