ELECTRICAL AND STARTING SYSTEM
STARTING MOTOR GPSWITCH GP
WARNING GP
WIRING GP
POWER TRAIN
AXLE GPELECTRICAL AND STARTING SYSTEM
STARTING MOTOR GP
#KEBP02350120
207-1517: STARTING MOTOR GP-ELECTRIC
207-1517 STARTING MOTOR GP-ELECTRIC
S/N 4TF44156-UP
24 VOLT
FIELD REPLACEMENT FOR 207-1511 STARTING MOTOR GP-ELECTRIC
S/N 4TF44156-UP
24 VOLT
FIELD REPLACEMENT FOR 207-1511 STARTING MOTOR GP-ELECTRIC
For full view, you need register
Parts for your CS-573D VIBRATORY COMPACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8T-9884 | [1] | KIT-INSULATOR (STARTING MOTOR) | |
| (INCLUDES INSULATORS & BUSHING) | ||||
| 2. | 106-7149 | [1] | HOUSING AS | |
| 3. | 102-9863 | [1] | TERMINAL AS | |
| 4. | 6V-8188 | [4] | NUT (1/2-13-THD) | |
| 5. | 7X-0562 | [4] | WASHER-HARD (13.5X19X0.8-MM THK) | |
| 6. | 3E-7853 | [1] | TERMINAL | |
| 7. | 9X-4821 | [1] | PLATE AS | |
| 8. | 3E-7852 | [1] | COIL-STARTING MOTOR | |
| 9. | 7T-3454 | [1] | INSULATOR | |
| 10. | 9X-4271 | [1] | CONNECTOR | |
| 11. | 7T-3451 | [1] | KIT-INSULATOR (STARTING MOTOR) | |
| (INCLUDES INSULATORS & GROMMET) | ||||
| 12. | 8T-8569 | [1] | INSULATOR-TERMINAL | |
| 13. | 5S-7349 | [4] | BOLT (1/4-20X0.5-IN) | |
| 14. | 8T-4205 | [4] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 15. | 7X-1950 | [4] | SHOE-POLE | |
| 16. | 3E-7861 | [1] | KIT-LEVER (STARTING MOTOR) | |
| (INCLUDES LEVER AS, SHAFT AS, GASKET, O-RINGS, RING & NUT) | ||||
| 17. | 3R-8797 | [8] | SCREW & WASHER AS (3/8-24X0.72-IN) | |
| 18. | 3E-7855 | [1] | ARMATURE AS-STARTER (24-VOLT) | |
| 19. | 7X-1952 | [1] | HOUSING AS-LEVER | |
| 20. | 4M-1831 | [1] | PLUG-LEVER HOUSING | |
| 21. | 7L-2894 | [1] | GASKET | |
| 22. | 0S-1597 | [5] | BOLT (1/4-28X1-IN) | |
| 23. | 3E-7857 | [1] | DRIVE AS-STARTING MOTOR | |
| 24. | 3E-7858 | [1] | HOUSING AS | |
| 25. | 7X-3373 | [6] | BOLT (5/16-18X0.88-IN) | |
| 26. | 206-8784 | [1] | KIT-SOLENOID (24-VOLT) | |
| (INCLUDES SOLENOID AS, BOLT, CONNECTOR & NUTS) | ||||
| 27. | 6V-8378 | [2] | NUT (10-32-THD) | |
| 28. | 8F-1434 | [1] | LOCKWASHER | |
| 29. | 8T-0328 | [2] | WASHER-HARD (5.5X10X1-MM THK) | |
| 30. | 9X-4824 | [1] | COVER-STARTING MOTOR | |
| 31. | 9X-4825 | [1] | KIT-BRUSH (24-VOLT) | |
| (INCLUDES O-RING, SCREWS, BRUSHES & SPRINGS) | ||||
| AVAILABLE REPAIR KIT(S): | ||||
| 3E-7860 | [1] | KIT-BUSHING (STARTING MOTOR) | ||
| (INCLUDES BUSHINGS, PLUGS, CUPS, SEAL, NUT, O-RINGS, GASKET, SPACER, WASHERS & SCREW ASSEMBLIES) | ||||
#KEBP02350121
6V-5720: STARTING MOTOR GP-ELECTRIC
6V-5720 STARTING MOTOR GP-ELECTRIC
S/N 4TF44156-UP
24 VOLT
PART OF 104-7040 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@106-8558@@@@@
CANNOT BE USED WITH WET FLYWHEEL HOUSING
S/N 4TF44156-UP
24 VOLT
PART OF 104-7040 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@106-8558@@@@@
CANNOT BE USED WITH WET FLYWHEEL HOUSING
For full view, you need register
Parts for your CS-573D VIBRATORY COMPACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 4M-1828 | [1] | RETAINER-SPRING | |
| 2. | 036-9821 | [1] | WASHER | |
| 3. | 7T-3269 | [1] | BOOT | |
| 4. | 8T-9884 | [1] | KIT-INSULATOR (STARTING MOTOR) | |
| 5. | 9M-7609 | [1] | SPRING (SHIFT LEVER) | |
| 6. | 4M-1827 | [1] | RETAINER-SPRING | |
| 7. | 4M-1831 | [1] | PLUG-LEVER HOUSING | |
| 8. | 7L-2894 | [1] | GASKET | |
| 9. | 9X-4824 | [1] | COVER-STARTING MOTOR | |
| 10. | 7X-1953 | [1] | DRIVE AS-MOTOR | |
| 11. | 7X-0562 | [4] | WASHER-HARD (13.5X19X0.8-MM THK) | |
| 12. | 6V-8188 | [4] | NUT (1/2-13-THD) | |
| 13. | 4B-2049 | [2] | NUT (10-32-THD) | |
| 14. | 8T-0328 | [2] | WASHER-HARD (5.5X10X1-MM THK) | |
| 15. | 8F-1434 | [1] | LOCKWASHER | |
| 16. | 2H-3429 | [1] | RING-RETAINING | |
| 17. | 9X-4823 | [1] | SOLENOID AS | |
| 18. | 9X-4821 | [1] | PLATE AS | |
| 19. | 7X-1951 | [1] | ARMATURE AS (24-VOLT) | |
| 20. | 5S-7349 | [4] | BOLT (1/4-20X0.5-IN) | |
| 21. | 8T-4205 | [4] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 22. | 3E-7853 | [1] | TERMINAL | |
| 23. | 102-9863 | [1] | TERMINAL AS | |
| 24. | 106-7149 | [1] | HOUSING AS | |
| 25. | 9X-4822 | [1] | COIL AS | |
| 26. | 7T-3454 | [1] | INSULATOR | |
| 27. | 9X-4271 | [1] | CONNECTOR | |
| 28. | 8T-8569 | [1] | INSULATOR-TERMINAL | |
| 29. | 7T-3451 | [1] | KIT-INSULATOR (STARTING MOTOR) | |
| 30. | 7X-1950 | [4] | SHOE-POLE | |
| 31. | 3F-0379 | [8] | SCREW-POLE SHOE (3/8-24-THD) | |
| 32. | 7X-1952 | [1] | HOUSING AS-LEVER | |
| 33. | 036-9823 | [5] | BOLT (1/4-28X1-IN) | |
| 34. | 7X-1954 | [1] | HOUSING AS-DRIVE | |
| 35. | 7X-3373 | [6] | BOLT (5/16-18X0.88-IN) | |
| 36. | 7T-3270 | [1] | PLUNGER AS | |
| AVAILABLE REPAIR KIT(S): | ||||
| 7X-1958 | [1] | KIT-LEVER (STARTING MOTOR) | ||
| (INCLUDES LEVER AS, SHAFT AS, GASKET, O-RINGS, RINGS, STOP & NUT) | ||||
| 9X-4270 | [1] | KIT-BUSHING (STARTING MOTOR) | ||
| (INCLUDES BUSHINGS, SEAL, NUT, O-RINGS, CUPS, SPACER, STOP, PLUGS, GASKET, WASHERS, RING & SCREW AS) | ||||
| 9X-4825 | [1] | KIT-BRUSH (24-VOLT) | ||
| (INCLUDES BRUSHES, O-RING, SCREWS & SPRINGS) | ||||
#KEBP02350122
7N-0718: SWITCH GP-DISCONNECT
7N-0718 SWITCH GP-DISCONNECT -BATTERY
S/N 2YZ1-UP
PART OF 156-6314 BATTERY & WIRING GP
S/N 2YZ1-UP
PART OF 156-6314 BATTERY & WIRING GP
For full view, you need register
#KEBP02350123
167-0138: SWITCH GP-MAGNETIC
167-0138 SWITCH GP-MAGNETIC
S/N 2YZ1-UP
24-VOLT
PART OF 143-5933 PANEL GP-CONTROL, 143-5921 PANEL GP-INSTRUMENT
ALSO AN ATTACHMENT
S/N 2YZ1-UP
24-VOLT
PART OF 143-5933 PANEL GP-CONTROL, 143-5921 PANEL GP-INSTRUMENT
ALSO AN ATTACHMENT
For full view, you need register
Parts for your CS-573D VIBRATORY COMPACTOR:
CATERPILLAR SIS#KEBP02350124
149-6474: WARNING GP-BACKUP
For full view, you need register
#KEBP02350125
155-6420: WIRING GP-AIR CONDITIONER
155-6420 WIRING GP-AIR CONDITIONER
S/N 2YZ1-UP
PART OF 155-6359 AIR CONDITIONER AR
AN ATTACHMENT
S/N 2YZ1-UP
PART OF 155-6359 AIR CONDITIONER AR
AN ATTACHMENT
For full view, you need register
Parts for your CS-573D VIBRATORY COMPACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 106-8704 | [1] | SUPPRESSOR AS-ARC | |
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [2] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 2. | 116-0118 | [2] | CLIP | |
| 3. | 139-2270 | [1] | HARNESS AS-WIRING (AIR CONDITIONER COMPRESSOR) | |
| 8T-8729 | [2] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 155-2270 | [3] | KIT-CONNECTING PLUG (2-PIN) | ||
| (EACH INCLUDES PLUG AS, WEDGE & INTERFACE SEAL) | ||||
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8730 | [6] | SOCKET-CONNECTOR (16-GA TO 18-GA) | ||
| 4. | 4P-7581 | [1] | CLIP (LADDER) | |
| 5. | 8T-4133 M | [1] | NUT (M10X1.5-THD) | |
| 6. | 8T-4121 | [2] | WASHER-HARD (11X21X2.5-MM THK) | |
| 7. | 8T-4195 M | [1] | BOLT (M10X1.5X30-MM) | |
| 8. | 3S-2093 | [19] | STRAP-CABLE | |
| 9. | 7K-1181 | [1] | STRAP-CABLE | |
| M | METRIC PART | |||
#KEBP02350126
143-5923: WIRING GP-CAB
For full view, you need register
Parts for your CS-573D VIBRATORY COMPACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 152-9802 | [1] | HARNESS AS-CAB | |
| 102-8804 | [1] | KIT-RECEPTACLE (4-PIN) | ||
| 102-8801 | [1] | KIT-RECEPTACLE (12-PIN) | ||
| (EACH KIT INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [13] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8730 | [14] | SOCKET-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8737 | [5] | PLUG-SEAL | ||
| 9X-1056 | [2] | TERMINAL-RECEPTACLE (14-GA TO 16-GA) | ||
| 155-2271 | [1] | KIT-CONNECTING PLUG (4-PIN) | ||
| 155-2274 | [2] | KIT-CONNECTING PLUG (6-PIN) | ||
| (EACH KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL) | ||||
| 2. | 3S-2093 | [34] | STRAP-CABLE | |
#KEBP02350127
149-6478: WIRING GP-MACHINE
For full view, you need register
Parts for your CS-573D VIBRATORY COMPACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 121-6815 | [1] | PLATE | |
| 2. | 103-4977 | [1] | SWITCH AS-PRESSURE (ENGINE OIL) | |
| 8T-8729 | [1] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 3. | 107-0611 | [1] | SWITCH AS-PRESSURE (ENGINE OIL) | |
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [2] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 4. | 3K-0360 | [3] | SEAL-O-RING | |
| 5. | 6L-3483 | [3] | COVER-TERMINAL | |
| 6. | 8T-8799 | [2] | BOOT (RED) | |
| 7. | 4P-8134 | [10] | CLIP (LADDER) | |
| 8. | 4P-7581 | [5] | CLIP (LADDER) | |
| 9. | 9X-0506 | [8] | TIE | |
| 10. | 8T-4121 | [4] | WASHER-HARD (11X21X2.5-MM THK) | |
| 11. | 5P-4115 | [5] | WASHER-HARD (7.2X19X2-MM THK) | |
| 12. | 8T-4199 M | [1] | BOLT (M8X1.25X12-MM) | |
| 13. | 5P-9617 | [2] | ADAPTER | |
| 14. | 5P-5528 | [2] | BUSHING-REDUCER | |
| 15. | 3P-1932 | [1] | ADAPTER | |
| 16. | 3B-6552 | [1] | ELBOW-PIPE | |
| 17. | 3J-1907 | [2] | SEAL-O-RING | |
| 18. | 3J-7354 | [3] | SEAL-O-RING | |
| 19. | 8C-3445 | [1] | CAP-DUST | |
| 20. | 8C-3446 | [1] | VALVE-SAMPLING | |
| 21. | 8T-4137 M | [2] | BOLT (M10X1.5X20-MM) | |
| 22. | 139-2786 | [1] | HARNESS AS-POWER | |
| 155-2270 | [9] | KIT-CONNECTING PLUG (2-PIN) | ||
| 155-2260 | [4] | KIT-CONNECTING PLUG (3-PIN) | ||
| 155-2271 | [2] | KIT-CONNECTING PLUG (4-PIN) | ||
| 7X-6222 | [1] | PLUG AS-CONNECTOR (24-PIN) | ||
| 8T-8737 | [3] | PLUG-SEAL | ||
| 127-5483 | [1] | PLUG AS-CONNECTOR (1-PIN) | ||
| 127-5484 | [2] | RECEPTACLE AS-CONNECTOR (1-PIN) | ||
| 129-7163 | [1] | PLUG AS-CONNECTOR (1-PIN) | ||
| 129-7164 | [1] | RECEPTACLE AS-CONNECTOR (1-PIN) | ||
| 23. | 116-0118 | [7] | CLIP | |
| 24. | 3S-2093 | [14] | STRAP-CABLE | |
| 25. | 8T-4136 M | [2] | BOLT (M10X1.5X25-MM) | |
| 26. | 9X-8256 | [8] | WASHER (6.6X12X2-MM THK) | |
| 27. | 8T-4138 M | [4] | BOLT (M6X1X20-MM) | |
| 28. | 4Y-7948 | [1] | TIMER AS-INLET HEATER | |
| 8T-8729 | [4] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 102-8804 | [1] | KIT-RECEPTACLE (4-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 29. | 5C-2890 M | [4] | NUT (M6X1-THD) | |
| 30. | 118-3534 | [1] | SWITCH GP-MAGNETIC (24-VOLT)(START AID RELAY) | |
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 5C-2890 M | [2] | NUT (M6X1-THD) | ||
| 8T-8729 | [2] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 9X-1386 BE | SLEEVE | |||
| 31. | 6V-7357 M | [2] | BOLT (M6X1X25-MM) | |
| 32. | 8T-4896 | [2] | WASHER-HARD (10.2X18.5X2.5-MM THK) | |
| 33. | 5M-3062 | [2] | BOLT (3/8-16X0.75-IN) | |
| 34. | 2V-6166 | [1] | CABLE AS | |
| 35. | 7K-1181 | [10] | STRAP-CABLE | |
| 36. | 110-2706 | [1] | STRAP AS-GROUND | |
| 37. | 8T-4189 M | [2] | BOLT (M8X1.25X20-MM) | |
| 38. | 8T-4908 M | [1] | BOLT (M8X1.25X25-MM) | |
| 39. | 3E-6449 | [1] | SWITCH AS-TEMPERATURE (COOLANT) | |
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [2] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 40. | 3E-6451 | [1] | SWITCH GP-TEMPERATURE (COOLANT) | |
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [2] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 41. | 5P-4116 | [6] | WASHER-HARD (8.8X20.5X2-MM THK) | |
| 42. | 5P-9299 | [2] | CLIP (LOOP) | |
| 43. | 8T-7547 M | [2] | BOLT (M8X1.25X30-MM) | |
| 44. | 7V-5626 | [2] | CLAMP | |
| 45. | 4M-5282 | [2] | BOLT (1/4-20X1.5-IN) | |
| 46. | 7V-5628 | [1] | PLATE (TOP) | |
| B | USE AS REQUIRED | |||
| E | ORDER BY THE CENTIMETER | |||
| M | METRIC PART | |||
#KEBP02350128
177-5149: AXLE & MTG GP-DRIVE
For full view, you need register
Parts for your CS-573D VIBRATORY COMPACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 7X-0510 | [6] | WASHER-HARD (15.5X29X3-MM THK) | |
| 2. | 8S-4734 | [6] | BOLT (9/16-12X2-IN) | |
| 3. | 136-8873 Y | [1] | AXLE GP | |
| 4. | 155-6744 Y | [1] | PLANETARY GP-FINAL DRIVE | |
| 5. | 6S-3002 | [1] | SEAL-O-RING | |
| 6. | 7X-2570 M | [8] | BOLT (M20X2.5X220-MM) | |
| 7. | 8T-4123 | [16] | WASHER (3.62X5.75X0.375-MM THK) | |
| 8. | 8T-4131 M | [8] | NUT (M20X2.5-THD) | |
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#KEBP02350129
136-8873: AXLE GP
For full view, you need register
Parts for your CS-573D VIBRATORY COMPACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 055-1260 | [2] | HOUSING-BRAKE (OUTER)(OUTER) | |
| 2. | 055-1259 | [1] | HOUSING-BRAKE (INNER) | |
| 3. | 9X-8876 | [12] | BOLT (1/2-13X4.75-IN) | |
| 4. | 8M-3171 | [4] | NUT (1/2-20-THD) | |
| 5. | 055-1258 | [1] | HOUSING-BRAKE (RH)(INNER) | |
| 6. | 9R-2474 | [2] | PIN | |
| 7. | 9R-2412 | [4] | STUD | |
| 8. | 133-7234 | [8] | DISC-FRICTION | |
| 9. | 102-8458 | [4] | DISC | |
| 10. | 102-8457 | [2] | DISC | |
| 11. | 9R-2472 | [8] | SPRING | |
| 12. | 9R-2473 | [12] | BALL | |
| 13. | 055-1255 | [4] | PIN-PIVOT | |
| 14. | 055-1256 | [4] | LINK-PLAIN | |
| 15. | 055-1244 | [2] | ROD-BRAKE CONTROL | |
| 16. | 9R-6573 | [2] | SEAL AS-BOOT | |
| 17. | 9R-2475 | [2] | PIN | |
| 18. | 3B-4617 | [2] | PIN-COTTER | |
| 19. | 1B-4430 | [4] | NUT-JAM (1/2-20-THD) | |
| 20. | 9R-2427 B | [1] | SHIM (0.965-MM THK) | |
| 9R-2428 B | [1] | SHIM (1.118-MM THK) | ||
| 9R-2429 B | [1] | SHIM (1.27-MM THK) | ||
| 9R-2430 B | [1] | SHIM (1.422-MM THK) | ||
| 9R-2431 B | [1] | SHIM (1.575-MM THK) | ||
| 9R-2432 B | [1] | SHIM (1.727-MM THK) | ||
| 9R-2433 B | [1] | SHIM (1.88-MM THK) | ||
| 9R-2434 B | [1] | SHIM (2.032-MM THK) | ||
| 21. | 9R-2435 B | [2] | SPACER (22.86X53.85X1.25-MM THK) | |
| 9R-2436 B | [2] | SPACER (22.86X53.85X1.35-MM THK) | ||
| 9R-2437 B | [2] | SPACER (22.86X53.85X1.45-MM THK) | ||
| 9R-2438 B | [2] | SPACER (22.86X53.85X1.55-MM THK) | ||
| 9R-2439 B | [2] | SPACER (22.86X53.85X1.65-MM THK) | ||
| 9R-2440 B | [2] | SPACER (22.86X53.85X1.75-MM THK) | ||
| 9R-2441 B | [2] | SPACER (22.86X53.85X1.85-MM THK) | ||
| 9R-2442 B | [2] | SPACER (22.86X53.85X1.96-MM THK) | ||
| 9R-2443 B | [2] | SPACER (22.86X53.85X2.06-MM THK) | ||
| 9R-2444 B | [2] | SPACER (22.86X53.85X2.16-MM THK) | ||
| 9R-2445 B | [2] | SPACER (22.86X53.85X2.26-MM THK) | ||
| 22. | 9R-2425 | [2] | WASHER (23.088X69.6X9.52-MM THK) | |
| 23. | 9R-2466 M | [2] | BOLT (7/8-14X2.2-IN) | |
| 24. | 9R-2426 | [2] | LOCK | |
| 25. | 9R-2414 | [2] | GEAR (56-TEETH) | |
| 26. | 9R-2495 | [1] | SEAL | |
| 27. | 8S-9151 | [2] | CUP-BEARING | |
| 28. | 2A-4576 | [1] | CUP-BEARING (TAPERED ROLLER) | |
| 29. | 5L-9656 | [1] | CONE-BEARING (TAPERED ROLLER) | |
| 30. | 2M-2570 | [12] | LOCKNUT (1/2-20-THD) | |
| 31. | 144-5392 | [1] | BLOCK-THRUST | |
| 32. | 3B-4507 | [2] | LOCKWASHER | |
| 33. | 0T-0318 | [2] | BOLT (7/16-14X1-IN) | |
| 34. | 7R-8971 | [1] | GEAR SET | |
| 35. | 9R-6671 M | [12] | BOLT (1/2-20X1.62-IN) | |
| 36. | 9R-2424 | [2] | GEAR (16-TEETH) | |
| 37. | 163-0053 Y | [1] | DIFFERENTIAL GP | |
| 38. | 2S-0479 | [1] | CONE-BEARING (TAPERED ROLLER) | |
| 39. | 2S-0480 | [1] | CUP-TAPERED ROLLER | |
| 40. | 102-8469 | [2] | PLUG | |
| 41. | 102-8476 | [2] | SCREW-PURGE | |
| 42. | 176-2570 Y | [1] | CYLINDER GP-BRAKE | |
| 43. | 208-8890 | [1] | HOUSING-AXLE (RH) | |
| 208-8891 | [1] | HOUSING-AXLE (LH) | ||
| 44. | 102-8466 | [4] | BOLT-FLANGE HEAD | |
| 45. | 102-8453 | [2] | U-BOLT | |
| 46. | 9S-1354 | [8] | NUT (5/8-18-THD) | |
| 47. | 102-8463 | [4] | WASHER | |
| 48. | 102-8454 | [2] | BRACKET | |
| 49. | 9R-2413 | [8] | STUD | |
| 50. | 102-8465 | [4] | NUT-FLANGE | |
| 51. | 3K-6060 | [4] | LOCKNUT (3/8-16-THD) | |
| 52. | 102-8461 B | [2] | SHIM | |
| 53. | 176-2427 | [2] | SPRING | |
| 54. | 102-8477 | [2] | STOP | |
| 55. | 102-8467 | [2] | RETAINER | |
| 56. | 6V-7687 M | [2] | LOCKNUT (M12X1.75-THD) | |
| 57. | 102-8460 | [2] | SPRING | |
| 58. | 102-8464 | [2] | PLUG-END | |
| 59. | 7R-8978 | [1] | RING | |
| 60. | 179-7021 | [2] | LOCKNUT | |
| 61. | 7R-8977 | [1] | WASHER | |
| 62. | 7R-8975 | [1] | WASHER | |
| 63. | 7T-6653 | [1] | CONE-BEARING (TAPERED ROLLER) | |
| 64. | 3N-6408 | [1] | CUP-BEARING (TAPERED ROLLER) | |
| 65. | 7R-8974 | [1] | RETAINER AS | |
| 66. | 9R-2512 | [1] | SEAL | |
| 67. | 4K-5843 | [1] | CUP-BEARING (TAPERED ROLLER) | |
| 68. | 7T-6654 | [1] | CONE-BEARING (TAPERED ROLLER) | |
| 69. | 7R-8970 | [1] | BEARING | |
| 70. | 9R-2494 | [1] | RING | |
| 71. | 5F-5434 | [1] | VALVE AS-VENT | |
| 72. | 1B-5174 | [2] | PLUG-PIPE | |
| 73. | 2B-7408 | [1] | PLUG-PIPE | |
| 74. | 144-7225 | [1] | HOUSING-DIFFERENTIAL | |
| 75. | 9R-6602 | [1] | PLUG-MAGNETIC | |
| 76. | 118-5837 | [2] | SHAFT AS | |
| (EACH INCLUDES) | ||||
| 76A. | 9R-5219 | [8] | BOLT-SPECIAL | |
| 77. | JZ | [1] | RING | |
| 78. | 118-5839 | [2] | SEAL-REAR AXLE | |
| 79. | 030-1957 | [2] | CONE-BEARING (TAPERED ROLLER) | |
| 80. | 6Y-7652 | [2] | CUP-BEARING (TAPERED ROLLER) | |
| 81. | 9X-8883 | [1] | BOLT (5/8-11X2.75-IN) | |
| 82. | 7R-8983 | [1] | PLUG | |
| 83. | 186-4117 | [2] | CARRIER AS | |
| (EACH INCLUDES) | ||||
| 83A. | 9R-2420 | [1] | RETAINER | |
| 83B. | 186-4118 | [3] | GEAR-PLANETARY (20-TEETH) | |
| 83C. | 9R-2417 | [3] | WASHER (33.07X48.38X1.06-MM THK) | |
| 83D. | 9R-2419 | [3] | KIT-BEARING | |
| 83E. | 7T-6652 | [1] | CONE-BEARING (TAPERED ROLLER) | |
| 83F. | 9R-2421 | [3] | SHAFT | |
| 83G. | 9R-2418 | [6] | WASHER (32.94X57.21X0.78-MM THK) | |
| 84. | JZ | [1] | WASHER | |
| 85. | JZ | [1] | CAP | |
| 86. | JZ | [1] | CAP | |
| 87. | JZ | [1] | PISTON | |
| 88. | JZ | [1] | CYLINDER | |
| 89. | JZ | [3] | RING | |
| 90. | JZ | [1] | GASKET | |
| 91. | JZ | [2] | RING | |
| 92. | JZ | [2] | RING | |
| 93. | JZ | [1] | RING | |
| AVAILABLE REPAIR KIT(S): | ||||
| 102-8595 J | [1] | KIT-CYLINDER | ||
| B | USE AS REQUIRED | |||
| J | KIT MARKED J SERVICES PART(S) MARKED J | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
| Z | NOT SERVICED SEPARATELY | |||
Information:
ELECTRICAL AND STARTING SYSTEM
STARTING MOTOR GP
Truck Engine News
Engine News
Special Instruction
Installation of New Shift Lever Assembly for All Starter Motors {1453}
Installation of New Shift Lever Assembly for All Starter Motors {1453}
Installation of New Shift Lever Assembly for All Starter Motors {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Replace Armature of Starter Motor On All Cat<SUP>®</SUP> Products {1408, 1450, 1453}
Procedure to Replace Armature of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Armature of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat<SUP>®</SUP> Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat<SUP>®</SUP> Products {1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat® Products {1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat® Products {1453}
Technical Information Bulletin
Some Remanufactured Electric Starter Groups May Have An Incorrect Nose Housing
Some Remanufactured Electric Starter Groups May Have An Incorrect Nose Housing
Some Remanufactured Electric Starter Groups May Have An Incorrect Nose Housing
Specifications
Systems Operation
Testing and Adjusting
Troubleshooting
Engine Does Not Crank with Starting Motor On and Pinion Engaging Ring Gear
37-MT, 41-MT, and 42-MT Series Starting Motors
37-MT, 41-MT, and 42-MT Series Starting Motors
Disassembly and Assembly
Electric Starting Motor - Remove and Install
3114, 3116, and 3126 Engines for Caterpillar Built Machines
3114, 3116, and 3126 Engines for Caterpillar Built Machines
Service Magazine
