1850109 KIT-PISTON RING Caterpillar parts
3054B, 416D, 424D, CS-423E, TH210, TH215
Rating:
Alternative (cross code) number:
CA1850109
185-0109
1850109
CA1850109
185-0109
1850109
Weight: 0.13 pounds 0 kg.
BACKHOE LOADER, VIBRATORY COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
KMP BRAND 185-0109 Piston Ring Set - STD Suitable for Caterpillar 1850109
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
KMP BRAND 185-0109 Piston Ring Set - STD Suitable for Caterpillar 1850109
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
Compatible equipment models: 1850109:
Information:
3304B ( 10E, 4XB, 13E, 83Z, 3TC ),
3306B ( 64Z, 7JB, 84Z, 63Z, 5KD, 85Z, 5JC ),
3406B ( 6TB, 2WB, 7FB)Introduction
A field installation kit, group number 7C7466, is now available to install a 8C4770 Solenoid Group. The new 8C4770 Solenoid Group has internal electrical improvements and uses studs and nuts with hardened washers for mounting.The studs also serve as an alignment guide to ensure that the solenoid plunger fits into the governor properly (without bending).The kit contains all the required parts (except expendables) to make the repair.Reference: Parts Book and Service ManualInstallation of 7C7466 Solenoid Repair Kit
1. Refer to the Service Manual for disassembly procedure.2. Remove and discard the former 6T8021 Solenoid, gasket and mounting bolts.Installation of 7C5544 Studs
1. The 7C5544 Studs are precoated, at the factory, with a thread locking compound (on one end of each stud). 2. Install the precoated end of 7C5544 Studs (5), to the dimension shown above, into governor housing (1).
DO NOT install the 7C5544 Studs using a power tool. The governor housing and mounting hole threads could be damaged.
3. Install 2W5447 Gasket (2), 8C4770 Solenoid (3) and 5P0537 Washers (4).4. Coat the exposed end of each 7C5544 Stud (5) with a small amount of 9S3263 Compound (not included in kit) or equivalent thread locking material.5. Install 1B4330 Nuts (6) and tighten to a torque of 12 4N m (9 3 lb ft).Voltage and Current Requirements
Voltage and current requirements for the new 8C4770 Solenoid are the same as for the former 6T8021 Solenoid and should be reviewed and the wiring system modified, if necessary, to ensure dependable operation.The 8C4770 Solenoid is a 12V dual coil solenoid. This type of solenoid has one coil that pulls in the solenoid plunger and another coil that holds the plunger in the ENGINE RUN position.The pull-in coil draws 57.1 amps at 25° C (77° F) and 76.8 amps at -40° C (-40° F).The hold-in coil draws only 1.2 amps at 25° C (77° F) and 1.8 amps at -40° F).Ideally, the pull-in coil will be energized (activated) for only 0.020 seconds. However it may be energized for as long as one second because of oil, dirt and other contamination restricting the plunger movement. A slow-blow type fuse or circuit breaker must be chosen that will provide adequate circuit protection and withstand the short duration, high current situation, caused by restricted plunger movement.Solenoid Grounding Requirements
The 8C4770 Solenoid should be grounded using 14 Ga wire, to a location which provides an uninterrupted ground path.The recommended locations for grounding are on the engine cylinder block or on the vehicle frame rail, depending on which of these structures the batteries are grounded to. DO NOT use solenoid mounting studs (5), washers (4), or nuts (6) as a connection point for the ground wire.
3306B ( 64Z, 7JB, 84Z, 63Z, 5KD, 85Z, 5JC ),
3406B ( 6TB, 2WB, 7FB)Introduction
A field installation kit, group number 7C7466, is now available to install a 8C4770 Solenoid Group. The new 8C4770 Solenoid Group has internal electrical improvements and uses studs and nuts with hardened washers for mounting.The studs also serve as an alignment guide to ensure that the solenoid plunger fits into the governor properly (without bending).The kit contains all the required parts (except expendables) to make the repair.Reference: Parts Book and Service ManualInstallation of 7C7466 Solenoid Repair Kit
1. Refer to the Service Manual for disassembly procedure.2. Remove and discard the former 6T8021 Solenoid, gasket and mounting bolts.Installation of 7C5544 Studs
1. The 7C5544 Studs are precoated, at the factory, with a thread locking compound (on one end of each stud). 2. Install the precoated end of 7C5544 Studs (5), to the dimension shown above, into governor housing (1).
DO NOT install the 7C5544 Studs using a power tool. The governor housing and mounting hole threads could be damaged.
3. Install 2W5447 Gasket (2), 8C4770 Solenoid (3) and 5P0537 Washers (4).4. Coat the exposed end of each 7C5544 Stud (5) with a small amount of 9S3263 Compound (not included in kit) or equivalent thread locking material.5. Install 1B4330 Nuts (6) and tighten to a torque of 12 4N m (9 3 lb ft).Voltage and Current Requirements
Voltage and current requirements for the new 8C4770 Solenoid are the same as for the former 6T8021 Solenoid and should be reviewed and the wiring system modified, if necessary, to ensure dependable operation.The 8C4770 Solenoid is a 12V dual coil solenoid. This type of solenoid has one coil that pulls in the solenoid plunger and another coil that holds the plunger in the ENGINE RUN position.The pull-in coil draws 57.1 amps at 25° C (77° F) and 76.8 amps at -40° C (-40° F).The hold-in coil draws only 1.2 amps at 25° C (77° F) and 1.8 amps at -40° F).Ideally, the pull-in coil will be energized (activated) for only 0.020 seconds. However it may be energized for as long as one second because of oil, dirt and other contamination restricting the plunger movement. A slow-blow type fuse or circuit breaker must be chosen that will provide adequate circuit protection and withstand the short duration, high current situation, caused by restricted plunger movement.Solenoid Grounding Requirements
The 8C4770 Solenoid should be grounded using 14 Ga wire, to a location which provides an uninterrupted ground path.The recommended locations for grounding are on the engine cylinder block or on the vehicle frame rail, depending on which of these structures the batteries are grounded to. DO NOT use solenoid mounting studs (5), washers (4), or nuts (6) as a connection point for the ground wire.
Cat SIS web machinery list:
Parts kit Caterpillar catalog:
2763420
KIT-GASKET
3054E, 416D, 416E, 420E, 424D, 428D, 914G, C4.4, CB-434D, CS-433E, IT14G, PF-300C, TH210, TH215
3054E, 416D, 416E, 420E, 424D, 428D, 914G, C4.4, CB-434D, CS-433E, IT14G, PF-300C, TH210, TH215
3342318
KIT-PISTON RING
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 4...
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 4...
3342319
KIT-PISTON RING
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 4...
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 4...
2332628
KIT-SEAL
414E, 416D, 416E
414E, 416D, 416E
2332623
KIT-SEAL
416D, 416E, 420D, 420E, 430D, 430E
416D, 416E, 420D, 420E, 430D, 430E
2332622
KIT-SEAL
416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, 446D, 527
416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, 446D, 527
2681964
KIT-SERVICE METER
120H, 12H, 135H, 140H, 160H, 307D, 311D LRR, 312C, 312D, 312D L, 314D LCR, 315C, 315D L, 318C, 319C, 319D, 319D L, 320C, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LC...
120H, 12H, 135H, 140H, 160H, 307D, 311D LRR, 312C, 312D, 312D L, 314D LCR, 315C, 315D L, 318C, 319C, 319D, 319D L, 320C, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LC...
2309357
KIT-SEAL
414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 428E, 428F, 430D, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 446D, 450E, 450F
414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 428E, 428F, 430D, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 446D, 450E, 450F
2764172
KIT-SEAL
307D, 308D, 308E, 308E2 CR, 416D, 416E, 416F, 420D, 420E, 420F, 430D, 430E, 430F, 450E, 450F
307D, 308D, 308E, 308E2 CR, 416D, 416E, 416F, 420D, 420E, 420F, 430D, 430E, 430F, 450E, 450F
3341997
KIT-PISTON RING
3054C, 3054E, 416D, 416E, 422E, 422F, AP-300, C4.4, CB-434D, CS-323C, CS-423E, TH210, TH215
3054C, 3054E, 416D, 416E, 422E, 422F, AP-300, C4.4, CB-434D, CS-323C, CS-423E, TH210, TH215
1778782
KIT-WATER PUMP
3054, 3054B, 3056, 3056E, 312C, 315B L, 550B, 554, 560B, 564, 574B, BG-225C, CS-563E, M312, M315
3054, 3054B, 3056, 3056E, 312C, 315B L, 550B, 554, 560B, 564, 574B, BG-225C, CS-563E, M312, M315
1769170
KIT-GAS SPRING
910G, 914G, 928G, 938G, CP-433E, CP-44, CP-533E, CP-56, CP-573E, CP-64, CP-663E, CP-76, CS-423E, CS-433E, CS-44, CS-531D, CS-533D, CS-533E, CS-54, CS-56, CS-563D, CS-563E, CS-573D, CS-583D, CS-583E, C...
910G, 914G, 928G, 938G, CP-433E, CP-44, CP-533E, CP-56, CP-573E, CP-64, CP-663E, CP-76, CS-423E, CS-433E, CS-44, CS-531D, CS-533D, CS-533E, CS-54, CS-56, CS-563D, CS-563E, CS-573D, CS-583D, CS-583E, C...
1663786
KIT-GASKET
3054, 3054B, 416D, 424D, 908, CP-433E
3054, 3054B, 416D, 424D, 908, CP-433E
1871290
KIT-GASKET
3054B, 416D, 424D, CS-423E, TH210, TH215
3054B, 416D, 424D, CS-423E, TH210, TH215
1883882
KIT-SEAL
TH103
TH103
2165574
KIT-SEAL
TH103, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
TH103, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2077822
KIT-SEAL
TH103
TH103
2077821
KIT-SEAL
TH103
TH103
2342593
KIT-SEAL
414E, 416D, 416E, 424D
414E, 416D, 416E, 424D
2350973
KIT-SEAL
416D, 420D, 428D, 432D, 438D, 442D
416D, 420D, 428D, 432D, 438D, 442D
2235945
KIT-SEAL
416D
416D
2012157
KIT-SERVICE
416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D
416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D
1850111
KIT-PISTON RING
3054B, 416D, 424D, CS-423E, TH210, TH215
3054B, 416D, 424D, CS-423E, TH210, TH215
1850110
KIT-PISTON RING
3054B, 416D, 424D, CS-423E, TH210, TH215
3054B, 416D, 424D, CS-423E, TH210, TH215