1801261 KIT-DISC SPRING Caterpillar parts
M325B, RM-500
Rating:
Alternative (cross code) number:
CA1801261
180-1261
1801261
CA1801261
180-1261
1801261
Weight: 3 pounds 1 kg.
RECLAIMER MIXER, WHEELED EXCAVATOR,
Number on catalog scheme:
3
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 438-3244 Oil Seal Installer 1
8T-0375 Bolt 1
5P-8247 Hard Washer 1
B 438-3245 Oil Seal Locator 1
9U-6172 Bolt 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces or damaged seal surfaces. Wear sleeves are not original equipment. The wear sleeve is supplied with a crankshaft rear seal that has a larger internal diameter than a standard crankshaft rear seal. A standard crankshaft rear seal cannot be used if a wear sleeve is installed.
Ensure that the crankshaft is thoroughly clean and dry. Remove any areas of raised damage.
Lubricate the inner surface of the crankshaft wear sleeve with clean engine oil.
Illustration 1 g03657723
Sectional view of the crankshaft, the wear sleeve, and the installation tool
Use Tooling (A) and Tooling (B) to install the crankshaft wear sleeve, as follows:
Align Tooling (B) with the dowels in crankshaft (2) and install Tooling (B) to the crankshaft. Ensure the correct orientation. Note: Verify that Tooling (A) will slide freely over Tooling (B).
Carefully slide crankshaft wear sleeve (1) over Tooling (B) until the crankshaft wear sleeve contacts the rear of crankshaft (2).
Assemble Tooling (A) to Tooling (B) and install the bolt and the washer. Ensure that the face of Tooling (A) with the deep counterbore is toward crankshaft wear sleeve (1).
Tighten the bolt until Tooling (A) bottoms out on Tooling (B) in order to pull crankshaft wear sleeve (1) onto crankshaft (2).
Remove Tooling (A) and Tooling (B). End By:
Install the new crankshaft rear seal that was supplied with the crankshaft wear sleeve.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 438-3244 Oil Seal Installer 1
8T-0375 Bolt 1
5P-8247 Hard Washer 1
B 438-3245 Oil Seal Locator 1
9U-6172 Bolt 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces or damaged seal surfaces. Wear sleeves are not original equipment. The wear sleeve is supplied with a crankshaft rear seal that has a larger internal diameter than a standard crankshaft rear seal. A standard crankshaft rear seal cannot be used if a wear sleeve is installed.
Ensure that the crankshaft is thoroughly clean and dry. Remove any areas of raised damage.
Lubricate the inner surface of the crankshaft wear sleeve with clean engine oil.
Illustration 1 g03657723
Sectional view of the crankshaft, the wear sleeve, and the installation tool
Use Tooling (A) and Tooling (B) to install the crankshaft wear sleeve, as follows:
Align Tooling (B) with the dowels in crankshaft (2) and install Tooling (B) to the crankshaft. Ensure the correct orientation. Note: Verify that Tooling (A) will slide freely over Tooling (B).
Carefully slide crankshaft wear sleeve (1) over Tooling (B) until the crankshaft wear sleeve contacts the rear of crankshaft (2).
Assemble Tooling (A) to Tooling (B) and install the bolt and the washer. Ensure that the face of Tooling (A) with the deep counterbore is toward crankshaft wear sleeve (1).
Tighten the bolt until Tooling (A) bottoms out on Tooling (B) in order to pull crankshaft wear sleeve (1) onto crankshaft (2).
Remove Tooling (A) and Tooling (B). End By:
Install the new crankshaft rear seal that was supplied with the crankshaft wear sleeve.
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
16G, 16H NA, 24H, 24M, 3126, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 3516, 375, 375 L, 385B, 5080, 5090B, 5110B, 578, 583R, 583T, 587R, 587T, 589, 621B, ...
120G, 12G, 130G, 140G, 14G, 160G, 16G, 303, 304, 305, 305.5, 306, 307, 307B, 307C, 308C, 311, 311B, 311C, 312, 3126, 3126B, 312B L, 312C L, 314C, 315, 315B L, 315C, 317, 3176B, 3176C, 317B LN, 318B, 3...
120K, 120K 2, 12K, 140K, 140K 2, 160K, 303.5E, 303E CR, 304E, 305.5E, 305E, 307E, 308E, 308E2 CR, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D...
120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 235C, 30/30, 3116, 3126,...
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14H, 14H NA, 14M,...
120G, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673C, 16G, 16H, 16H NA, 16M, 215B,...
120G, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673C, 16G, 16H, 16H NA, 16M, 215B,...
120G, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673C, 16G, 16H, 16H NA, 16M, 215B,...
1090, 1190, 1190T, 1290T, 1390, 216, 228, 236, 236B, 242B, 247, 247B, 248, 24H, 267, 267B, 268B, 287, 320D, 320D FM, 322B L, 324D FM, 324D FM LL, 325B L, 325C FM, 325D FM, 325D FM LL, 325D MH, 330, 33...
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 135H, 135H NA, 140G, 140K, 140K 2, 160K, 214B, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 32...
120H NA, 3116, 3126, 3126B, 3126E, 320B, 325B L, 525B, 613C II, 938G, 950G, 962G, AP-1000B, AP-1055B, BG-2455C, BG-245C, IT38G, IT62G, M325B
2384C, 2484C, 311C, 311D LRR, 311F LRR, 312B L, 312C, 312C L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315B L, 315C, 317B LN, 318B, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM R...
2587534
KIT-SEAL
RM-500
RM-500
M325B, RM-500
2561156
KIT-VALVE
RM-300, RM-500
RM-300, RM-500
2610036
KIT-SEAL
AP-1055D, AP-655D, BG655D, RM-300, RM-500
AP-1055D, AP-655D, BG655D, RM-300, RM-500
2608762
KIT-SENSOR
RM-300, RM-500
RM-300, RM-500
2657396
KIT-BRAKE
RM-500
RM-500
2559177
KIT-SEAL
RM-300, RM-500
RM-300, RM-500
2556256
KIT-SEAL
AP-1055D, AP-655D, BG655D, RM-500
AP-1055D, AP-655D, BG655D, RM-500
3869394
KIT-LINING
RM-500
RM-500
3732006
KIT-SEAL
RM-500
RM-500
1801260
KIT-SPRING
M325B, RM-500
M325B, RM-500
3688066
KIT-DISC SPRING
RM-500
RM-500