1057379 KIT-SEAL Caterpillar parts
315, 317
Rating:
Alternative (cross code) number:
CA1057379
105-7379
1057379
CA1057379
105-7379
1057379
Weight: 0.50 pounds 0 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Replacement for fits 1057379 Stick Seal Kit 85mm Rod Fits Caterpillar Fits CAT Excavator 315 317 315L
Leechin
Leechin
105-7359 105-7379 Boom Arm Bucket Seal Kits E317 315 317N 315L Compatible with CAT (Bucket)
Generic 105-7359 105-7379 Boom Arm Bucket Seal Kits E317 315 317N 315L Compatible with CAT
Generic 105-7359 105-7379 Boom Arm Bucket Seal Kits E317 315 317N 315L Compatible with CAT
Number on catalog scheme:
For full view, you need register
Information:
Introduction
Use this procedure to find the top center position for the number 1 piston.Required Tools
Table 1
Required Tools
Part Number Part Name Qty
9S-9082 Engine Turning Tool 1 Check Preparation
Turn off the engine.
Illustration 1 g01193047
Timing bolt location (typical example)
(1) Cover
(2) Timing bolt
(3) Plug
Remove cover (1) and plug (3) from the right front side of the flywheel housing. Refer to Illustration 1.
Illustration 2 g01193048
Timing bolt installation (typical example)
(2) Timing bolt
(4) 9S-9082 Engine Turning Tool
Put timing bolt (2) through the timing hole in the flywheel housing. Use engine turning tool (4) and a 1/2 inch drive ratchet wrench to turn the flywheel in the direction of normal engine rotation. Turn the flywheel until the timing bolt engages with the hole in the flywheel. Refer to Illustration 2.Note: If the flywheel is turned beyond the point of engagement, the flywheel must be turned in the direction that is opposite of normal engine rotation. Turn the flywheel by approximately 30 degrees. Then turn the flywheel in the direction of normal engine rotation until the timing bolt engages with the threaded hole. This procedure will remove the play from the gears when the No. 1 piston is on the top center.
Remove the valve cover for the No. 1 cylinder head.
The inlet and exhaust valves for the No. 1 cylinder are fully closed if the No. 1 piston is on the compression stroke. The rocker arms can be moved by hand when the No. 1 piston is on the compression stroke. If the rocker arms cannot be moved and the valves are slightly open, the No. 1 piston is on the exhaust stroke. Find the cylinders that can be checked or adjusted for the stroke position of the crankshaft once the timing bolt has been installed. Refer to Testing and Adjusting, "Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting".Note: When the actual stroke position is identified and the other stroke position is needed, remove the timing bolt from the flywheel. Turn the flywheel by 360 degrees in the direction of normal engine rotation.
Use this procedure to find the top center position for the number 1 piston.Required Tools
Table 1
Required Tools
Part Number Part Name Qty
9S-9082 Engine Turning Tool 1 Check Preparation
Turn off the engine.
Illustration 1 g01193047
Timing bolt location (typical example)
(1) Cover
(2) Timing bolt
(3) Plug
Remove cover (1) and plug (3) from the right front side of the flywheel housing. Refer to Illustration 1.
Illustration 2 g01193048
Timing bolt installation (typical example)
(2) Timing bolt
(4) 9S-9082 Engine Turning Tool
Put timing bolt (2) through the timing hole in the flywheel housing. Use engine turning tool (4) and a 1/2 inch drive ratchet wrench to turn the flywheel in the direction of normal engine rotation. Turn the flywheel until the timing bolt engages with the hole in the flywheel. Refer to Illustration 2.Note: If the flywheel is turned beyond the point of engagement, the flywheel must be turned in the direction that is opposite of normal engine rotation. Turn the flywheel by approximately 30 degrees. Then turn the flywheel in the direction of normal engine rotation until the timing bolt engages with the threaded hole. This procedure will remove the play from the gears when the No. 1 piston is on the top center.
Remove the valve cover for the No. 1 cylinder head.
The inlet and exhaust valves for the No. 1 cylinder are fully closed if the No. 1 piston is on the compression stroke. The rocker arms can be moved by hand when the No. 1 piston is on the compression stroke. If the rocker arms cannot be moved and the valves are slightly open, the No. 1 piston is on the exhaust stroke. Find the cylinders that can be checked or adjusted for the stroke position of the crankshaft once the timing bolt has been installed. Refer to Testing and Adjusting, "Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting".Note: When the actual stroke position is identified and the other stroke position is needed, remove the timing bolt from the flywheel. Turn the flywheel by 360 degrees in the direction of normal engine rotation.
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
307, 315, 317, 416B, 416C, 428B, 428C, 438C
120G, 12G, 130G, 140G, 14G, 160G, 16G, 303, 304, 305, 305.5, 306, 307, 307B, 307C, 308C, 311, 311B, 311C, 312, 3126, 3126B, 312B L, 312C L, 314C, 315, 315B L, 315C, 317, 3176B, 3176C, 317B LN, 318B, 3...
206, 212, 3054, 3054B, 3054C, 307, 312, 312B L, 312C, 315, 315B L, 317, 414E, 416B, 416C, 416D, 416E, 420D, 420E, 422E, 424D, 426B, 426C, 428, 428B, 428C, 428E, 430D, 430E, 432E, 434E, 436C, 438C, 442...
206, 212, 3054, 3054B, 307, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 426B, 426C, 428, 428B, 428C, 430D, 436C, 438C, 554, 908, 914G, AP-800C, BG-225C, CB-424, CB-434B, CB-434C, CB-5...
206, 212, 3054, 3054B, 307, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 426B, 426C, 428, 428B, 428C, 430D, 436C, 438C, 554, 908, 914G, AP-800C, BG-225C, CB-424, CB-434B, CB-434C, CB-5...
206, 212, 3054, 3054B, 307, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 426B, 426C, 428, 428B, 428C, 430D, 436C, 438C, 554, 908, 914G, AP-800C, BG-225C, CB-424, CB-434B, CB-434C, CB-5...
3054, 307, 312, 315, 317, 416C, 426C, 428C, 436C, 914G, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, IT14G, PS-150B, PS-200B, PS-300B, TH10...
3054, 315, 317, 416B, 416C, 428C, 914G, AP-800C, BG-225B, CB-434B, CB-534B, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, IT14G, PS-150B, PS-200B, PS-300B, TH62, TH63, TH82, TH83
120G, 12G, 130G, 135H NA, 140G, 143H, 14G, 14H NA, 160H ES, 160H NA, 163H NA, 16G, 215, 215B, 225, 235, 235B, 245, 307, 312, 312B L, 315, 315B L, 317, 320B, 322 FM L, 322B L, 322B LN, 325B L, 330, 330...
315, 317
315, 317
315, 315B, 315C, 317B LN, 318B
315, 317
315, 317
1218773
KIT-BOTTOM GUARD
315, 317
315, 317
1379433
KIT-ACTUATOR
315, 317
315, 317
312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320B, 322B LN, 325B L, 330B L, 345B II, 345B L, 365B, 365B II, 385B, 5090B
1416603
KIT-CATCH
307, 307B, 312, 312B L, 312C, 315, 315B L, 315C, 317, 317B LN, 318B, 318C, 319C, 320B, 320C, 322B LN, 322C, 323D L, 323D LN, 324D, 324D L, 324D LN, 325B L, 325C, 325D, 325D L, 330B L, 330C, 330C L, 33...
307, 307B, 312, 312B L, 312C, 315, 315B L, 315C, 317, 317B LN, 318B, 318C, 319C, 320B, 320C, 322B LN, 322C, 323D L, 323D LN, 324D, 324D L, 324D LN, 325B L, 325C, 325D, 325D L, 330B L, 330C, 330C L, 33...
M318
315, 317
1345466
KIT-FRONT & BOOM
315, 317
315, 317
1345473
KIT-HARDWARE
315, 317
315, 317
1345898
KIT-FRONT
315, 317
315, 317
1108247
KIT-BOOM LINES
315, 317
315, 317