2591033 KIT-DT BEARING Caterpillar parts
Rating:
Alternative (cross code) number:
CA2591033
259-1033
2591033
CA2591033
259-1033
2591033
Weight: 125 pounds 56 kg.
Information:
1. Remove plate (1) from the hydraulic control lever console. 2. Disconnect linkage (2) from the lift control lever. Disconnect linkage (3) from the tilt control lever. 3. Remove knob (4) from the lift control lever. Remove the screws, bolts and washers to remove cover (5) and cover assembly (6) as a unit. 4. Loosen the bolts and remove lever (8) from the shaft of tilt control lever (9) and remove the lever from the shaft of lift control lever (7). Remove levers (7) and (9) with the shafts from the console. 5. If necessary, remove knob (10) and shaft (11) from tilt control lever (9). Remove the two keys (12) from shaft (11). 6. If necessary, remove shaft (14) from lift control lever (7). Remove the two keys (13) and shaft (14).Install Hydraulic Control Levers
1. If necessary, remove bearings (1) and use tool group (A) to make a replacement. Install the bearings for the control lever shafts so the seals in the bearings are to the outside. 2. Install keys (4) in shaft (3). Install shaft (3) and knob (2) on tilt control lever (5). 3. Install keys (7) in shaft (8) and install shaft (8) in lift control lever (6). 4. Put control levers (5) and (6) in position and install levers (11) on the control lever shafts.5. Install cover (9) and cover assembly (10) over the control levers.6. Install the knob on lift control lever (6). 7. Connect linkage (12) to lift control lever (6). Connect linkage (13) to tilt control lever (5). Make sure the hydraulic controls are in correct adjustment. See TESTING AND ADJUSTING section. 8. Install plate (14) on the lift and tilt control lever console.
1. If necessary, remove bearings (1) and use tool group (A) to make a replacement. Install the bearings for the control lever shafts so the seals in the bearings are to the outside. 2. Install keys (4) in shaft (3). Install shaft (3) and knob (2) on tilt control lever (5). 3. Install keys (7) in shaft (8) and install shaft (8) in lift control lever (6). 4. Put control levers (5) and (6) in position and install levers (11) on the control lever shafts.5. Install cover (9) and cover assembly (10) over the control levers.6. Install the knob on lift control lever (6). 7. Connect linkage (12) to lift control lever (6). Connect linkage (13) to tilt control lever (5). Make sure the hydraulic controls are in correct adjustment. See TESTING AND ADJUSTING section. 8. Install plate (14) on the lift and tilt control lever console.
Caterpillar SIS machinery equipment:
Parts kit Caterpillar catalog:
2591031
KIT-DT BEARING
Caterpillar
Caterpillar
2591012
KIT-DT BEARING
Caterpillar
Caterpillar
2591011
KIT-DT BEARING
Caterpillar
Caterpillar
2590307
KIT-SEAL-
Caterpillar
Caterpillar
2587781
KIT AR-STD ARM
Caterpillar
Caterpillar
2584655
KIT AR
Caterpillar
Caterpillar
2595514
KIT-DT BEARING
Caterpillar
Caterpillar
2591662
KIT-ENG ENCL
Caterpillar
Caterpillar
2591038
KIT -
Caterpillar
Caterpillar
2591037
KIT-DT GASKET
Caterpillar
Caterpillar
2591035
KIT-DT GASKET
Caterpillar
Caterpillar
2591034
KIT-DT GASKET
Caterpillar
Caterpillar