KIT-SEAL- 2293635 - Caterpillar

2293635 KIT-SEAL- Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2293635
229-3635
2293635

Weight: 0.87 pounds 0 kg.

Buy KIT-SEAL- 2293635 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Cooling System Engine Parts Fan Clutch Compatible with DA-F 1910613 2325565 2046260 2178414 2293635

$939.69

14 Oct 2025
0.1102[0.05] Pounds
CN: jichenqipeidian

Cooling System Engine Parts Fan Clutch Compatible with DA-F 1910613 2325565 2046260 2178414 2293635
LXXMZJT Cooling System Engine Parts Fan Clutch Compatible with DA-F 1910613 2325565 2046260 2178414 2293635 || Reduce mechanical wear: Silicone oil lubrication reduces the wear of clutch components, lowering maintenance frequency and costs || Low-temperature start-up optimization: The electronic control system can pre-adjust the fan speed according to the ambient temperature, shortening the warm-up time || On-demand heat dissipation: Only activate the silicone oil drive when the temperature rises, avoiding energy waste caused by the continuous operation of traditional fans || Reduce noise by 1-2 decibels: When the fan operates at a low speed, the noise is even lower, enhancing the comfort of the cab and reducing driver fatigue

For full view, you need register

Information:

To prevent possible personal injury, make sure the pressure in the air system is zero before any air lines are disconnected.
3. Put identification marks on the two air lines for correct installation. Disconnect the two air lines from governor control valve (1). 4. Remove clip (3) and pin (2) that holds the pedal to the plate. Remove pedal (4). 5. Remove clip (6) from the pin. Remove pin (7) and roller (5) from the pedal. 6. Remove spring (8). Remove the rubber and plunger (9). 7. Remove nut (11) that holds the governor control valve in position. Remove the governor control valve.8. Remove three bolts (10) and plate (12).Install Governor Control Valve
1. Put plate (12) in position, and install three bolts (10) that hold it to the floor plate. 2. Put governor control valve (1) in position, and install nut (11) from the inside of the cab to hold it in place. 3. Install spring (8) on the plate. Install rubber and plunger (9) on top of the valve.4. Connect the two air lines to governor control valve (1). 5. Put roller (5) in the pedal. Install pin (7) to hold the roller in the pedal. Install clip (6) on the pin. 6. Put pedal (4) in position on the plate, and install pin (2).7. Install clip (3) that holds pin (2) in place.Disassemble And Assemble Governor Control Valve
Start By:a. remove governor control valve 1. Remove six screws (1) that hold the governor control valve together. 2. Remove cover (9), O-ring seal (8), valve (7), seals (6), piston (5), shims (4) and spring (3) from housing (2). Remove the O-ring seal from inside cover (9). The following steps are for assembly of the governor control valve.3. Make sure all parts are clean. Put clean oil on all the seals. If the valve is defective, it must be replaced as a unit.4. Install the O-ring seal inside cover (9).5. Install spring (3), shims (4), piston (5), seals (6), and valve (7) into housing (2).6. Install O-ring (8) and cover (9) on housing (2).7. Install screws (1) that hold the governor control valve together.End By:a. install governor control valve