2934763 KIT-SEAL Caterpillar parts
CB-14
Rating:
Alternative (cross code) number:
CA2934763
293-4763
2934763
CA2934763
293-4763
2934763
Weight: 0.01 pounds 0 kg.
VIBRATORY COMPACTOR,
Compatible equipment models: 2934763:
Number on catalog scheme:
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
B FT-2806 Alignment Tool 1 Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02450219
Illustration 2 g02450222
Ensure that crankshaft flange (1) is clean, dry, and free from damage.
Ensure that the face of the cylinder block and the bridge piece are clean and dry.
A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic sleeve is squarely installed within crankshaft rear seal (2). Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is pushed over the crankshaft flange.Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry.
Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft flange. During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard the plastic sleeve.
Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder block. Ensure that the crankshaft rear seal is seated against the cylinder block.
Illustration 3 g02451996
Install torx screws (4) finger tight. Tightening sequence for the crankshaft rear sealNote: Do not install torx screws to Positions (X) at this stage.
Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1).
Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N m (16 lb ft). Tighten torx screws (4) in the sequence that is shown in Illustration 3.
Remove Tooling (B).
Install remaining torx screws (4) to Positions (X). Use Tooling (A) in order to tighten the torx screws to a torque of 22 N m (16 lb ft). Refer to Illustration 3. End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
B FT-2806 Alignment Tool 1 Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02450219
Illustration 2 g02450222
Ensure that crankshaft flange (1) is clean, dry, and free from damage.
Ensure that the face of the cylinder block and the bridge piece are clean and dry.
A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic sleeve is squarely installed within crankshaft rear seal (2). Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is pushed over the crankshaft flange.Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry.
Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft flange. During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard the plastic sleeve.
Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder block. Ensure that the crankshaft rear seal is seated against the cylinder block.
Illustration 3 g02451996
Install torx screws (4) finger tight. Tightening sequence for the crankshaft rear sealNote: Do not install torx screws to Positions (X) at this stage.
Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1).
Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N m (16 lb ft). Tighten torx screws (4) in the sequence that is shown in Illustration 3.
Remove Tooling (B).
Install remaining torx screws (4) to Positions (X). Use Tooling (A) in order to tighten the torx screws to a torque of 22 N m (16 lb ft). Refer to Illustration 3. End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct procedure.
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
3003, 3011C, C1.1, C1.6, CB-14, CB-214E, CB-334E
120H, 120H ES, 120H NA, 135H, 135H NA, 216, 216B, 216B3, 226B, 226B3, 232B, 236, 236B, 236B3, 242B, 242B3, 246C, 247B, 247B3, 252B, 252B3, 256C, 257B, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C...
120H, 120H ES, 120H NA, 135H, 135H NA, 216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 242B, 247, 247B, 247B3, 248, 257B, 267, 30/30, 301.5, 301.6C, 301.7D, 301.7D CR, 302.2D, 302.4D, 302.5, 302.5C, 30...
3044764
KIT-BEARING
3011C, 3013C, C1.1, CB-14
3011C, 3013C, C1.1, CB-14
3011C, 3013C, C1.1, C1.6, CB-14
3011C, 3013C, C1.1, C1.6, CB-14
AS4173, CB-14, CB-214D, CB-214E, CB-22, CB-224C, CB-334D, CB-334E, CB-335D, CB-34
CB-14, CB-214D, CB-214E, CB-22, CB-224C, CB-334D, CB-334E, CB-335D, CB-34, CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B, CP-433E, CP-573E, CP-663E, CS-423E, CS-433E, CS-531D, CS-533D, CS-533E, C...
2473253
KIT-VALVE HOUSING
CB-14, CB-214E, CB-22, CB-334E, CB-34
CB-14, CB-214E, CB-22, CB-334E, CB-34
2933731
KIT-VALVE
CB-14
CB-14
2933732
KIT-SEAL
CB-14
CB-14
3226338
KIT-SEAT BELT
CB-14
CB-14
3012865
KIT-SWITCH
CB-14, CB-22, CB-34
CB-14, CB-22, CB-34
2935769
KIT-SEAL
CB-14
CB-14
2933732
KIT-SEAL
CB-14
CB-14
2933731
KIT-VALVE
CB-14
CB-14
2933729
KIT-PUMP
CB-14
CB-14
2933730
KIT-COVER
CB-14
CB-14
2877720
KIT-SEAL
AS2252C, AS2302
AS2252C, AS2302
3226337
KIT-SEAT BELT
CB-14
CB-14
3226341
KIT-SEAT
CB-14
CB-14
3226340
KIT-CABLE
CB-14
CB-14
3226339
KIT-SLIDE RAIL
CB-14
CB-14
3226338
KIT-SEAT BELT
CB-14
CB-14