0773902 KIT-HYDRAULIC FLANGE Caterpillar parts
CB-614
Rating:
Alternative (cross code) number:
CA0773902
077-3902
0773902
CA0773902
077-3902
0773902
Weight: 0.01 pounds 0 kg.
VIBRATORY COMPACTOR,
Compatible equipment models: 0773902:
Number on catalog scheme:
25
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1 Start By:
Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00991548
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Use Tooling (A) to compress valve spring (4). Remove retainer lock (6).
Remove Tooling (A). Remove spring retainer (5), valve spring (4), and washer (3).
Remove valve seal (1) and valve (2).
Repeat Steps 1 through 3 in order to remove the remaining inlet valves and exhaust valves. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00991548
The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.
Lubricate valve (2) with clean engine oil. Install valve (2) in the cylinder head assembly. Install new valve seal (1) onto the valve guide.
Place the following items on the valve stem: washer (3), valve spring (4) and spring retainer (5). Note: A small amount of grease can be used to hold the retainer locks in position during installation.
Use Tooling (A) to compress valve spring (4). Install retainer lock (6).
Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves. End By:
Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1 Start By:
Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00991548
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Use Tooling (A) to compress valve spring (4). Remove retainer lock (6).
Remove Tooling (A). Remove spring retainer (5), valve spring (4), and washer (3).
Remove valve seal (1) and valve (2).
Repeat Steps 1 through 3 in order to remove the remaining inlet valves and exhaust valves. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00991548
The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.
Lubricate valve (2) with clean engine oil. Install valve (2) in the cylinder head assembly. Install new valve seal (1) onto the valve guide.
Place the following items on the valve stem: washer (3), valve spring (4) and spring retainer (5). Note: A small amount of grease can be used to hold the retainer locks in position during installation.
Use Tooling (A) to compress valve spring (4). Install retainer lock (6).
Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves. End By:
Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
1G5036
KIT-BUMPER
CB-614
CB-614
120G, 12G, 130G, 140G, 14G, 160G, 1673C, 16G, 215, 215B, 235, 245, 3116, 3176B, 3176C, 3196, 3208, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3412, 3412C, 3...
120G, 12G, 130G, 140G, 14G, 160G, 1673C, 16G, 215, 215B, 235, 245, 3116, 3176B, 3176C, 3196, 3208, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3412, 3412C, 3...
7X1029
KIT-HARDWARE
3114, 3116, 3126, 3208, 3304, 3304B, 3306B, 3408, CB-614, CS-551, G3306
3114, 3116, 3126, 3208, 3304, 3304B, 3306B, 3408, CB-614, CS-551, G3306
225, 227, 3208, 613B, CB-614, CS-551
621E, 621F, 631E, AP-1000, AP-1000B, AP-800, AP-900B, CB-224C, CB-614, CP-433B, CS-551, RR-250, SM-350, SS-250
0774080
KIT-CYLINDER BLOCK
CB-614, CS-551, RR-250, SS-250
CB-614, CS-551, RR-250, SS-250
1206514
KIT, CLAMP
CB-514, CB-614
CB-514, CB-614
1206772
KIT, ROPS
CB-614
CB-614
0329868
KIT-FILTER
RR-250
RR-250
7R6301
KIT-BYPASS
RR-250
RR-250
0778320
KIT-SEAL
RR-250
RR-250
0779852
KIT-ROTATING
RR-250
RR-250
0829319
KIT-SEAL
CB-521
CB-521
0814556
KIT-SEAL
CB-521
CB-521
0870326
KIT-END CAP
AP-800
AP-800
5E8004
KIT-SEAL
AP-800
AP-800
0905193
KIT-CARTRIDGE
CP-563
CP-563
6A7899
KIT-SEAL
CP-563
CP-563
1G5011
KIT-SPRING PACK
CB-434
CB-434
5E0100
KIT-CLAMP
CB-614
CB-614