1871481 KIT-UNLOADER Caterpillar parts
3176C, 3196, 3406B, 3406C, 3406E, 3456, C-10, C-12, C-15, C-16, C-18, C16, C18
Rating:
Alternative (cross code) number:
CA1871481
187-1481
1871481
CA1871481
187-1481
1871481
Weight: 0.70 pounds 0 kg.
INDUSTRIAL ENGINE, TRUCK ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
10 Jan 2018
99 Hundredths Pounds
CTP: CTP
Caterpillar Kit-Unloader (1871481) New Aftermarket By CTP
1871481 Caterpillar, Engine Parts Weight(lbs): 1.00 Length(cm): 11.9000 Width(cm): 3.0000 Depth(cm): 12.1000
1871481 Caterpillar, Engine Parts Weight(lbs): 1.00 Length(cm): 11.9000 Width(cm): 3.0000 Depth(cm): 12.1000
Compatible equipment models: 1871481:
Information:
(1) Thickness of thrust plates (new) ... 5.461 0.038 mm (.2150 .0015 in)(2) Diameter of the main bearing journals (new) ... 88.880 0.020 mm (3.4992 .0008 in)(3) Diameter of the connecting rod journals (new) ... 76.180 0.020 mm (2.9992 .0008 in)(4) Tighten plugs to a torque of ... 23 4 N m (17 3 lb ft) Then "stake" the crankshaft to hold plugs in place. "STAKE" use a center punch and a hammer to change the shape of the holes as shown.(5) Crankshaft gear: Do not heat gear to more than ... 316°C (600°F)(6) End play for crankshaft (new) ... 0.122 to 0.579 mm (.0048 to .0228 in)(7) Wear sleeve and seal installation:Remove front and rear seal groups as follows: Seals and wear sleeves cannot be used again, after the seals and wear sleeves are separated.a. Use the 1P3075 Puller Group to remove the seals.b. Use the 5P7318 Distorter Group to remove the wear sleeves.Install front and rear seal groups as follows:a. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer.b. Crankshaft seals must be installed with the lip of the seals as shown. Make sure the correct seal is installed on each end of the crankshaft. No lubrication is needed to install wear sleeves and seals.c. Do not separate seals from sleeves. Install the seal groups as a unit on each end of the engine as shown with the correct tools. See Special Instruction Form No. SMHS7100 for installation of seal assemblies that do not have hydrodynamic grooves. Special Instruction Form No. SMHS8508 is used for hydrodynamic seal assembly installation.
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
2486740
KIT-GASKET
3406E, C-15, C15
3406E, C-15, C15
1541642
KIT-GASKET
3406E, 834G, 836G, C-16
3406E, 834G, 836G, C-16
1905978
KIT-GASKET
C-15
C-15
2341633
KIT-GASKET
C-15
C-15
2138113
KIT-GASKET
C-15
C-15
2220895
KIT-GASKET
C-15
C-15
2486744
KIT-GASKET
C-15
C-15
2525655
KIT-GASKET
C-15
C-15
2525656
KIT-GASKET
C-15
C-15
2572754
KIT-GASKET
C-15
C-15
2435142
KIT-GASKET
C-12
C-12
2434690
KIT-GASKET
C-12
C-12
1728179
KIT-GASKET
3126B, C-10, C-12
3126B, C-10, C-12
1789293
KIT-GASKET
C-10, C-12
C-10, C-12
1783664
KIT-GASKET
C-10
C-10
2053615
KIT-GASKET
C-10
C-10
1621437
KIT-GASKET
C-10, C-12
C-10, C-12
1728176
KIT-GASKET
C-10, C-12
C-10, C-12
2213886
KIT-GASKET
C-12
C-12
2213444
KIT-GASKET
C-10, C-12
C-10, C-12
1349809
KIT-GASKET
C-12
C-12
1644583
KIT-GASKET
C-12
C-12
1560942
KIT-GASKET
345B L, C-10, C-12
345B L, C-10, C-12
1871483
KIT-CYLINDER HEAD
3176C, 3196, 3406B, 3406C, 3406E, 3456, C-10, C-12, C-15, C-16, C-18, C16, C18
3176C, 3196, 3406B, 3406C, 3406E, 3456, C-10, C-12, C-15, C-16, C-18, C16, C18