2590678 KIT-SEAL Caterpillar parts
320D, 324D, 324D L
Rating:
Alternative (cross code) number:
CA2590678
259-0678
2590678
CA2590678
259-0678
2590678
Weight: 0.49 pounds 0 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
259-0776 259-0678 464-2933 Cylinder Seal Kit for Caterpillar 323 E324D 326D
HQPA
HQPA
259-0776 259-0678 464-2933 Cylinder Seal Kit for Caterpillar 323 E324D 326D
HQPA
HQPA
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Support the engine.
Install a suitable lifting device to the flywheel housing. Support the weight of the housing. The weight of the flywheel housing is approximately 30 kg (66 lb).
Illustration 1 g01326591
Illustration 2 g01305649
Typical example
Remove bolts (3) and (4) that fasten flywheel housing (8) to the cylinder block.
Remove bolts (6) on each side of the cylinder block. These bolts fasten flywheel housing (8) to the cylinder block.
Remove bolts (1) that fasten back plate (2) to flywheel housing (8).
Remove nuts (5) and the bolts (not shown) that fasten back plate (2) to flywheel housing (8).
Carefully remove flywheel housing (8) from back plate (2) and dowels (7). Use a suitable lifting device to remove the flywheel housing. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the mating surfaces of back plate (2) and flywheel housing (8) are clean and free from damage. Inspect the crankshaft rear seal (not shown) for leaks. If necessary, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure. Inspect dowels (7) for damage. If the dowels are damaged, use new parts for replacement.
Illustration 3 g01305649
Illustration 4 g01326591
Typical example
Use a suitable lifting device to align flywheel housing (8) to dowels (7). The weight of the flywheel housing is approximately 30 kg (66 lb). Install the flywheel housing to the back plate.
Install nuts (5) and the bolts (not shown) that fasten back plate (2) to flywheel housing (8).
Install bolts (1) that fasten back plate (2) to flywheel housing (8).
Install bolts (6) on each side of the cylinder block. These bolts fasten flywheel housing (8) to the cylinder block.
Remove the lifting device from the flywheel housing.
Install bolts (3) and (4) that fasten flywheel housing (8) to the cylinder block.
Tighten the fasteners to a torque of 25 N m (19 lb ft). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Support the engine.
Install a suitable lifting device to the flywheel housing. Support the weight of the housing. The weight of the flywheel housing is approximately 30 kg (66 lb).
Illustration 1 g01326591
Illustration 2 g01305649
Typical example
Remove bolts (3) and (4) that fasten flywheel housing (8) to the cylinder block.
Remove bolts (6) on each side of the cylinder block. These bolts fasten flywheel housing (8) to the cylinder block.
Remove bolts (1) that fasten back plate (2) to flywheel housing (8).
Remove nuts (5) and the bolts (not shown) that fasten back plate (2) to flywheel housing (8).
Carefully remove flywheel housing (8) from back plate (2) and dowels (7). Use a suitable lifting device to remove the flywheel housing. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the mating surfaces of back plate (2) and flywheel housing (8) are clean and free from damage. Inspect the crankshaft rear seal (not shown) for leaks. If necessary, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure. Inspect dowels (7) for damage. If the dowels are damaged, use new parts for replacement.
Illustration 3 g01305649
Illustration 4 g01326591
Typical example
Use a suitable lifting device to align flywheel housing (8) to dowels (7). The weight of the flywheel housing is approximately 30 kg (66 lb). Install the flywheel housing to the back plate.
Install nuts (5) and the bolts (not shown) that fasten back plate (2) to flywheel housing (8).
Install bolts (1) that fasten back plate (2) to flywheel housing (8).
Install bolts (6) on each side of the cylinder block. These bolts fasten flywheel housing (8) to the cylinder block.
Remove the lifting device from the flywheel housing.
Install bolts (3) and (4) that fasten flywheel housing (8) to the cylinder block.
Tighten the fasteners to a torque of 25 N m (19 lb ft). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
120M, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14H, 14H NA, 14M, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673C, 16G, 16H, 16H NA, 16M, 2290, 2390, 2391, 2491, 259...
140G, 303.5C, 303C CR, 304C CR, 305C CR, 312D, 312D L, 314D LCR, 315D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D L, 320D LRR, 320D RR, 321D LCR, 322C FM, 323D L, 323D LN, 323D SA, 324D FM, 324D FM LL...
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2390, 2391, 2470C, 2491, 24M, 257...
3126E, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336...
311C, 312C, 312C L, 314C, 320C, 320D, 322C, 323D L, 324D, 324D L, 325C, 325C L, 325D, 325D L, 329D L, 330C, 330C L
324D, 324D L
324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 329E L, 329E LN
320D, 320D L, 320E L, 325D, 325D L, 328D LCR, 329D, 329D L
320D, 320D L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L
320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 323D L, 323D LN, 324D, 324D L
324D, 324D FM, 324D L, 324E, 324E L, 324E LN, 326D L
324D, 324D L
324D, 324D L
324D, 324D L
323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 325D, 325D FM, 325D L, 329D L, 329D LN, 330D L
320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 323D L, 323D LN, 323D SA, 324D, 324D L
320D, 320D FM, 320D FM RR, 320D L, 320D LRR, 320D RR, 323D L, 324D, 324D L
320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA, 324D, 324D L
320D, 324D, 324D L, 324E, 324E L, 324E LN, 326D L
2668014
KIT-SEAL
324D, 324D L
324D, 324D L
324D, 324D L