1966934 KIT-GASKET Caterpillar parts
3126, 3126B, 3126E
Rating:
Alternative (cross code) number:
CA1966934
196-6934
1966934
CA1966934
196-6934
1966934
INDUSTRIAL ENGINE, TRUCK ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Irwin Tools 1966934 Irwin Marples Wood Drilling Forstner Bit, 1-1/2",
IRWIN Drills flat-bottomed and pocket holes in significantly less time than traditional Forstner bits || Features optimized ultra-sharp knife edge design specifically engineered to cut through hard and soft woods smoothly and efficiently || Easily drills high-quality flat-bottomed and pocket holes with a fine, smooth finish || Reduced shank fits 3/8" and larger drills and drill presses || Ideal for fine woodworking, cabinet-making, and more
IRWIN Drills flat-bottomed and pocket holes in significantly less time than traditional Forstner bits || Features optimized ultra-sharp knife edge design specifically engineered to cut through hard and soft woods smoothly and efficiently || Easily drills high-quality flat-bottomed and pocket holes with a fine, smooth finish || Reduced shank fits 3/8" and larger drills and drill presses || Ideal for fine woodworking, cabinet-making, and more
Irwin 1966934 1-1/2" Forstner Wood Boring Bit
For full view, you need register
Compatible equipment models: 1966934:
Information:
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1 Start By:
Remove the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00772036
Identify the position of clips (3) before removing the bolts. Note: Bolts (1) are different lengths.
Remove bolts (1) and (4).
Remove bonnet (2). Note: The bonnet on the opposite end of the aftercooler core is removed by the same procedure.
Illustration 2 g00772040
Clean the individual cores on aftercooler (5) with a 9.53 mm (0.375 inch) rod.
Illustration 3 g00772041
Remove bolts (8) and brackets (6) and (7).
Illustration 4 g00772044
Install Tooling (A) and attach a suitable lifting device on housing (9). Remove the bolts. There are four bolts that fasten mounting plate (10) to housing (9). Remove housing (9). The weight of housing (9) is 61 kg (135 lb).
The housing on the opposite side of the aftercooler core is removed by the same procedure.
Illustration 5 g00772045
Inspect core (11) for damage or for blockage of foreign matter.
Do not remove bolts (12) from plate (10). Bolts (12) cannot be installed with housing (9) in position.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1 Start By:
Remove the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00772036
Identify the position of clips (3) before removing the bolts. Note: Bolts (1) are different lengths.
Remove bolts (1) and (4).
Remove bonnet (2). Note: The bonnet on the opposite end of the aftercooler core is removed by the same procedure.
Illustration 2 g00772040
Clean the individual cores on aftercooler (5) with a 9.53 mm (0.375 inch) rod.
Illustration 3 g00772041
Remove bolts (8) and brackets (6) and (7).
Illustration 4 g00772044
Install Tooling (A) and attach a suitable lifting device on housing (9). Remove the bolts. There are four bolts that fasten mounting plate (10) to housing (9). Remove housing (9). The weight of housing (9) is 61 kg (135 lb).
The housing on the opposite side of the aftercooler core is removed by the same procedure.
Illustration 5 g00772045
Inspect core (11) for damage or for blockage of foreign matter.
Do not remove bolts (12) from plate (10). Bolts (12) cannot be installed with housing (9) in position.
Cat SIS web machinery list:
Parts kit Caterpillar catalog:
3126B, C-10, C-12
3126, 3126B, 3126E
3126B, 3126E
3126, 3126B, 3126E
3126B, 3126E
3126B, 3126E
3126B, 3126E
3126B, 3126E
3126B, 3126E
3126, 3126B, 3126E, 938F, IT38F
3126B, 3126E
3126B, 3126E
3126
3126, 3126E
3116, 3126
3126
1594539
KIT-GASKET
3126
3126
2107439
KIT-GASKET
3126
3126
3056
3508, 3508B
3754052
KIT-IMPELLER
3126B, C7, C9
3126B, C7, C9
3723373
KIT-SEAL
3126B, C7, C9
3126B, C7, C9
3126
2107444
KIT-GASKET
3126
3126