KIT-SEAL 1306876 - Caterpillar

Illustration 3 g06274219
View of plate
(R) Bolt
(S) Washer
(T) Gasket
(X) Plate
Remove three bolts (R), three washers (S), plate (X), and gasket (T) from the right-hand side of the cab. Retain gasket (T), three washers (S), and three bolts (R) for later installation. Discard plate (X).Installation Procedure
Illustration 4 g06266115
View of antenna cable
(3) 553-9639 Antenna Cable
Route antenna cable (3) through the hole on the right side of the console.Mount the magnetic antenna on the backside of the console for the time being.Note: If the pipelayer has an open rollover protection system, then the load moment indicator display antenna is mounted on the backside of the dash assembly.Note: If the pipelayer has a cab, then the load moment indicator display antenna is mounted on the roof of the cab.
Illustration 5 g06266290
View of antenna cable and harnesses
(3) 553-9639 Antenna Cable
Route antenna cable (3) through the right side hole of the front plate. Make sure antenna cable (3) has an extra 40.64 cm (16 inch) to 45.72 cm (18 inch) inches from the right side hole of the front plate.Note: Extra antenna cable (3) will need to be bundled up and tie wrapped to the existing harness.
Illustration 6 g06266143
View of harnesses and dash cover
(3) Antenna Cable
(F) Key Switch Harness
(G) Load Moment Indicator Harness
(H) Tie Strap
(K) Dash Cover
(L) Bolt
(M) Main Display Harness
Route load moment indicator harness (G), main display harness (M), key switch harness (F) , and antenna cable (3) through the hole of dash cover (K).Install dash cover (K) to the front plate with six bolts (L). Tighten six bolts (L).Connect load moment indicator harness (G), main display harness (M), and key switch harness (F).Secure load moment indicator harness (G), main display harness (M), key switch harness (F) , and antenna cable (3) neatly with the new tie strap (H).
Illustration 7 g06266382
View of plate assembly
(A) Screw
(B) Plate Assembly
Install plate assembly (B) to the dash cover with two screws (A). Tighten two screws (A).
Illustration 8 g06266388
View of load moment indicator display
(1) 553-9637 Bracket
(2) 553-9638 Display
(3) 553-9639 Antenna Cable
(N) Harness
Illustration 9 g06266392
View of load moment indicator display
(1) 553-9637 Bracket
(2) 553-9638 Display
(A) Screw
Connect antenna cable (3) and harness (N) to load moment indicator display (2).Install load movement indicator display (2) and bracket assembly (1) to the dash cover with four screws A. Tighten four screws (A).Note: Installation of load moment indicator chassis sensor.
Illustration 10 g06266415
View of load moment indicator chassis sensor
(4) 519-4077 Machine Angle Sensor
(R) Bolt
(S) Washer
(T) Gasket
Install chassis sensor (4) to the right-hand side of the cab with gasket (T), three washers (S), and three bolts (R). Tighten three bolts (R).Note: Installation of load moment indicator boom angle sensor.
Illustration 11 g06266437
View of boom angle sensor
(5) 555-1555 Boom Angle Sensor
(6) 555-1556 Boom Angle Sensor Installation hardware
Install sensor (5) and the bracket assembly to the angle boom with two washers and two bolts (6). Tighten two bolts (6).Note: Installation of the load pin, zinc clevis pin, and cotter pin.
Illustration 12 g06266449
View of load pin assembly
(7) 519-4072 Load Pin and Retention Hardware
(Y) Puller Assembly
(Z) Angle Boom
Use a suitable support to secure puller assembly (Y) on the ground. Install load pin