2410109 KIT-SEAL- Caterpillar parts
Rating:
Alternative (cross code) number:
CA2410109
241-0109
2410109
CA2410109
241-0109
2410109
Weight: 0.26 pounds 0 kg.
You can buy:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Polaris 2410109 Switch Ignition Ranger 500
Polaris OEM Polaris Product, Part Number: 2410109 || See product description below for vehicle fitment or to verify fitment for your specific vehicle, please contact us, and provide us with your VIN that can be found on your vehicle or your insurance || For schematic location 22 only
Polaris OEM Polaris Product, Part Number: 2410109 || See product description below for vehicle fitment or to verify fitment for your specific vehicle, please contact us, and provide us with your VIN that can be found on your vehicle or your insurance || For schematic location 22 only
2410109 Ignition Switch w/ 2 Keys For Polaris 1999 Ranger 500 6x6
Generic MPN：2410109 || Ignition Switch w/ 2 Keys For Polaris 1999 Ranger 500 6x6 A99RF50AA Instrument Panel || Specification:3 Positions；5 Terminals || Package List：Ignition Switch *1
Generic MPN：2410109 || Ignition Switch w/ 2 Keys For Polaris 1999 Ranger 500 6x6 A99RF50AA Instrument Panel || Specification:3 Positions；5 Terminals || Package List：Ignition Switch *1
Polaris 2410109 Switch Ignition Ranger 500
Polaris OEM Polaris Product, Part Number: 2410109 || See product description below for vehicle fitment or to verify fitment for your specific vehicle, please contact us, and provide us with your VIN that can be found on your vehicle or your insurance || For schematic location 22 only
Polaris OEM Polaris Product, Part Number: 2410109 || See product description below for vehicle fitment or to verify fitment for your specific vehicle, please contact us, and provide us with your VIN that can be found on your vehicle or your insurance || For schematic location 22 only
For full view, you need register
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
C 248-3311 Holding Fixture 1
D 248-3310 Spanner Wrench 1
E 8H-0663 Bearing Puller Gp 1
F 369-9451 O-Ring Assembly Compound -
G 7N-8268 Installation Tool 1
H 8H-8581 Feeler Gauge 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g06146290
Use Tooling (E) and a suitable press to install bearing assembly (17) on pump shaft (12).
Install bearing cone (21) on the pump shaft.
Install spacer (20) and bearing cups (19) on the pump shaft.
Install bearing cone (18) on the pump shaft.
Illustration 2 g06146285
The splined end of the pump shaft is marked to indicate either RH threads or LH threads on pump shaft (12). Install bearing locknut (16). Use Tooling (D) on bearing locknut (16). Tighten bearing locknut (16) to a torque of 300 30 N m (221 22 lb ft).Note: The torque wrench must be 90 degrees to Tooling (D).
Install set screws (15) and tighten to a torque of 4 1.25 N m (35 114 lb in) in a 180° pattern then retighten to a final torque of 7.2 0.2 N m (67 1.8 lb in).
Illustration 3 g06146275
Lubricate pump shaft (12) with clean engine oil. Install the pump shaft in bearing housing (14). Install seal (13). Install retainer (10) and bolts (11). Tighten bolts (11) to a torque of 12 3 N m (106 27 lb in).
Illustration 4 g06141846Note: Do not damage the wear surfaces of the carbon ring or the ceramic ring. Do not touch the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal.
Apply Tooling (F) to the outside diameter of the ceramic seal (13). Use Tooling (G) and hand pressure to install ceramic seal (13) into the bearing housing and the shaft. Installed height should be 9.9 0.38 cm (3.9 0.15 inch).
Illustration 5 g06037413
Lubricate pump shaft (12) on bearing housing (9) with clean engine oil. Position impeller (8) on pump shaft (12).
Place bearing housing (9) on impeller (8). Use a suitable press and press pump shaft (12) into impeller (8). Install impeller (8) so the dimension between impeller (8) and pump shaft (12) is 0.000 0.15 mm (0.00000 0.0.030 inch).
Illustration 6 g06196067
Install O-ring seal (6) on the bearing housing. Lubricate the O-ring seal with clean engine oil.
Position the bearing housing in pump housing (7). Install bolts (5) finger tight.
Illustration 7 g06037556
Tighten bolts (5) in the numerical sequence shown in illustration 7 to a torque of 50 9 N m (37 7 lb ft).
Use Tooling (H) and measure the gap between impeller (8) and pump housing (7). The minimum gap between impeller (8) and pump housing (7) is 0.20 mm (0.008 inch).
Illustration 8 g06196068
Install plug (4), plug (3), water pump filter (2), and plug (1).End By:
Install water pump.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
C 248-3311 Holding Fixture 1
D 248-3310 Spanner Wrench 1
E 8H-0663 Bearing Puller Gp 1
F 369-9451 O-Ring Assembly Compound -
G 7N-8268 Installation Tool 1
H 8H-8581 Feeler Gauge 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g06146290
Use Tooling (E) and a suitable press to install bearing assembly (17) on pump shaft (12).
Install bearing cone (21) on the pump shaft.
Install spacer (20) and bearing cups (19) on the pump shaft.
Install bearing cone (18) on the pump shaft.
Illustration 2 g06146285
The splined end of the pump shaft is marked to indicate either RH threads or LH threads on pump shaft (12). Install bearing locknut (16). Use Tooling (D) on bearing locknut (16). Tighten bearing locknut (16) to a torque of 300 30 N m (221 22 lb ft).Note: The torque wrench must be 90 degrees to Tooling (D).
Install set screws (15) and tighten to a torque of 4 1.25 N m (35 114 lb in) in a 180° pattern then retighten to a final torque of 7.2 0.2 N m (67 1.8 lb in).
Illustration 3 g06146275
Lubricate pump shaft (12) with clean engine oil. Install the pump shaft in bearing housing (14). Install seal (13). Install retainer (10) and bolts (11). Tighten bolts (11) to a torque of 12 3 N m (106 27 lb in).
Illustration 4 g06141846Note: Do not damage the wear surfaces of the carbon ring or the ceramic ring. Do not touch the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal.
Apply Tooling (F) to the outside diameter of the ceramic seal (13). Use Tooling (G) and hand pressure to install ceramic seal (13) into the bearing housing and the shaft. Installed height should be 9.9 0.38 cm (3.9 0.15 inch).
Illustration 5 g06037413
Lubricate pump shaft (12) on bearing housing (9) with clean engine oil. Position impeller (8) on pump shaft (12).
Place bearing housing (9) on impeller (8). Use a suitable press and press pump shaft (12) into impeller (8). Install impeller (8) so the dimension between impeller (8) and pump shaft (12) is 0.000 0.15 mm (0.00000 0.0.030 inch).
Illustration 6 g06196067
Install O-ring seal (6) on the bearing housing. Lubricate the O-ring seal with clean engine oil.
Position the bearing housing in pump housing (7). Install bolts (5) finger tight.
Illustration 7 g06037556
Tighten bolts (5) in the numerical sequence shown in illustration 7 to a torque of 50 9 N m (37 7 lb ft).
Use Tooling (H) and measure the gap between impeller (8) and pump housing (7). The minimum gap between impeller (8) and pump housing (7) is 0.20 mm (0.008 inch).
Illustration 8 g06196068
Install plug (4), plug (3), water pump filter (2), and plug (1).End By:
Install water pump.
Parts kit Caterpillar catalog:
2410108
KIT-SEAL-
Caterpillar
Caterpillar
Caterpillar
Caterpillar
2409650
KIT-
Caterpillar
Caterpillar
2409649
KIT-GASKET-MCH
Caterpillar
Caterpillar
2409648
KIT-GASKET-SCH
Caterpillar
Caterpillar
Caterpillar
Caterpillar
2410487
KIT-AIR
Caterpillar
Caterpillar
Caterpillar
2410137
KIT-GASKET-MCH
Caterpillar
Caterpillar
2410136
KIT-GASKET-FS
Caterpillar
Caterpillar