KIT-DT BEARING 2752320 - Caterpillar

Assembly Procedure
Illustration 2 g03833833
Abutment end cap after final assembly on track roller frame. (3) Solid abutment side (4) Gapped side
Verify that track roller frame mounting surfaces are clean and flat.
Slide the roller cap over the end of the shaft.
Place track rollers on track roller frame so that the flat part of the shaft is against the track roller frame.
Apply anti-seize to bolt threads. Install track roller bolts and washers through the cap and into the track frame.
Tighten bolt on the side (3) that is marked "Tighten First" to proper torque. Refer to Table 1 for proper torque.
Tighten the bolt on the gapped side (4) to the proper torque. Refer to Table 1 for proper torque.
A 2 mm (0.08 inch) to 3 mm (0.12 inch) gap will remain between cap and roller frame.
Repeat for the cap on other end of roller shaft.
Table 1
New Abutment Roller Cap Part Number     Roller Cap Bolt Diameter     New Roller Cap Bolt Part Number     Washer Part Number     Bolt Torque     TTT Model     Related IRM    
248-5323    
16 mm (0.63 inch)     8T-0357     9X-8268    
270 40 N m (199 30 lb ft)     D5K     TBD    
218-4993    
16 mm (0.63 inch)     137-3301     9X-8268    
270 40 N m (199 30 lb ft)     D5M
D5N
D6K     TBD    
223-9110    
15.88 mm (0.625 inch)     1B-4367     5P-8247    
240 40 N m (177 30 lb ft)     D5
D5B
D5C
D5D
D5H
953B
953C
D6     PELJ1038    
16 mm (0.63 inch) 8T-0281     9X-8268    
270 40 N m (199 30 lb ft)     D5H
953B
953C
D6M
D6N    
322-4691    
19.05 mm (0.75 inch)     1D-4610     5P-8248    
430 60 N m (317 44 lb ft)     D5H WITH 3/4" - 10     TBD    
20 mm (0.79 inch) 6V-3669     8T-3282    
520 70 N m (384 52 lb ft)     517 WITH M20X2.5     PELJ1038    
317-9078    
15.88 mm (0.625 inch)     1D-4585     2S-0736    
240 40 N m (177 30 lb ft)     D6C
D6D
955     PELJ0815    
317-9079    
19.05 mm (0.75 inch)     1D-4610     5P-8248    
430 60 N m (317 44 lb ft)     D6C
D6D
D6E
D6G
D6H
955
963    
317-9080    
20 mm (0.79 inch)     8T-0360     8T-3282    
520 70 N m (384 52 lb ft)     D6R
D6T
963
963B
963C    
360-9216    
20 mm (0.79 inch)     8T-0360     8T-3282    
520 70 N m (384 52 lb ft)     527     TBD    
273-3996    
22.23 mm (0.875 inch)     1D-4630     9H-1031    
750 90 N m (553 66 lb ft)     D7
572
973     PELJ1211    
222-7244    
24 mm (0.94 inch)     8T-0666     6V-8237    
900 10 N m (664 7 lb ft)    Note: Each roller requires two caps, four bolts, and four washers.Roller Cap And Bolt Re-Use Guidelines
Track roller caps