1997426 KIT-SEAL Caterpillar parts
320B, 322B LN, 325B L, 345B L
Rating:
Alternative (cross code) number:
CA1997426
199-7426
1997426
CA1997426
199-7426
1997426
Weight: 0.58 pounds 0 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
199-7426 Bucket Cylinder Seal Kit Fits E322B,322Bl,1997426
THREETREES Seal Kit
THREETREES Seal Kit
Kit King - CAT Caterpillar 1997426 Aftermarket Hydraulic Cylinder Seal Kit
Kit King USA 90 mm Rod & 130 mm Bore || Caterpillar Equipment Types: Excavators || Compatible Equipment Models: 325B, 325B L, 325B LN, 345B, 345B L, 345B LC and More || Typical Hydraulic Applications: Bucket || Fits Caterpillar Cylinder Models: 1184008, 1184166, 1232044, 1497610, 1505913, 1788449, 2033057, 7I1345 and More
Kit King USA 90 mm Rod & 130 mm Bore || Caterpillar Equipment Types: Excavators || Compatible Equipment Models: 325B, 325B L, 325B LN, 345B, 345B L, 345B LC and More || Typical Hydraulic Applications: Bucket || Fits Caterpillar Cylinder Models: 1184008, 1184166, 1232044, 1497610, 1505913, 1788449, 2033057, 7I1345 and More
$56.04
02 May 2024
Amazon.com
Kit King - CAT Caterpillar 1997426 Aftermarket Hydraulic Cylinder Seal Kit
Kit King USA 90 mm Rod & 130 mm Bore || Caterpillar Equipment Types: Excavators || Compatible Equipment Models: 325B, 325B L, 325B LN, 345B, 345B L, 345B LC and More || Typical Hydraulic Applications: Bucket || Fits Caterpillar Cylinder Models: 1184008, 1184166, 1232044, 1497610, 1505913, 1788449, 2033057, 7I1345 and More
Kit King USA 90 mm Rod & 130 mm Bore || Caterpillar Equipment Types: Excavators || Compatible Equipment Models: 325B, 325B L, 325B LN, 345B, 345B L, 345B LC and More || Typical Hydraulic Applications: Bucket || Fits Caterpillar Cylinder Models: 1184008, 1184166, 1232044, 1497610, 1505913, 1788449, 2033057, 7I1345 and More
Number on catalog scheme:
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6K-0806 Cable Strap 3
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01288986
typical example
Illustration 2 g01250795
typical example
Illustration 3 g01288996
typical example
Apply clean engine lubricating oil to both ends of the pushrods (4). Install the pushrods (4). Note: Ensure that the pushrods (4) are installed in the original location and that the pushrods are seated in the valve lifters correctly.
If the rocker shaft was disassembled, install the Tooling (A) around the rocker arms (2) in order to slightly compress spring (3). The rocker arms (1) must be held away from the machined face of the cylinder head (5) during reassembly.
Loosen the nut (6) and the adjustment screw (7) on each rocker arm. This will help prevent a bent valve or a bent pushrod during the installation of the rocker shaft.
Position the rocker shaft assembly on the cylinder head. Note: The rocker shaft (3) of the rocker shaft assembly is not symmetrical. The rocker shaft (3) has a machined flat at the front end of the shaft. Ensure that the machined flat is toward the top and toward the front end of the engine.
Install the Torx screws (9) in the rocker shaft (3). Note: The longest Torx screw must be installed at the front of the cylinder head in the hole (X).
Ensure that the adjustment screws (7) are properly seated in the ends of the pushrods (6).
Alternately tighten the Torx screws (9). Start from the center and work toward the outside. Tighten the Torx screws (9) to a torque of 35 3.5 N m (25.8 2.6 lb ft).
Cut and remove the Tooling (A) from the rocker shaft assembly.
Adjust the inlet valve lash to 0.20 mm (0.008 inch) and adjust the exhaust valve lash to 0.45 mm (0.018 inch). Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for more information on adjusting the valve lash. End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6K-0806 Cable Strap 3
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01288986
typical example
Illustration 2 g01250795
typical example
Illustration 3 g01288996
typical example
Apply clean engine lubricating oil to both ends of the pushrods (4). Install the pushrods (4). Note: Ensure that the pushrods (4) are installed in the original location and that the pushrods are seated in the valve lifters correctly.
If the rocker shaft was disassembled, install the Tooling (A) around the rocker arms (2) in order to slightly compress spring (3). The rocker arms (1) must be held away from the machined face of the cylinder head (5) during reassembly.
Loosen the nut (6) and the adjustment screw (7) on each rocker arm. This will help prevent a bent valve or a bent pushrod during the installation of the rocker shaft.
Position the rocker shaft assembly on the cylinder head. Note: The rocker shaft (3) of the rocker shaft assembly is not symmetrical. The rocker shaft (3) has a machined flat at the front end of the shaft. Ensure that the machined flat is toward the top and toward the front end of the engine.
Install the Torx screws (9) in the rocker shaft (3). Note: The longest Torx screw must be installed at the front of the cylinder head in the hole (X).
Ensure that the adjustment screws (7) are properly seated in the ends of the pushrods (6).
Alternately tighten the Torx screws (9). Start from the center and work toward the outside. Tighten the Torx screws (9) to a torque of 35 3.5 N m (25.8 2.6 lb ft).
Cut and remove the Tooling (A) from the rocker shaft assembly.
Adjust the inlet valve lash to 0.20 mm (0.008 inch) and adjust the exhaust valve lash to 0.45 mm (0.018 inch). Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for more information on adjusting the valve lash. End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
120H NA, 320B, 325B L, M325B
320B, 325B L, M325B
320 L, 320B, 320N, 325, 325 L, 325B L
320B, 320C, 330C L
330C, 345B II, 345B L, 350, M325C MH, M325D L MH
330, 330B L, 345B II, 345B L
330B, 330B L, 345B, 345B L
325B L, 345B L
330B L, 345B II, 345B L, 365B, 365B II, 385B
325B L, 328D LCR, 330B, 330B L, 345B L
345B II, 345B L
345B II, 345B L, 365B
322B LN, 322C, 325B L
322 LN, 322B LN, 325 LN
1155022
KIT-CONNECTOR
320B FM LL, 322B L, 325B L, 330B L
320B FM LL, 322B L, 325B L, 330B L
3287756
KIT-TOOL
322B L, 322C FM, 325B L, 330B L, CTV20
322B L, 322C FM, 325B L, 330B L, CTV20
3280412
KIT-SEAL
322B L, 322C FM, 325B L, 330B L, CTV20
322B L, 322C FM, 325B L, 330B L, CTV20
2002667
KIT-SEAL
322B L, 322C FM, 325B L, 330B L, GH52
322B L, 322C FM, 325B L, 330B L, GH52
6C6191
KIT-SEAL
320 L, 320B, 320C, 322 LN, 322B LN, 322C, 325 LN, 325B L, 325C, 330B L, 330C, 330C L
320 L, 320B, 320C, 322 LN, 322B LN, 322C, 325 LN, 325B L, 325C, 330B L, 330C, 330C L
1486615
KIT-SHIM
320B, 322B LN, 325B L, 330B L, 345B II, 345B L, 345C L
320B, 322B LN, 325B L, 330B L, 345B II, 345B L, 345C L
1486612
KIT-SEAL
320B, 322B LN, 325B L, 330B L, 345B II, 345B L, 345C L
320B, 322B LN, 325B L, 330B L, 345B II, 345B L, 345C L
322B LN, 325B, 325B L, 330B, 330B L, M325B, W330B
1390, 320B, 320C, 322B LN, 322C, 325C, 325C FM, 325D, 325D FM, 325D L, 330C, 330C MH, 330D L, 330D MH, 336D LN, 345B II, 345C L, 365B, 365B II, 365C, 365C L, 385B, 385C L, 541, 551, 552, M322C, M322D,...
320B, 322B LN