3109545 KIT-GASKET Caterpillar parts
320D, 320D FM, 320D GC, 320D L
Rating:
Alternative (cross code) number:
CA3109545
310-9545
3109545
CA3109545
310-9545
3109545
Weight: 3 pounds 1 kg.
EXCAVATOR,
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
$289.51
19 Mar 2018
452 Hundredths Pounds
CTP: CTP
Caterpillar KIT-GASKET (3109545)
3109545 Caterpillar Weight(lbs): 4.50 Length(cm): 95.6000 Width(cm): 34.6000 Depth(cm): 5.7000
3109545 Caterpillar Weight(lbs): 4.50 Length(cm): 95.6000 Width(cm): 34.6000 Depth(cm): 5.7000
For full view, you need register
Information:
Remove And Install Fuel Injection Nozzles And Adapters
This procedure is for later 7000 Series Fuel Injection Nozzles with 40.45 mm (1.593 in.) adapter bores.START BY:a. remove valve covers
Typical Example1. Use tool (A), and disconnect fuel line (1) at both ends. Remove the fuel line from the engine.2. Use tool (B), and remove retainer (2) from the adapter.3. Remove the fuel injection nozzles with tooling (C) as follows:a. Install the 6V6983 Adapter and the 8T3199 Screw into nozzle assembly (3).b. The 8T3198 Tube over the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw to pull the fuel injection nozzle from the adapter.4. Remove compression seal (4) and carbon dam seal (8) from fuel injection nozzle (3).5. Use tool (D), and remove adapter (6) from the cylinder head.6. Remove gasket (7) and seal (5) from adapter (6). The following steps are for installation of the fuel injection nozzles and adapters.7. Use tool (E) to clean the bore in adapter (6). Use an open end wrench or tap driver to turn tool (E).8. Inspect seal (5) for damage or wear. Replace the seal if necessary.9. Put washer (7) and seal (5) in position on adapter (6).10. Put liquid soap in the bores of the cylinder head and in seals (5) in the adapters.11. Put 5P3931 Anti-Seize Compound on the threads of adapter (6), and install the adapter in the cylinder head assembly.12. Use tool (D), and tighten the adapter to a torque of 205 14 N m (150 10 lb.ft.).
Make sure the correct compression seal washer (4) is used when the nozzle assembly is installed in the adapter. Only copper washers are to be used with this adapter.
13. Install compression seal washer (4), and use tool (F) to install carbon dam seal (8) on the fuel injection nozzle.14. Put fuel injection nozzle (3) in position in the adapter, and install retainer (2).15. Use tool (B) to tighten retainer (2) to a torque of 48 7 N m (35 5 lb.ft.).16. Install fuel line (1). Tighten the nuts on the fuel line with tool (A) to a torque of 40 7 N m (30 5 lb.ft.).END BY:a. install valve covers
This procedure is for later 7000 Series Fuel Injection Nozzles with 40.45 mm (1.593 in.) adapter bores.START BY:a. remove valve covers
Typical Example1. Use tool (A), and disconnect fuel line (1) at both ends. Remove the fuel line from the engine.2. Use tool (B), and remove retainer (2) from the adapter.3. Remove the fuel injection nozzles with tooling (C) as follows:a. Install the 6V6983 Adapter and the 8T3199 Screw into nozzle assembly (3).b. The 8T3198 Tube over the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw to pull the fuel injection nozzle from the adapter.4. Remove compression seal (4) and carbon dam seal (8) from fuel injection nozzle (3).5. Use tool (D), and remove adapter (6) from the cylinder head.6. Remove gasket (7) and seal (5) from adapter (6). The following steps are for installation of the fuel injection nozzles and adapters.7. Use tool (E) to clean the bore in adapter (6). Use an open end wrench or tap driver to turn tool (E).8. Inspect seal (5) for damage or wear. Replace the seal if necessary.9. Put washer (7) and seal (5) in position on adapter (6).10. Put liquid soap in the bores of the cylinder head and in seals (5) in the adapters.11. Put 5P3931 Anti-Seize Compound on the threads of adapter (6), and install the adapter in the cylinder head assembly.12. Use tool (D), and tighten the adapter to a torque of 205 14 N m (150 10 lb.ft.).
Make sure the correct compression seal washer (4) is used when the nozzle assembly is installed in the adapter. Only copper washers are to be used with this adapter.
13. Install compression seal washer (4), and use tool (F) to install carbon dam seal (8) on the fuel injection nozzle.14. Put fuel injection nozzle (3) in position in the adapter, and install retainer (2).15. Use tool (B) to tighten retainer (2) to a torque of 48 7 N m (35 5 lb.ft.).16. Install fuel line (1). Tighten the nuts on the fuel line with tool (A) to a torque of 40 7 N m (30 5 lb.ft.).END BY:a. install valve covers
Caterpillar SIS machinery equipment:
Caterpillar SIS
320D & 320D L Excavators MCH00001-UP (MACHINE) POWERED BY C6.4 Engine »
310-9545
KIT-GASKET
320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED BY C6.4 Engine »
310-9545
KIT-GASKET
320D & 320D L Excavators JFZ00001-UP (MACHINE) POWERED BY C6.4 Engine »
310-9545
KIT-GASKET
320D Excavator BZP00001-UP (MACHINE) POWERED BY C6.4 Engine »
310-9545
KIT-GASKET
320D L Excavator SPN00001-UP (MACHINE) POWERED BY C6.4 Engine »
310-9545
KIT-GASKET
320D GC Excavator PCM00001-UP (MACHINE) POWERED BY C6.4 Engine »
310-9545
KIT-GASKET
320D Excavator KHN00001-UP (MACHINE) POWERED BY C6.4 Engine »
310-9545
KIT-GASKET
320D Excavator JPD00001-UP (MACHINE) POWERED BY C6.4 Engine »
310-9545
KIT-GASKET
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 323D L, 323D LN, 323D SA, 324D, 324D L
320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 323D L, 323D2 L, 324D, 324D L
320D, 320D FM, 320D FM RR, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E L, 323D L, 323D2 L, 324D, 324D L, 324E, 324E L, 324E LN, 326D L
320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D L, 326D ...
320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 323D L, 323D LN, 323D SA
320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 323D L, 323D2 L
320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 323D L, 323D2 L
320D, 320D FM, 320D L, 323D L, 323D LN, 323D SA, 325D, 325D L, 328D LCR, 329D, 329D L
320D, 320D L, 323D L, 323D LN, 323D SA, 325D, 325D L, 328D LCR, 329D, 329D L
320D, 320D L, 323D L, 325D L, 329D, 329D L
320D, 320D L, 320E L, 325D, 325D L, 328D LCR, 329D, 329D L
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
3906985
KIT-OIL COOLER & LINES GASKET
621F, 621G, 623G, 627G
621F, 621G, 623G, 627G
2Q2953
KIT GROUP-PCS
938F, 980G
938F, 980G
8N6274
KIT-CYLINDER BLOCK HARDWARE
120G, 130G, 3304, 518, 920, 930, 941, 950, 951B, 955L, D4E
120G, 130G, 3304, 518, 920, 930, 941, 950, 951B, 955L, D4E
3N8951
KIT-MARINE SPARE PARTS
3406, 3406B, 3408, D342, D342C, D343
3406, 3406B, 3408, D342, D342C, D343
3654083
KIT-INSTALLATION
Caterpillar
Caterpillar
1G9729
KIT-DRUM
CP-563, CS-583
CP-563, CS-583