KIT-ADHESIVE 3083506 - Caterpillar

Table 1
Table for Customer Specified Parameter    
Parameter    Available Range or Options    Default    
"Selected Engine Rating"    
"Rating Number"     Dependent on engine power        
"ECM Identification Parameters"    
"Vehicle ID"     17 Digits
Available characters are dependent on the service tools.     all zeroes    
"Truck Manufacturer Parameters"    
"Truck Manufacturer"     "Other"     "Other"    
"Vehicle Speed Parameters"    
"Vehicle Speed Calibration"    
2485 to 93226 PPKM (4000 to 150000 PPM)     Not Programmed    
"Vehicle Speed CAL (J1939-Trans)"     0 to 43000 revolutions per km (0 to 65000 rpm)     Not Programmed    
"Vehicle Speed CAL (J1939-ABS)"     0 to 6.550     Not Programmed    
"Vehicle Speed Limit (VSL)"    
48 to 204 km/h (30 to 127 mph)    
204 km/h (127 mph)    
"VSL Protection"     1700 to TEL rpm     TEL rpm    
"Tachometer Calibration"     2.0 to 500.0 pulses per revolution     134.0 pulses per revolution    
"Soft Vehicle Speed Limit"     "No"
"Yes"     "No"    
"Low Speed Range Axle Ratio"     0.00 to 19.99     0.00    
"High Speed Range Axle Ratio"     0.0 to 9.99     0.00    
"Cruise Control Parameters"    
"Low Cruise Control Speed Set Limit"    
24 to 204 km/h (15 to 127 mph)    
204 km/h (127 mph)    
"High Cruise Control Speed Set Limit"    
32 to 204 km/h (20 to 127 mph)    
204 km/h (127 mph)    
"Exhaust Brake Mode"     "Coast"
"Latch"
"Manual"     "Manual"    
"Auto Retarder in Cruise (0 = Off)"    
0 to 16 km/h (0 to 10 mph)    
0 km/h (0 mph)    
"Auto Retarder in Cruise Increment"    
0 to 8 km/h (0 to 5 mph)    
0 km/h (0 mph)    
"Cruise/Idle/PTO Switch Configuration"     "Set/Decel - Res/Accel"
"Set/Accel - Res/Decel"     "Set/Accel - Res/Decel"    
"Soft Cruise Control"     "Yes"
"No"     "Yes"    
"Idle Parameters"    
"Idle Vehicle Speed Limit"    
2 to 24 km/h (1 to 15 mph)    
2 km/h (1 mph)    
"Idle RPM Limit"     700 to TEL rpm     TEL rpm    
"Idle/PTO RPM Ramp Rate"     5 to 1000 rpm/sec     50 rpm/sec    
"Idle/PTO Bump RPM"     5 to 500 rpm     20 rpm    
"Fast Idle RPM #1"     700 to TEL rpm     1000 rpm    
"Fast Idle RPM #2"     700 to TEL rpm     0 rpm    
"Warm up Mode Idle Speed"     700 to 1400 rpm     1000 rpm    
"Dedicated PTO Parameters"    
"PTO Configuration"     "Off"
"Cab Switches"
"Remote Switches"
"Remote Throttle"     "Off"    
"PTO Top Engine Limit"     700 to TEL rpm     TEL rpm    
"PTO Engine RPM Set Speed (0 = Off)"     Low Idle to PTO TEL rpm     0 rpm    
"PTO Engine RPM Set Speed A"     Low Idle to PTO TEL rpm     0 rpm    
"PTO Engine RPM Set Speed B"     Low Idle to PTO TEL rpm     0 rpm    
"PTO to Set Speed"     "Yes"
"No"     "No"    
"Maximum PTO