2N6057 KIT (Stator Rewind) Caterpillar parts
D398B, G398
Rating:
Alternative (cross code) number:
CA2N6057
2N-6057
2N6057
CA2N6057
2N-6057
2N6057
Weight: 3 pounds 1 kg.
GAS ENGINE, GEN SET ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$20.80
02 Feb 2023
US: We Have That It
2N6057 / Transistor / 2 Pieces / (qzty)
Generic 2N6057 / TRANSISTOR / 2 PIECES / (qzty) || Quality Electronic Components || Semiconductor || Orignal Listing by : We Have That Item Inc. "A trusted Supplier"
Generic 2N6057 / TRANSISTOR / 2 PIECES / (qzty) || Quality Electronic Components || Semiconductor || Orignal Listing by : We Have That Item Inc. "A trusted Supplier"
$12.32
11 Jul 2022
0.31[0.14] Pounds
US: Data Alchemy
Motorola 2N6057 Bipolar Single Transistor, NPN, 100 V, 150 W, 12 A
Motorola Test & Measurement
Motorola Test & Measurement
$12.32
10 Jul 2022
0.31[0.14] pounds
US: Data Alchemy
Motorola 2N6057 Bipolar Single Transistor, NPN, 100 V, 150 W, 12 A
Motorola Test & Measurement
Motorola Test & Measurement
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect". Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Illustration 1 g01361942
Rear hood removed for photographic purposes
Disconnect hose assembly (2) and the clip.
Remove cover (1) and the gasket.
Illustration 2 g01322546
Disconnect harness assembly (6) and hose assembly (3). Remove two bolts (5) and modulating valve (4).
Illustration 3 g01322547
Remove connector (11) and O-ring seals (10) and (12). Remove nut (7), washer (8), and coil assembly (9) from valve assembly (13).
Illustration 4 g01322557
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Note: This component is being disassembled and displayed for CLEANING PURPOSES ONLY. Many of the internal parts are not available for this component. Care must be taken during the disassembly and assembly in order to prevent damage to unavailable parts.
Remove cartridge assembly (14), spool (16) and spring (17) from body (15).
Repeat Steps 3 through 5 for the remaining modulating valves. Installation Procedure
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Illustration 5 g01322557
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install spring (17), spool (16) and cartridge assembly (14) into body (15). Tighten cartridge assembly (14) to a torque of 50 5 N m (37 4 lb ft).
Illustration 6 g01322547
Install coil (9), washer (8) and nut (7) to valve assembly (13). Tighten nut (7) to a torque of 13 1.5 N m (115 13 lb in). Install connector (11) and O-ring seals (10) and (12). Tighten connector (11) to a torque of 14 4 N m (10 3 lb ft).
Illustration 7 g01322546
Install modulating valve (4) and two bolts (5). Connect hose assembly (3), and tighten hose assembly (3) to a torque of 25 3 N m (18 2 lb ft). Connect harness assembly (6).
Repeat Steps 1 through 3 for the remaining modulating valves.
Illustration 8 g01361942
Rear hood removed for photographic purposes
Install the gasket and cover (1).
Connect hose assembly (2) and the clip. End By:
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect". Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Illustration 1 g01361942
Rear hood removed for photographic purposes
Disconnect hose assembly (2) and the clip.
Remove cover (1) and the gasket.
Illustration 2 g01322546
Disconnect harness assembly (6) and hose assembly (3). Remove two bolts (5) and modulating valve (4).
Illustration 3 g01322547
Remove connector (11) and O-ring seals (10) and (12). Remove nut (7), washer (8), and coil assembly (9) from valve assembly (13).
Illustration 4 g01322557
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Note: This component is being disassembled and displayed for CLEANING PURPOSES ONLY. Many of the internal parts are not available for this component. Care must be taken during the disassembly and assembly in order to prevent damage to unavailable parts.
Remove cartridge assembly (14), spool (16) and spring (17) from body (15).
Repeat Steps 3 through 5 for the remaining modulating valves. Installation Procedure
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Illustration 5 g01322557
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install spring (17), spool (16) and cartridge assembly (14) into body (15). Tighten cartridge assembly (14) to a torque of 50 5 N m (37 4 lb ft).
Illustration 6 g01322547
Install coil (9), washer (8) and nut (7) to valve assembly (13). Tighten nut (7) to a torque of 13 1.5 N m (115 13 lb in). Install connector (11) and O-ring seals (10) and (12). Tighten connector (11) to a torque of 14 4 N m (10 3 lb ft).
Illustration 7 g01322546
Install modulating valve (4) and two bolts (5). Connect hose assembly (3), and tighten hose assembly (3) to a torque of 25 3 N m (18 2 lb ft). Connect harness assembly (6).
Repeat Steps 1 through 3 for the remaining modulating valves.
Illustration 8 g01361942
Rear hood removed for photographic purposes
Install the gasket and cover (1).
Connect hose assembly (2) and the clip. End By:
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
3N9146
KIT-MARINE SPARE PARTS
D398A, D398B
D398A, D398B
D379, D379B, D398A, D398B, D399
1090, 1140, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673C, 1693, 16G, 16H NA, 16M, 215, 229...
594H, D353C, D379, D379B, D398, D398A, D398B, D399, D9H
D379B, D398, D398B
D379B, D398, D398A, D398B
7W1920
KIT-ROTOR BALANCE WEIGHT
3508, 3512, D379B, D398B, G3508, G3512, G3516, G379, G399, SR4
3508, 3512, D379B, D398B, G3508, G3512, G3516, G379, G399, SR4
G3306, G3306B, G398
G3304, G3306, G342C, G353D, G379, G398
6N0709
KIT (Seal)
G3304, G3306, G342C, G379, G398, G399
G3304, G3306, G342C, G379, G398, G399
5N9484
KIT (heater-space)
3508, 3512, 3516, D398B, D399, G398, SR4
3508, 3512, 3516, D398B, D399, G398, SR4
D398B
2N6793
KIT (Stator Rewind)
D379B, G379
D379B, G379
140B, 235, 955K, 955L, 966R, 977K, D6C, D6D