141-9440 WIRING GP-MACHINE S/N 8GS1-UP PART OF 140-1083 ELECTRICAL AR PM-565B COLD PLANER

ELECTRICAL AND STARTING SYSTEM

WIRING GP

0. 141-9440 WIRING GP-
1. 143-3633 WIRING GP-
2. 143-3633 WIRING GP-
3. 133-4060 WIRING GP-
4. 109-0401 WIRING GP-

POWER TRAIN

HYDRAULIC AR-PROPEL

5. 142-9932 HYDRAULIC

LINES GP-HYDROSTATIC

6. 142-9940 LINES GP-H

MOTOR GP

7. 142-9933 MOTOR & MT

DRIVE GP-FINAL

8. 142-9944 PLANETARY
9. 168-6959 PLANETARY
0. INFORMATION

COLD PLANER PM-565B COLD PLANER 8GS
PM-565B Cold Planer 8GS00001-UP (MACHINE) POWERED BY 3408C Engine KEBP4132 PM-565B 8GS (1997)

ELECTRICAL AND STARTING SYSTEM

WIRING GP

121-4082 WIRING GP-ENGINE ELECTRONIC

141-2462 WIRING GP-FRONT

141-9440 WIRING GP-MACHINE

143-3633 WIRING GP-REAR

133-4060 WIRING GP-ROTOR

#KEBP41320230

141-9440: WIRING GP-MACHINE

WIRING GP-MACHINE

141-9440 WIRING GP-MACHINE
S/N 8GS1-UP
PART OF 140-1083 ELECTRICAL AR

i00502730 KEBP4132

For full view, you need register

Parts for your PM-565B COLD PLANER:

CATERPILLAR SIS

Part No	Qty	Parts name
201-6947 Y	[1]	WIRING GP-CONVEYOR
133-4058 Y	[1]	WIRING GP-CENTER
141-2462 Y	[1]	WIRING GP-FRONT
143-3633 Y	[1]	WIRING GP-REAR
Y		SEPARATE ILLUSTRATION

#KEBP41320231

143-3633: WIRING GP-REAR

WIRING GP-REAR

143-3633 WIRING GP-REAR
S/N 8GS1-264
PART OF 141-9440 WIRING GP-MACHINE

i00505162 KEBP4132

For full view, you need register

Parts for your PM-565B COLD PLANER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	101-8562	[1]	HARNESS AS-SENSOR (TRAVEL SPEED)
	3S-2093	[2]	STRAP-CABLE
	5P-1520 E		HOSE (216-CM)
	8T-8731	[2]	PLUG-CONNECTOR (3-PIN)
2.	6D-3479	[3]	CLIP
3.	9X-1439 Y	[4]	LAMP GP-FLOOD (24-VOLT)
4.	8T-9378	[2]	BOLT (3/8-16X4-IN)
5.	8T-4896	[7]	WASHER-HARD (10.2X18.5X2.5-MM THK)
6.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
7.	8T-4121	[9]	WASHER-HARD (11X21X2.5-MM THK)
8.	7T-0969	[1]	HORN AS (24-VOLT, LOW TONE)
	8C-7581 M	[2]	SCREW-MACHINE (M4X0.7X8-MM)
	9B-7233	[2]	LOCKWASHER
	096-6166	[2]	WASHER-HARD (4.5X9X1-MM THK)
9.	7K-1181 BE		STRAP-CABLE
10.	5P-6264	[1]	GROMMET
11.	4D-1326	[1]	LOCKWASHER (EXTERNAL TOOTH)
12.	3T-1815	[1]	ALARM GP
13.	3S-2093	[21]	STRAP-CABLE
14.	8T-4133 M	[6]	NUT (M10X1.5-THD)
15.	4D-8123	[1]	CLIP
16.	134-1840	[1]	HARNESS AS-REAR
	8T-8799	[1]	BOOT (RED)
	9X-0141	[2]	PLUG AS-CONNECTOR (40-PIN)
	9X-4813	[2]	RECEPTACLE AS-CONNECTOR (3-PIN)
	9X-7147	[1]	PLUG AS-CONNECTOR (40-PIN)
	8C-3056 BE		CABLE (2-GA, RED)
	7N-9738	[1]	HOUSING-RECEPTACLE (14-GA TO 18-GA)
	7X-6222	[1]	PLUG AS-CONNECTOR (24-PIN)
	155-2270	[51]	KIT-CONNECTING PLUG (2-PIN)
	155-2260	[5]	KIT-CONNECTING PLUG (3-PIN)
	102-8803	[4]	KIT-RECEPTACLE (3-PIN)
	155-2271	[2]	KIT-CONNECTING PLUG (4-PIN)
	3E-7996	[10]	PLUG-CONNECTOR (6-PIN)
17.	9X-0941	[3]	LOCKNUT (1/2-13-THD)
18.	8T-4223	[3]	WASHER-HARD (13.5X25.5X3-MM THK)
19.	3E-7675	[1]	SWITCH GP-PRESSURE (SYSTEM HYDRAULICS)
20.	3E-7675	[1]	SWITCH GP-PRESSURE (TRACK BRAKE)
			(EACH AS INCLUDES)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	8T-8729	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
21.	5P-6944	[1]	ADAPTER
22.	3K-0360	[2]	SEAL-O-RING
23.	3E-8700 Y	[1]	SENSOR GP-TEMPERATURE (HYDRAULIC OIL)
23A.	3E-8700 Y	[1]	SENSOR GP-TEMPERATURE (CLUTCH OIL)
24.	3J-1907	[6]	SEAL-O-RING
25.	3S-8664	[1]	CLIP (LOOP)
26.	0L-1407	[1]	GROMMET
27.	1H-3338	[6]	LOCKWASHER (EXTERNAL TOOTH)
28.	6V-3342	[1]	ELBOW-PIPE
29.	134-1419	[1]	BLOCK
30.	3E-6466 Y	[2]	LAMP GP-SIGNAL (24-VOLT)
31.	142-3010	[1]	ENCLOSURE AS-REAR
	5D-9629	[2]	ROD
32.	142-3009	[1]	ENCLOSURE AS-REAR
	5D-9629	[2]	ROD
33.	3E-7842	[1]	RESISTOR AS
34.	116-5270	[2]	LAMP (24-VOLT)
35.	3E-9860	[17]	LOCKNUT (5/16-18-THD)
36.	7J-9108	[2]	SEAL-O-RING
37.	116-5273	[2]	KNOB (RED)
38.	145-4876 Y	[1]	SENSOR GP-PRESSURE ELECTRONIC
39.	9X-5272 Y	[1]	SENSOR GP-PRESSURE
40.	3K-6060	[2]	LOCKNUT (3/8-16-THD)
41.	8T-4205	[3]	WASHER-HARD (7.2X14.5X2-MM THK)
42.	154-6464	[1]	SWITCH AS-PRESSURE (HYDRAULIC OIL)
43.	7X-0280	[1]	BOLT (5/16-18X5.0-IN)
44.	1G-9089	[1]	CHAIN
45.	4L-6454	[2]	BOLT (3/8-16X1-IN)
46.	5P-8167	[1]	BOLT (3/8-16X0.625-IN)
47.	4M-6425	[4]	BOLT (5/16-18X1-IN)
48.	4P-7581	[3]	CLIP (LADDER)
49.	4S-4455	[2]	CLIP
50.	9N-7446	[8]	LOCKNUT (4-40-THD)
51.	5P-0765 E		HOSE (51-CM)
52.	5P-1079	[4]	SCREW-MACHINE (4-40X0.875-IN)
53.	8T-4224	[30]	WASHER-HARD (8.8X16X2-MM THK)
54.	5P-0763 E		HOSE (5-CM)
55.	6V-8397	[2]	SEAL-O-RING
56.	5P-8885	[1]	ADAPTER
57.	5C-2890 M	[2]	NUT (M6X1-THD)
58.	7X-0440	[4]	BOLT (5/16-18X1.75-IN)
59.	8T-0389 M	[2]	LOCKNUT (M10X1.5-THD)
60.	7C-4354	[1]	CLIP
61.	5E-8837	[1]	ADAPTER
62.	6V-7743 M	[6]	LOCKNUT (M6X1-THD)
63.	6V-9497	[8]	WASHER-HARD (3.2X6X0.5-MM THK)
64.	102-2991	[1]	SWITCH AS-TOGGLE (RH MOLDBOARD)
65.	102-2991	[1]	SWITCH AS-TOGGLE (LH MOLDBOARD)
			(EACH AS INCLUDES)
	3L-8187	[12]	LOCKWASHER
	6T-3631	[2]	NUT-HEX (15/32-32-THD)
	6T-3632	[1]	LOCKWASHER
	6T-3633	[1]	RING-LOCKING
	6V-8374	[12]	SCREW-MACHINE (6-32X0.25-IN)
66.	7N-8008	[1]	SWITCH AS-TOGGLE (RH ROTOR DOOR)
67.	7N-8008	[1]	SWITCH AS-TOGGLE (LH ROTOR DOOR)
			(EACH AS INCLUDES)
	3L-8187	[6]	LOCKWASHER
	6T-3631	[2]	NUT-HEX (15/32-32-THD)
	6T-3632	[1]	LOCKWASHER
	6T-3633	[1]	RING-LOCKING
	6V-8374	[6]	SCREW-MACHINE (6-32X0.25-IN)
68.	6V-8801	[3]	NUT (3/8-16-THD)
69.	142-5806	[2]	BLOCK
70.	165-2521	[1]	SWITCH AS-PRESSURE (LOW CHARGE)
71.	8T-8902	[1]	ADAPTER-TEE
72.	198-5468	[2]	SWITCH AS-ROCKER (RH REAR LOWER BYPASS)
73.	173-1985	[2]	SWITCH AS-ROCKER (LEGS CONTROL, ALL)
74.	173-1987	[4]	SWITCH AS-ROCKER (LH REAR LOWER BYPASS)
75.	8C-3121	[8]	BOLT (5/16-18X1.5-IN)
76.	116-6565	[2]	BLOCK AS (LIGHT)
77.	180-5617	[2]	BLOCK-CONTACT
78.	116-5275	[2]	SWITCH GP-PUSH BUTTON (OPERATOR)(REMOTE ENGINE STOP)
79.	3T-2357	[1]	SWITCH GP-PUSH BUTTON (HORN)(RIGHT CONTROL STATION)
80.	3T-2357	[1]	SWITCH GP-PUSH BUTTON (HORN)(LEFT CONTROL STATION)
			(EACH AS INCLUDES)
	2H-3922	[1]	LOCKWASHER
	3B-4501	[1]	LOCKWASHER
	5L-7200	[1]	SCREW (8-32X0.375-IN)
	6V-8363	[2]	SCREW (10-32X0.312-IN)
	6V-8370	[1]	NUT-HEX (3/4-32-THD)
	7T-9515	[1]	KNOB-HORN
	8F-1434	[2]	LOCKWASHER
	9X-0199	[1]	BOOT-SWITCH
81.	101-8563	[1]	HARNESS AS-HOOD
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
82.	4M-5281	[2]	BOLT (1/4-20X0.75-IN)
83.	5P-8874	[1]	ADAPTER
84.	6V-2480	[4]	SCREW (4-40X0.5-IN)
85.	6V-8724	[1]	ELBOW
86.	3J-7354	[1]	SEAL-O-RING
87.	175-2308	[1]	SWITCH GP-MAGNETIC (24-VOLT)(START RELAY)
	1H-3338	[2]	LOCKWASHER (EXTERNAL TOOTH)
	5C-2890 M	[2]	NUT (M6X1-THD)
	012-0380	[2]	LOCKWASHER (6.5X12.5X1.6-MM THK)
	186-3735	[2]	PIN-CONNECTOR (16-GA TO 18-GA)
	9X-1813 E		SLEEVE (16-CM)
	102-8802		KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
88.	173-1986	[2]	SWITCH AS-ROCKER (LH FRONT RAISE/LOW)
89.	6D-4636	[1]	CLIP (LOOP)
90.	3E-9865	[2]	LOCKNUT (1/4-20-THD)
91.	1G-9090	[1]	S-HOOK
92.	169-7288	[1]	ADAPTER AS
	8L-2779	[1]	SEAL-O-RING
	8L-2786	[1]	SEAL-O-RING
	B		USE AS REQUIRED
	E		ORDER BY THE CENTIMETER
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#KEBP41320232

143-3633: WIRING GP-REAR

WIRING GP-REAR

143-3633 WIRING GP-REAR
S/N 8GS265-UP
PART OF 141-9440 WIRING GP-MACHINE

i02192753 KEBP4132

For full view, you need register

Parts for your PM-565B COLD PLANER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	101-8562	[1]	HARNESS AS-SENSOR (TRAVEL SPEED)
	7X-6198	[3]	CONNECTOR-END
	3S-2093	[2]	STRAP-CABLE
	5P-1520 E		HOSE (216-CM)
	8T-8731	[2]	PLUG-CONNECTOR (3-PIN)
2.	6D-3479	[3]	CLIP
3.	9X-1439 Y	[4]	LAMP GP-FLOOD (24-VOLT)
4.	8T-9378	[2]	BOLT (3/8-16X4-IN)
5.	8T-4896	[7]	WASHER-HARD (10.2X18.5X2.5-MM THK)
6.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
7.	8T-4121	[9]	WASHER-HARD (11X21X2.5-MM THK)
8.	163-1201 C	[1]	HORN AS (24-VOLT, LOW TONE)
9.	7K-1181 B	[106]	STRAP-CABLE
10.	5P-6264	[1]	GROMMET
11.	4D-1326	[1]	LOCKWASHER (EXTERNAL TOOTH)
12.	3T-1815	[1]	ALARM GP
13.	3S-2093	[21]	STRAP-CABLE
14.	8T-4133 M	[6]	NUT (M10X1.5-THD)
15.	4D-8123	[1]	CLIP
16.	240-5144 C	[1]	HARNESS AS-REAR
	8T-8799	[1]	BOOT (RED)
	8C-3056 E		CABLE (2-GA, RED)(441-CM)
	100-5805	[1]	CAP-RECEPTACLE (3-PIN)
	7N-9738	[1]	HOUSING-RECEPTACLE (14-GA TO 18-GA)
	7N-7780	[1]	PIN-CONNECTOR (14-GA TO 18-GA)
	8T-8729	[20]	PIN-CONNECTOR (16-GA TO 18-GA)
	7X-6222	[1]	PLUG AS-CONNECTOR (24-PIN)
	3E-4367	[1]	RING-RETAINING
	3E-8558 M	[1]	BOLT (M5X0.8X39.37-MM)
	9X-3265	[2]	SEAL-CONNECTOR (24-PIN)
	9X-7147	[1]	PLUG AS-CONNECTOR (40-PIN)
	9X-0141	[2]	PLUG AS-CONNECTOR (40-PIN)
			(EACH PLUG AS INCLUDES)
	3E-4367	[1]	RING-RETAINING
	3E-8557 M	[1]	BOLT (M5X0.8X39.37-MM)
	9X-3490	[2]	SEAL-CONNECTOR (40-PIN)
	155-2260	[5]	KIT-CONNECTING PLUG (3-PIN)
	155-2270	[52]	KIT-CONNECTING PLUG (2-PIN)
	155-2271	[2]	KIT-CONNECTING PLUG (4-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
	3E-7996	[10]	PLUG-CONNECTOR (6-PIN)
	8T-8737	[40]	PLUG-SEAL
	102-8803	[4]	KIT-RECEPTACLE (3-PIN)
			(EACH INCLUDES RECEPTACLE AS & WEDGE)
	9X-4813	[2]	RECEPTACLE AS-CONNECTOR (3-PIN)
	8T-8732	[1]	RECEPTACLE-CONNECTOR (3-PIN)
	7N-7779	[1]	SOCKET-CONNECTOR (14-GA TO 18-GA)
	8T-8730	[228]	SOCKET-CONNECTOR (16-GA TO 18-GA)
	9W-0844	[4]	SOCKET-CONNECTOR (14-GA TO 16-GA)
	189-3158	[20]	SUPPRESSOR-ARC
	030-1712	[2]	TERMINAL-RING (2-GA, 1/4-IN SCREW)
	110-8769	[1]	WIRE AS (16-GA)
	5P-2321	[36]	TERMINAL-FORK (14-GA TO 16-GA, NO. 6 SCREW)
	5P-1475	[10]	TERMINAL-FORK (14-GA TO 16-GA, NO. 8 SCREW)
	2L-8076	[4]	TERMINAL-RING (14-GA TO 16-GA, NO. 10 SCREW)
	2L-8071	[7]	TERMINAL-RING (10-GA TO 12-GA, 1/2-IN SCREW)
	2L-8066	[1]	TERMINAL-RING (10-GA TO 12-GA, NO. 10 SCREW)
	2L-8067	[2]	TERMINAL-RING (10-GA TO 12-GA, 1/4-IN SCREW)
	2L-8081	[2]	TERMINAL-RING (14-GA TO 16-GA, 1/2-IN SCREW)
	065-5071	[64]	TERMINAL-BLADE (14-GA TO 16-GA)
17.	9X-0941	[3]	LOCKNUT (1/2-13-THD)
18.	8T-4223	[3]	WASHER-HARD (13.5X25.5X3-MM THK)
19.	3E-7675	[1]	SWITCH GP-PRESSURE (SYSTEM HYDRAULICS)
20.	3E-7675	[1]	SWITCH GP-PRESSURE (TRACK BRAKE)
			(EACH SWITCH GP INCLUDES)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	8T-8729	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
21.	5P-6944	[1]	ADAPTER
22.	3K-0360	[2]	SEAL-O-RING
23.	3E-8700 Y	[1]	SENSOR GP-TEMPERATURE (HYDRAULIC OIL)
23A.	3E-8700 Y	[1]	SENSOR GP-TEMPERATURE (CLUTCH OIL)
24.	3J-1907	[6]	SEAL-O-RING
25.	4P-8134 C	[1]	CLIP (LADDER)
26.	0L-1407	[1]	GROMMET
27.	1H-3338	[6]	LOCKWASHER (EXTERNAL TOOTH)
28.	6V-3342	[1]	ELBOW-PIPE
29.	134-1419	[1]	BLOCK
30.	3E-6466 Y	[2]	LAMP GP-SIGNAL (24-VOLT)
31.	142-3010	[1]	ENCLOSURE AS-REAR
	5D-9629	[2]	ROD
32.	142-3009	[1]	ENCLOSURE AS-REAR
	5D-9629	[2]	ROD
33.	3E-7842	[1]	RESISTOR AS
34.	116-5270	[2]	LAMP (24-VOLT)(EMERGENCY STOP)
35.	3E-9860	[17]	LOCKNUT (5/16-18-THD)
36.	7J-9108	[2]	SEAL-O-RING
37.	116-5273	[2]	KNOB (RED)
38.	145-4876 Y	[1]	SENSOR GP-PRESSURE ELECTRONIC
39.	153-3962 CY	[1]	SENSOR GP-PRESSURE (CLUTCH OIL)
40.	3K-6060	[2]	LOCKNUT (3/8-16-THD)
41.	8T-4205	[3]	WASHER-HARD (7.2X14.5X2-MM THK)
42.	154-6464	[1]	SWITCH AS-PRESSURE (HYDRAULIC OIL)
43.	7X-0280	[1]	BOLT (5/16-18X5.0-IN)
44.	1G-9089	[1]	CHAIN
45.	4L-6454	[2]	BOLT (3/8-16X1-IN)
46.	5P-8167	[1]	BOLT (3/8-16X0.625-IN)
47.	4M-6425	[4]	BOLT (5/16-18X1-IN)
48.	4P-7581	[3]	CLIP (LADDER)
49.	4S-4455	[2]	CLIP
50.	9N-7446	[8]	LOCKNUT (4-40-THD)
51.	5P-0765 E		HOSE (51-CM)
52.	5P-1079	[4]	SCREW-MACHINE (4-40X0.875-IN)
53.	8T-4224	[30]	WASHER-HARD (8.8X16X2-MM THK)
54.	5P-0763 E		HOSE (5-CM)
55.	6V-8397	[2]	SEAL-O-RING
56.	5P-8885	[1]	ADAPTER
57.	5C-2890 M	[2]	NUT (M6X1-THD)
58.	7X-0440	[4]	BOLT (5/16-18X1.75-IN)
59.	8T-0389 M	[2]	LOCKNUT (M10X1.5-THD)
60.	7C-4354	[1]	CLIP
61.	5E-8837	[1]	ADAPTER
62.	6V-7743 M	[6]	LOCKNUT (M6X1-THD)
63.	6V-9497	[8]	WASHER-HARD (3.2X6X0.5-MM THK)
64.	102-2991	[1]	SWITCH AS-TOGGLE (RH MOLDBOARD)
65.	102-2991	[1]	SWITCH AS-TOGGLE (LH MOLDBOARD)
			(EACH SWITCH AS INCLUDES)
	3L-8187	[12]	LOCKWASHER
	6T-3631	[2]	NUT-HEX (15/32-32-THD)
	6T-3632	[1]	LOCKWASHER
	6T-3633	[1]	RING-LOCKING
	6V-8374	[12]	SCREW-MACHINE (6-32X0.25-IN)
66.	7N-8008	[1]	SWITCH AS-TOGGLE (RH ROTOR DOOR)
67.	7N-8008	[1]	SWITCH AS-TOGGLE (LH ROTOR DOOR)
			(EACH SWITCH AS INCLUDES)
	3L-8187	[6]	LOCKWASHER
	6T-3631	[2]	NUT-HEX (15/32-32-THD)
	6T-3632	[1]	LOCKWASHER
	6T-3633	[1]	RING-LOCKING
	6V-8374	[6]	SCREW-MACHINE (6-32X0.25-IN)
68.	6V-8801	[3]	NUT (3/8-16-THD)
69.	142-5806	[2]	BLOCK
70.	165-2521 C	[1]	SWITCH AS-PRESSURE (LOW CHARGE)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	186-3735	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
71.	8T-8902	[1]	ADAPTER-TEE
72.	198-5468	[2]	SWITCH AS-ROCKER (RH REAR LOWER BYPASS)
73.	173-1985	[2]	SWITCH AS-ROCKER (LEGS CONTROL, ALL)
74.	173-1987	[4]	SWITCH AS-ROCKER (LH REAR LOWER BYPASS)
75.	8C-3121	[8]	BOLT (5/16-18X1.5-IN)
76.	116-6565	[2]	BLOCK AS (LIGHT)
77.	180-5617	[2]	BLOCK-CONTACT
78.	116-5275	[2]	SWITCH GP-PUSH BUTTON (OPERATOR)(REMOTE ENGINE STOP)
79.	3T-2357	[1]	SWITCH GP-PUSH BUTTON (HORN)(RIGHT CONTROL STATION)
80.	3T-2357	[1]	SWITCH GP-PUSH BUTTON (HORN)(LEFT CONTROL STATION)
			(EACH AS INCLUDES)
	2H-3922	[1]	LOCKWASHER
	3B-4501	[1]	LOCKWASHER
	5L-7200	[1]	SCREW (8-32X0.375-IN)
	6V-8363	[2]	SCREW (10-32X0.312-IN)
	6V-8370	[1]	NUT-HEX (3/4-32-THD)
	7T-9515	[1]	KNOB-HORN
	8F-1434	[2]	LOCKWASHER
	9X-0199	[1]	BOOT-SWITCH
81.	101-8563	[1]	HARNESS AS-HOOD
	8T-8729	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	5P-1475	[4]	TERMINAL-FORK (14-GA TO 16-GA, NO. 8 SCREW)
82.	4M-5281	[2]	BOLT (1/4-20X0.75-IN)
83.	5P-8874	[1]	ADAPTER
84.	6V-2480	[4]	SCREW (4-40X0.5-IN)
85.	6V-8724	[1]	ELBOW
86.	3J-7354	[1]	SEAL-O-RING
87.	175-2308	[1]	SWITCH GP-MAGNETIC (24-VOLT)(START RELAY)
	1H-3338	[2]	LOCKWASHER (EXTERNAL TOOTH)
	5C-2890 M	[2]	NUT (M6X1-THD)
	012-0380	[2]	LOCKWASHER (6.5X12.5X1.6-MM THK)
	186-3735	[2]	PIN-CONNECTOR (16-GA TO 18-GA)
	9X-1813 E		SLEEVE (16-CM)
	102-8802		KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
88.	173-1986	[2]	SWITCH AS-ROCKER (LEGS CONTROL, REAR)
89.	6D-4636	[1]	CLIP (LOOP)
90.	3E-9865	[2]	LOCKNUT (1/4-20-THD)
91.	1G-9090	[1]	S-HOOK
92.	169-7288	[1]	ADAPTER AS
	8L-2779	[1]	SEAL-O-RING
	8L-2786	[1]	SEAL-O-RING
	B		USE AS REQUIRED
	C		CHANGE FROM PREVIOUS TYPE
	E		ORDER BY THE CENTIMETER
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#KEBP41320233

133-4060: WIRING GP-ROTOR

WIRING GP-ROTOR

133-4060 WIRING GP-ROTOR
S/N 8GS1-UP
PART OF 140-9456 ROTOR AR

i00502083 KEBP4132

For full view, you need register

Parts for your PM-565B COLD PLANER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	134-5064	[1]	HARNESS AS-CONTROL (ROTOR)
	155-2271	[1]	KIT-CONNECTING PLUG (4-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	7X-6222	[1]	PLUG AS-CONNECTOR (24-PIN)
	3E-4367	[1]	RING-RETAINING
	3E-8558 M	[1]	BOLT (M5X0.8X39.37-MM)
	9X-3265	[2]	SEAL-CONNECTOR (24-PIN)
	8T-8737	[10]	PLUG-SEAL
2.	110-2886	[1]	ENCLOSURE
3.	9X-1439 Y	[2]	LAMP GP-FLOOD (24-VOLT)
4.	3T-2357	[1]	SWITCH GP-PUSH BUTTON (HORN)
	2H-3922	[1]	LOCKWASHER
	3B-4501	[1]	LOCKWASHER
	5L-7200	[1]	SCREW (8-32X0.375-IN)
	6V-8363	[2]	SCREW (10-32X0.312-IN)
	6V-8370	[1]	NUT-HEX (3/4-32-THD)
	7T-9515	[1]	KNOB-HORN
	8F-1434	[2]	LOCKWASHER
	9X-0199	[1]	BOOT-SWITCH
5.	116-5275	[1]	SWITCH GP-PUSH BUTTON (OPERATOR)(REMOTE ENGINE STOP)
6.	180-5617	[1]	BLOCK-CONTACT
7.	116-5273	[1]	KNOB (RED)
8.	7J-9108	[1]	SEAL-O-RING
9.	086-8953	[1]	LAMP (24-VOLT)(REMOTE ENGINE STOP)
10.	4D-1836	[1]	SWITCH-TOGGLE (LIGHT)
11.	9G-0011	[1]	SWITCH AS-TOGGLE (ROTOR ROTATE)
	3L-8187	[3]	LOCKWASHER
	6T-3631	[2]	NUT-HEX (15/32-32-THD)
	6T-3632	[1]	LOCKWASHER
	6T-3633	[1]	RING-LOCKING
	6V-8374	[3]	SCREW-MACHINE (6-32X0.25-IN)
12.	6R-0486 Y	[1]	SENSOR GP-POSITION (SERVICE DOOR)
13.	116-6565	[1]	BLOCK AS (LIGHT)
14.	5E-4158	[4]	MOUNT
15.	7K-1181	[12]	STRAP-CABLE
16.	3S-2093	[5]	STRAP-CABLE
17.	4M-6425	[1]	BOLT (5/16-18X1-IN)
18.	5S-7349	[4]	BOLT (1/4-20X0.5-IN)
19.	3E-9865	[4]	LOCKNUT (1/4-20-THD)
20.	8T-0389 M	[2]	LOCKNUT (M10X1.5-THD)
21.	6V-8189	[1]	NUT (5/16-18-THD)
22.	3E-9860	[1]	LOCKNUT (5/16-18-THD)
23.	1H-3338	[4]	LOCKWASHER (EXTERNAL TOOTH)
24.	8T-4121	[2]	WASHER-HARD (11X21X2.5-MM THK)
25.	8T-4224	[2]	WASHER-HARD (8.8X16X2-MM THK)
26.	9M-8406	[1]	CLIP (LOOP)
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#KEBP41320234

109-0401: WIRING GP-UNIT INJECTOR

WIRING GP-UNIT INJECTOR

109-0401 WIRING GP-UNIT INJECTOR
S/N 99C1019-UP
PART OF 138-8144 ENGINE AR, 215-0565 ENGINE AR-COMPLETE

i00089851 KEBP4132

1090401 WIRING GP-UNIT INJECTOR Parts scheme

For full view, you need register

Parts for your PM-565B COLD PLANER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	7E-6508	[2]	CAP AS
2.	107-6761	[1]	CLIP
3.	2H-3755	[1]	BOLT (5/16-18X0.43-IN)
4.	9M-1974	[1]	WASHER-HARD (8.8X16X2-MM THK)
5.	179-7087	[1]	HARNESS AS-ENGINE (UNIT INJECTOR)
	178-0475	[1]	FILM-INFORMATION (ENGINE WIRING CONNECTION)
	113-4630	[1]	RECEPTACLE AS-CONNECTOR (4-PIN)
6.	033-6034	[1]	SEAL-O-RING
7.	5L-4019	[1]	RING-RETAINING

#KEBP41320235

142-9932: HYDRAULIC AR-PROPEL

HYDRAULIC AR-PROPEL

142-9932 HYDRAULIC AR-PROPEL
S/N 8GS1-UP
PART OF 140-0978 GENERAL AR

i00503972 KEBP4132

For full view, you need register

Parts for your PM-565B COLD PLANER:

CATERPILLAR SIS

Part No	Qty	Parts name
1G-7799 Y	[1]	FILTER & MTG GP-HYDRAULIC
142-9941 Y	[1]	LINES GP-SERVICE BRAKE
142-9940 Y	[1]	LINES GP-HYDROSTATIC
142-9933 Y	[1]	MOTOR & MTG GP-PROPEL
1G-7796 Y	[1]	PUMP & MTG GP-PROPEL
Y		SEPARATE ILLUSTRATION

#KEBP41320236

142-9940: LINES GP-HYDROSTATIC

LINES GP-HYDROSTATIC

142-9940 LINES GP-HYDROSTATIC
S/N 8GS1-UP
PART OF 142-9932 HYDRAULIC AR-PROPEL

i00557975 KEBP4132

1429940 LINES GP-HYDROSTATIC Parts scheme

For full view, you need register

Parts for your PM-565B COLD PLANER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	1G-9767	[1]	TUBE AS
2.	1G-9768	[1]	TUBE AS
3.	1G-9769	[1]	TUBE AS
4.	1G-9770	[1]	TUBE AS
5.	1G-9771	[1]	TUBE AS
6.	101-7784 I	[1]	HOSE AS
7.	102-1666 I	[1]	HOSE AS
8.	102-1667 I	[1]	HOSE AS
9.	127-2257 I	[4]	HOSE AS
10.	101-8758 I	[1]	HOSE AS
11.	101-8759 I	[1]	HOSE AS
12.	101-8760	[2]	HOSE AS
13.	101-8968 I	[8]	HOSE AS
14.	114-5045 I	[4]	HOSE AS
15.	101-9680	[1]	HOSE AS
16.	101-9681	[1]	HOSE AS
17.	100-3478 I	[1]	HOSE AS
18.	101-9697 I	[1]	HOSE AS
19.	4V-0939	[4]	BOLT (5/16-18X1.73-IN)
20.	101-9932 I	[1]	HOSE AS
21.	101-9946 I	[1]	HOSE AS
22.	4V-0611	[6]	CLAMP
23.	7R-7964	[13]	PLATE
24.	6W-0210	[8]	BOLT (5/16-18X1.5-IN)
25.	132-8624 I	[1]	HOSE AS
26.	132-8623 I	[1]	HOSE AS
27.	134-0181 I	[1]	HOSE AS
28.	086-8673	[12]	CLAMP
29.	141-1727 I	[1]	HOSE AS
30.	134-0182 I	[1]	HOSE AS
31.	3V-0046	[10]	PLATE
32.	8C-6561	[5]	BOLT (5/16-18X1.375-IN)
33.	6V-8189	[3]	NUT (5/16-18-THD)
34.	6W-2463	[12]	CLAMP
35.	3J-1907	[5]	SEAL-O-RING
36.	6V-8400	[2]	SEAL-O-RING
37.	2S-4078	[2]	SEAL-O-RING
38.	3K-0360	[7]	SEAL-O-RING
39.	3D-2824	[6]	SEAL-O-RING
40.	2M-9780	[2]	SEAL-O-RING
41.	6V-8398	[25]	SEAL-O-RING
42.	6V-9746	[43]	SEAL-O-RING
43.	4J-5477	[13]	SEAL-O-RING
44.	6V-8397	[6]	SEAL-O-RING
45.	4F-7391	[2]	SEAL-O-RING
46.	1C-4239	[1]	BUSHING-TERMINAL (3/4-16 STR-THD)
47.	6V-8934	[3]	ADAPTER
48.	6V-9002	[1]	ELBOW
49.	6V-9007	[2]	ELBOW
50.	6V-8784	[1]	TEE-FACE SEAL
51.	6V-9850	[1]	ELBOW
52.	6V-9836	[1]	TEE-SWIVEL
53.	101-9682 I	[1]	HOSE AS
54.	8T-3611	[1]	CONNECTOR
55.	6V-9006	[1]	ELBOW
56.	102-1668 I	[1]	HOSE AS
57.	102-2142 I	[1]	HOSE AS
58.	7R-7991 I	[1]	HOSE AS
59.	7X-0871	[2]	TEE
60.	6V-8639	[6]	CONNECTOR
61.	6V-8629	[1]	ELBOW
62.	102-1739 I	[1]	HOSE AS
63.	6V-8640	[1]	CONNECTOR
64.	6V-9853	[3]	ELBOW
65.	1G-8275	[1]	VALVE GP-CHECK
66.	5E-8841	[4]	FLANGE-SPLIT
67.	8C-6877	[8]	BOLT (7/16-14X1.75-IN)
68.	3B-4507	[8]	LOCKWASHER
69.	6V-9004	[1]	ELBOW
70.	6V-8777	[1]	TEE-FACE SEAL
71.	6V-8637	[1]	CONNECTOR
72.	4V-0612	[2]	PLATE
73.	7R-7962	[8]	CLAMP
74.	5P-2675	[1]	BOLT (1/4-20X1.75-IN)
75.	7V-6089	[16]	CLAMP
76.	6V-8556	[7]	NUT (1-3/16-12-THD)
77.	4J-5267	[8]	SEAL-O-RING
78.	8T-4896	[32]	WASHER-HARD (10.2X18.5X2.5-MM THK)
79.	5S-7383	[32]	BOLT (3/8-16X1.75-IN)
80.	7X-8552	[16]	FLANGE
81.	6V-8942	[6]	REDUCER-O-RING
82.	6V-9810	[1]	UNION
83.	2P-1279	[2]	LOCKNUT (9/16-18-THD)
84.	8C-6444	[2]	TEE-BULKHEAD
85.	086-9286	[12]	CLAMP
86.	6R-3320	[4]	COVER
87.	7X-0440	[8]	BOLT (5/16-18X1.75-IN)
88.	5P-4116	[6]	WASHER-HARD (8.8X20.5X2-MM THK)
89.	7X-0282	[1]	BOLT (5/16-18X6.5-IN)
90.	102-3579	[1]	BLOCK
91.	6V-9160	[4]	TEE-FACE SEAL
92.	8V-5719	[1]	BOLT (5/16-18X2-IN)
93.	7X-0264	[4]	BOLT (1/4-20X2.5-IN)
94.	7R-7951	[2]	PLATE
95.	7R-7939	[6]	CLAMP-PIPE
96.	2P-1293	[5]	LOCKNUT (1-3/16-12-THD)
97.	6V-9809	[2]	ELBOW
98.	6V-9807	[1]	UNION
99.	6V-8995	[2]	UNION (STRAIGHT)
100.	6V-8981	[2]	ELBOW
101.	6V-9169	[4]	NUT (13/16-16-THD)
102.	7R-7965	[4]	NUT
103.	086-8656	[24]	NUT
104.	4M-5282	[23]	BOLT (1/4-20X1.5-IN)
105.	7V-5628	[12]	PLATE
106.	7R-7908	[8]	CLAMP
107.	101-7919	[8]	CLAMP-HALF
108.	2R-0504	[6]	NUT (5/16-18-THD)
109.	7X-0280	[4]	BOLT (5/16-18X5.0-IN)
110.	9X-2235	[2]	TEE-SWIVEL
111.	9V-6589	[12]	CLAMP-DOUBLE
112.	101-7938	[4]	CLAMP-HALF
113.	6V-8641	[2]	CONNECTOR
114.	6V-8997	[1]	UNION
115.	7J-9108	[4]	SEAL-O-RING
116.	6V-9839	[3]	TEE-SWIVEL
117.	7V-6234	[1]	PLATE
118.	7R-7960	[2]	BOLT (1/4-20X2-IN)
119.	7R-7955	[1]	PLATE (SLOTTED)
120.	5K-9090	[2]	SEAL-O-RING
121.	7X-0281	[1]	BOLT (5/16-18X5.5-IN)
122.	6V-3965	[1]	FITTING (QUICK DISCONNECT)
123.	6V-0852	[1]	CAP-DUST
124.	4L-9337	[32]	BOLT (3/8-16X1.5-IN)
125.	6V-8941	[1]	REDUCER
126.	6V-8791	[1]	TEE-FACE SEAL
	I		REFER TO HYDRAULIC INFORMATION SYSTEM

#KEBP41320237

142-9933: MOTOR & MTG GP-PROPEL

MOTOR & MTG GP-PROPEL

142-9933 MOTOR & MTG GP-PROPEL
S/N 8GS1-UP
PART OF 142-9932 HYDRAULIC AR-PROPEL

i00503976 KEBP4132

1429933 MOTOR & MTG GP-PROPEL Parts scheme

For full view, you need register

Parts for your PM-565B COLD PLANER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	142-9934 Y	[3]	MOTOR GP-PISTON (PROPEL)
2.	142-9937 Y	[1]	MOTOR GP-PISTON (PROPEL)
3.	100-6620 Y	[1]	SENSOR GP-SPEED (PROPEL)
4.	111-7052	[4]	SEAL-O-RING
5.	7X-2553 M	[8]	BOLT (M16X2X40-MM)
6.	9X-8257	[8]	WASHER (17.5X30X3.5-MM THK)
7.	1V-6341	[1]	SEAL
8.	8T-4122	[1]	WASHER-HARD (17X32X3.5-MM THK)
	M		METRIC PART
	R		REMANUFACTURED PART MAY BE AVAILABLE
	Y		SEPARATE ILLUSTRATION

#KEBP41320238

142-9944: PLANETARY GP-FINAL DRIVE

PLANETARY GP-FINAL DRIVE

142-9944 PLANETARY GP-FINAL DRIVE
S/N 8GS1-UP
PART OF 142-9943 TRACK GP

i00557976 KEBP4132

1429944 PLANETARY GP-FINAL DRIVE Parts scheme

For full view, you need register

Parts for your PM-565B COLD PLANER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	1C-9427	[1]	SEAL GP-DUO-CONE
2.	110-8366	[1]	CONE-BEARING
3.	110-8368	[1]	BEARING-CUP
4.	110-8370	[1]	BEARING-CUP
5.	110-8369	[1]	CONE-BEARING
6.	115-4461	[1]	NUT-BEARING
7.	110-9325	[3]	GEAR-PLANETARY
8.	110-8365	[3]	BEARING-ROLLER CYLINDER
9.	110-8364	[3]	RING-RETAINING
10.	1C-3726	[3]	PIN
11.	110-9326	[3]	SHAFT-PLANETARY
12.	135-8646	[3]	GEAR-PLANETARY
13.	7X-0292	[20]	BOLT (3/8-16X4.5-IN)
14.	7H-3171	[3]	PLUG-PIPE
15.	135-9452	[1]	CARRIER
16.	110-8716	[57]	BEARING AS-NEEDLE
17.	186-6157	[1]	COVER
18.	1P-6071	[1]	RACE-THRUST BEARING
19.	110-8363	[1]	WASHER-THRUST (13.59X31.42X3.94-MM THK)
20.	135-9453	[1]	GEAR-SUN
21.	110-9324	[1]	GEAR-SUN
22.	077-3064	[1]	SEAL-O-RING
23.	110-9316	[1]	GEAR-RING
24.	5B-5821	[2]	DOWEL
25.	110-8715	[1]	SEAL-O-RING
26.	110-8362	[2]	SPACER-THRUST (13.59X31.42X3.94-MM)
27.	5J-3864	[1]	RING-LOCK
28.	3K-0360	[2]	SEAL-O-RING
29.	9S-8005	[2]	PLUG (3/4-16-THD)
30.	115-4357	[1]	BRAKE
31.	077-9990	[1]	RING-RETAINING
32.	110-8633	[1]	COUPLING
33.	1C-3876	[12]	WASHER-THRUST

			AVAILABLE REPAIR KIT(S):
	110-9327	[1]	KIT-BRAKE SPRING
	110-9328	[1]	KIT-SEAL
	110-9329	[1]	KIT-BRAKE LINING

#KEBP41320239

168-6959: PLANETARY GP-FINAL DRIVE

PLANETARY GP-FINAL DRIVE

168-6959 PLANETARY GP-FINAL DRIVE
S/N 8GS1-UP
PART OF 142-9942, 142-9943 TRACK GP

i01271240 KEBP4132

1686959 PLANETARY GP-FINAL DRIVE Parts scheme

For full view, you need register

Parts for your PM-565B COLD PLANER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	077-9990	[1]	RING-RETAINING
2.	110-8633	[1]	COUPLING
3.	1C-9427	[1]	SEAL GP-DUO-CONE
4.	110-8366	[1]	CONE-BEARING
5.	110-8368	[1]	BEARING-CUP
6.	110-8370	[1]	BEARING-CUP
7.	110-8369	[1]	CONE-BEARING
8.	115-4461	[1]	NUT-BEARING
9.	177-4989	[6]	RING-RETAINING
10.	177-4990	[3]	GEAR-PLANETARY
11.	177-4991	[3]	BEARING-ROLLER
12.	110-8364	[3]	RING-RETAINING
13.	1C-3726	[3]	PIN
14.	1C-3876	[12]	WASHER-THRUST
15.	110-8716	[57]	BEARING AS-NEEDLE
16.	135-8646	[3]	GEAR-PLANETARY
17.	7X-0292	[20]	BOLT (3/8-16X4.5-IN)
18.	9X-0881	[3]	PLUG
19.	135-9452	[1]	CARRIER
20.	110-9326	[3]	SHAFT-PLANETARY
21.	1P-6071	[1]	RACE-THRUST BEARING
22.	186-6157	[1]	COVER
23.	110-8363	[1]	WASHER-THRUST (13.59X31.42X3.94-MM THK)
24.	135-9453	[1]	GEAR-SUN
25.	110-9324	[1]	GEAR-SUN
26.	5J-3864	[1]	RING-LOCK
27.	110-8362	[1]	SPACER-THRUST (13.59X31.42X3.94-MM)
28.	077-3064	[1]	SEAL-O-RING
29.	110-9316	[1]	GEAR-RING
30.	5B-5821	[2]	DOWEL
31.	110-8715	[1]	SEAL-O-RING
32.	159-5846	[2]	PLUG-MAGNETIC (FINAL DRIVE PLANETARY)
33.	115-4357	[1]	BRAKE

			AVAILABLE REPAIR KIT(S):
	110-9327	[1]	KIT-BRAKE SPRING (FINAL DRIVE PLANETARY)
	110-9328	[1]	KIT-SEAL (FINAL DRIVE PLANETARY)
	110-9329	[1]	KIT-BRAKE LINING (FINAL DRIVE PLANETARY)

Information:

ELECTRICAL AND STARTING SYSTEM

WIRING GP

Engine News

Correction to The Pocket Guide, SEBD0402 Is Available as a Reference for Routing and Installing Wire Harness Assemblies {1408}
2000/07/01

270-5051 Repair Kit (Electrical Connectors) Available for Repairs to Wiring Harnesses with Ampseal 16 and A4E 2 Connectors {0709, 1408}
2006/03/20

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/13

Special Instruction

Installation of the HEUI Wiring Harness{1251, 1408, 1714}
Installation of the HEUI Wiring Harness{1251, 1408, 1714}

Cross-Reference for Electrical Connectors {7553}
Cross-Reference for Electrical Connectors {7553}

Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}

Installation Procedure for 257-4183 Injector Wiring Harness Kit {1408}
Installation Procedure for 257-4183 Injector Wiring Harness Kit {1408}

Ampseal 16 Connector Peripheral Seal Servicing{7553}
Ampseal 16 Connector Peripheral Seal Servicing{7553}

Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}
Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}

Procedure to Replace Machine Control Software on Cold Planers{7620}
Procedure to Replace Machine Control Software on Cold Planers{7620}

Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}
Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}

Procedure to Replace the Machine Control Software on Certain PM-565 and PM-565B Cold Planers{1408, 7620}
Procedure to Replace the Machine Control Software on Certain PM-565 and PM-565B Cold Planers{1408, 7620}

Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553}
Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553}

Selecting Correct Part Numbers For Sensors and Adapter Harnesses for Certain Machines and Engines{1408, 1439}
Selecting Correct Part Numbers For Sensors and Adapter Harnesses for Certain Machines and Engines{1408, 1439}

Repair Procedure for Damaged Harness Wiring {1408}
Repair Procedure for Damaged Harness Wiring {1408}

Installation Procedure for Product Link PL421 Retrofit{7606}
Installation Procedure for Product Link PL421 Retrofit{7606}

Installation of the White Noise Back Up Alarms {7406}
Installation of the White Noise Back Up Alarms {7406}

DRCP Connector Repair Service Instruction {1408, 7553}
DRCP Connector Repair Service Instruction {1408, 7553}

Service Letter-NACD

PRODUCT IMPROVEMENT PROGRAM FOR REPLACING MACHINE CONTROL SOFTWARE OF ON CERTAIN PM-565 AND PM-565B COLD PLANERS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING MACHINE CONTROL SOFTWARE OF ON CERTAIN PM-565 AND PM-565B COLD PLANERS

PRODUCT IMPROVEMENT PROGRAM FOR REPLACING MACHINE CONTROL SOFTWARE ON CERTAIN PM-565 AND PM-565B MODEL COLD PLANERS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING MACHINE CONTROL SOFTWARE ON CERTAIN PM-565 AND PM-565B MODEL COLD PLANERS

The Second Stage Conveyor May Creep On Certain PM565B Cold Planers
The Second Stage Conveyor May Creep On Certain PM565B Cold Planers

Product Support Program For Installing A New 106-8704 Arc Suppressor (Diode) In Certain PM-565B Cold Planers
Product Support Program For Installing A New 106-8704 Arc Suppressor (Diode) In Certain PM-565B Cold Planers

PRODUCT SUPPORT PROGRAM FOR INSTALLING ETHER STARTING AID ON CERTAIN PM565B COLD PLANERS
PRODUCT SUPPORT PROGRAM FOR INSTALLING ETHER STARTING AID ON CERTAIN PM565B COLD PLANERS

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

The Second Stage Conveyor May Creep On Certain PM565B Cold Planers
The Second Stage Conveyor May Creep On Certain PM565B Cold Planers

PRODUCT SUPPORT PROGRAM FOR INSTALLING ETHER STARTING AID ON CERTAIN PM565B COLD PLANERS
PRODUCT SUPPORT PROGRAM FOR INSTALLING ETHER STARTING AID ON CERTAIN PM565B COLD PLANERS

Service Letter-Americas

The Second Stage Conveyor May Creep On Certain PM565B Cold Planers
The Second Stage Conveyor May Creep On Certain PM565B Cold Planers

PRODUCT SUPPORT PROGRAM FOR INSTALLING ETHER STARTING AID ON CERTAIN PM565B COLD PLANERS
PRODUCT SUPPORT PROGRAM FOR INSTALLING ETHER STARTING AID ON CERTAIN PM565B COLD PLANERS

Technical Information Bulletin

Testing The Function Of The 3E6477 Relay Assembly (24 Volt)
Testing The Function Of The 3E6477 Relay Assembly (24 Volt)

The 108-0358 Electronic Flasher Assembly Is Not A Drop-in Replacement For The 8D-6946 Flasher
The 108-0358 Electronic Flasher Assembly Is Not A Drop-in Replacement For The 8D-6946 Flasher

Specifications

Unit Injector Wiring
3408E and 3412E Engines for Caterpillar Built Machines

Tool Operating Manual

Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}
Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}

Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}

Service Letter-China

Service Letter-Asia

Systems Operation

Cat Data Link
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Relays
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Electronic Control Module (ECM)
PM-565 and PM-565B Cold Planers Machine Electronic Control System

General Information
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Computerized Monitoring System
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Switches
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Propel Control
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Load Control
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Steering Control
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Rotor Control
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Water Spray Control
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Diagnostic Operation
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Reuse And Salvage Guidelines

Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}

Service Letter-APD

Testing and Adjusting

Electric Starting System - Test
3408E and 3412E Engines for Caterpillar Built Machines

Electrical Connector - Inspect
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Electronic Control Module (ECM) - Replace
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Propel Lever - Calibrate
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Rotor Mode Switch - Calibrate
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Calibration
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Wiring Harness (Open Circuit) - Test
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Wiring Harness (Short Circuit) - Test
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Steering Mode Switch - Calibrate
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Electrical Connector - Inspect
Product Link - PL522/523

Wiring Harness (Open Circuit) - Test
Product Link - PL522/523

Wiring Harness (Short Circuit) - Test
Product Link - PL522/523

Electrical Connector - Inspect
Product Link 121S/300

Wiring Harness (Open Circuit) - Test
Product Link 121S/300

Wiring Harness (Short Circuit) - Test
Product Link 121S/300

Troubleshooting

Connector Locations
PM-565 and PM-565B Cold Planers Machine Electronic Control System

General Information
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Determining Diagnostic Codes
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 070 FMI F02
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 168 FMI F03
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 168 FMI F04
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 322 FMI F03
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 322 FMI F05
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 322 FMI F06
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 623 FMI F02
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 637 FMI F03
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 637 FMI F05
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 637 FMI F06
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Power Supply Circuit of Electronic Control Module
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 755 FMI F03
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 755 FMI F06
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 755 FMI F05
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 748 FMI F02
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 749 FMI F02
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 750 FMI F02
PM-565 and PM-565B Cold Planers Machine Electronic Control System

CID 751 FMI F02
PM-565 and PM-565B Cold Planers Machine Electronic Control System

Diagnostic Code List
PM-565 and PM-565B Cold Planers Machine Electronic Control System

MID 122 - CID 0269 - FMI 03
Product Link 121S/300

MID 122 - CID 0269 - FMI 04
Product Link 121S/300

Service Magazine

Methods Of Obtaining Engine Flash Files {1902}
1997/01/20

Improved Coolant Flow Switches Available {7425}
1997/06/09

Improved Switches Now Used To Prevent Open Contacts{1423}
1997/08/11

Improved Switches Now Used To Prevent Open Contacts {1423}
1997/11/24

Caterpillar Service Technology Group (CSTG) Software Help Desk Changes {1920}
1999/08/17

New Electronic Control Module For 3408E And 3412E Engines {1901}
1999/08/30

Special Instruction, REHS0440 is Available for an Index of Electrical System Schematics {7566}
2000/04/10

Correction to The Pocket Guide, SEBD0402, Is Available as a Reference for Routing and Installing Wire Harness Assemblies {1408}
2000/06/26

New Injector Wiring Harnesses Are Color Coded {1251, 1408}
2000/08/21

A New Wiring Harness Is Available {1408}
2000/09/11

Dielectric Grease Should Not Be Used in Electrical Connectors {1408, 7553}
2012/05/04

Service Magazine Article Retraction. {0000}
2003/02/03

The Main Power Relay Has Improved Sealing {1423}
2009/05/18

Service of the Machined Terminals and the Stamped and Formed Terminals {7553}
2006/11/13

A New Procedure is Available to Update Software for the Control of the Rotor on Cold Planers {7620}
2008/03/24

Updated Instruction For The Bypass Harness {0785, 1408}
2008/03/17

A New Procedure is Available to Update the Machine Control Software for the Control of the Rotor on Certain Cold Planers {1408, 7620}
2010/01/28

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2012/03/05

Striped Wire Is Replaced With Improved Ink Jet Identification for Legacy (Parts Service) Wire harnesses {1408}
2012/06/08

Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}
2012/05/08

Information On Battery Cables and Wire Assemblies for Assembling at Dealer Site {4459}
2012/09/21

Parts are Now Available to Make Jump Start Receptacle on Cat<SUP>®</SUP> Product {1463}
2014/03/04

Comprehensive List of Electrical Repair and Troubleshooting Information Is Now Available for All CAT Machines {0374, 0709, 1400, 1408, 7490, 7553, 7610}
Comprehensive List of Electrical Repair and Troubleshooting Information Is Now Available for All CAT Machines {0374, 0709, 1400, 1408, 7490, 7553, 7610}

Caterpillar Parts SIS Catalog PM-565B :

141-2462 WIRING GP-FRONT

121-4082 WIRING GP-ENGINE ELECTRONIC

201-6947 WIRING GP-CONVEYOR

134-6229 WIRING GP-CONVEYOR

141-0715 WIRING GP-CONSOLE

143-3633 WIRING GP-REAR

133-4060 WIRING GP-ROTOR

109-0401 WIRING GP-UNIT INJECTOR

142-9932 HYDRAULIC AR-PROPEL

142-9940 LINES GP-HYDROSTATIC

142-9933 MOTOR & MTG GP-PROPEL

142-9944 PLANETARY GP-FINAL DRIVE

Truck sale:

USD $79,900

2003 CAT PM-565B

Stoneman Motors LLC

USD $84,900

CAT PM-565B

Stoneman Motors LLC

USD $97,000

2004 CAT PM-565B

USA Equipco
Hidalgo, Texas

USD $87,000

2001 CAT PM-565B

USA Equipco
Hidalgo, Texas

$99,500 USD

CATERPILLAR PM-565B 1999
- COLD PLANERS
RANSOME CAT
Pennsylvania United States