3261008 KIT-FUEL TRANSFER PUMP Caterpillar parts
140M, 160M
Rating:
Alternative (cross code) number:
CA3261008
326-1008
3261008
CA3261008
326-1008
3261008
Weight: 4 pounds 1 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Information:
Introduction
This Special Instruction contains the necessary instructions in order to install the following Jacket Water Heaters: 3T-8724, 6N-9125, 7E-5244, 7E-6310, 9X-3294, 9Y-5316, 9Y-5318, 127-8603, 127-8605, 166-0658 and 194-7258.
You must read all of the instructions and you must fully understand all of the instructions within this article before you attempt any part of the procedure.
Installation Instructions for Seal Kit
The following procedure is recommended for installation of the following Seal Kits: 132-1448, 133-3413 and 161-8200. Refer to Table 1.
Table 1
Core Plug Bore Diameter     Seal Kit    
Ø 31.8     133-3413    
Ø 38.1     161-8200    
Ø 44.0     132-1448    
Illustration 1 g00804700
Typical Installation Of Seal Kit (1) Snap Ring. (2) Retainer Rings. (3) Spacer Ring. (4) Seal. (5) Heater Adapter. (6) Cap Assembly. (7) Cord Assembly.
If necessary, remove old snap ring (1), retainer rings (2), spacer ring (3), and seal (4). Discard old parts.
Clean heater adapter (5). Make sure that the heater adapter is free from dirt, grease, and any other debris.
Install seal (4) onto heater adapter (5) .
Install retainer rings (2) and spacer ring (3) .Note: Assemble retainer rings (2) on each side of spacer ring (3). Offset the teeth from each other and orient the teeth toward seal (4). Refer to Illustration 1.
Install snap ring (1) .Installation Instructions for Jacket Water Heaters
The following procedure is recommended for installation of the Jacket Water Heaters.
Illustration 2 g00803515
Typical Installation Of Jacket Water Heaters
Allow the engine to cool and drain the coolant.
Remove the existing jacket water heater. If new installation is required, remove the appropriate cup plug from the bore in the block.
Clean the bore in the block until the bore is free of any deposits.Note: If the outside edge of the bore is not chamfered, file any sharp edges.
Remove cap assembly (6) from the heater.
Apply a light coat of grease to seal (4) and to the bore.
Place the heater SQUARELY into the bore. Ensure that the heater element is oriented correctly.Note: Do not wedge the heater into the bore because damage to the retaining rings and the seal may result. The heater element should not touch any walls.
Once the heater has started into the bore, place a 1 1/4 inch deep socket over the threaded end of the heater. Insert the heater by lightly tapping the socket until the heater adapter seals against the block.
Install cap assembly (6) onto the heater.Note: The cap assembly is used to protect the terminals when the cord assembly is disconnected from the heater.
Fill the engine with coolant. Start the engine and check the engine for leaks. Continue to operate the engine until the operating temperature is reached in order to ensure that all of the air is purged from the cooling system.
When the operating temperature is reached, stop the engine. Allow the engine to cool.
Check the coolant level in the radiator or in the expansion tank. If necessary, top off the coolant.
Remove cap assembly (6) from the heater.
Install cord assembly (7). Hand tighten the final installation of the cord assembly. Energize the heater.Note:
This Special Instruction contains the necessary instructions in order to install the following Jacket Water Heaters: 3T-8724, 6N-9125, 7E-5244, 7E-6310, 9X-3294, 9Y-5316, 9Y-5318, 127-8603, 127-8605, 166-0658 and 194-7258.
You must read all of the instructions and you must fully understand all of the instructions within this article before you attempt any part of the procedure.
Installation Instructions for Seal Kit
The following procedure is recommended for installation of the following Seal Kits: 132-1448, 133-3413 and 161-8200. Refer to Table 1.
Table 1
Core Plug Bore Diameter     Seal Kit    
Ø 31.8     133-3413    
Ø 38.1     161-8200    
Ø 44.0     132-1448    
Illustration 1 g00804700
Typical Installation Of Seal Kit (1) Snap Ring. (2) Retainer Rings. (3) Spacer Ring. (4) Seal. (5) Heater Adapter. (6) Cap Assembly. (7) Cord Assembly.
If necessary, remove old snap ring (1), retainer rings (2), spacer ring (3), and seal (4). Discard old parts.
Clean heater adapter (5). Make sure that the heater adapter is free from dirt, grease, and any other debris.
Install seal (4) onto heater adapter (5) .
Install retainer rings (2) and spacer ring (3) .Note: Assemble retainer rings (2) on each side of spacer ring (3). Offset the teeth from each other and orient the teeth toward seal (4). Refer to Illustration 1.
Install snap ring (1) .Installation Instructions for Jacket Water Heaters
The following procedure is recommended for installation of the Jacket Water Heaters.
Illustration 2 g00803515
Typical Installation Of Jacket Water Heaters
Allow the engine to cool and drain the coolant.
Remove the existing jacket water heater. If new installation is required, remove the appropriate cup plug from the bore in the block.
Clean the bore in the block until the bore is free of any deposits.Note: If the outside edge of the bore is not chamfered, file any sharp edges.
Remove cap assembly (6) from the heater.
Apply a light coat of grease to seal (4) and to the bore.
Place the heater SQUARELY into the bore. Ensure that the heater element is oriented correctly.Note: Do not wedge the heater into the bore because damage to the retaining rings and the seal may result. The heater element should not touch any walls.
Once the heater has started into the bore, place a 1 1/4 inch deep socket over the threaded end of the heater. Insert the heater by lightly tapping the socket until the heater adapter seals against the block.
Install cap assembly (6) onto the heater.Note: The cap assembly is used to protect the terminals when the cord assembly is disconnected from the heater.
Fill the engine with coolant. Start the engine and check the engine for leaks. Continue to operate the engine until the operating temperature is reached in order to ensure that all of the air is purged from the cooling system.
When the operating temperature is reached, stop the engine. Allow the engine to cool.
Check the coolant level in the radiator or in the expansion tank. If necessary, top off the coolant.
Remove cap assembly (6) from the heater.
Install cord assembly (7). Hand tighten the final installation of the cord assembly. Energize the heater.Note:
Caterpillar SIS machinery equipment:
Caterpillar SIS
160M Motor Grader B9L00001-UP (MACHINE) POWERED BY C9 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
140M Motor Grader B9M00001-UP (MACHINE) »
326-1008
KIT-FUEL TRANSFER PUMP
160M Motor Grader B9E00001-UP (MACHINE) POWERED BY C9 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
140M Motor Grader B9D00001-UP (MACHINE) »
326-1008
KIT-FUEL TRANSFER PUMP
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY C9 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
140M Motor Grader - All Wheel Drive D9G00001-UP (MACHINE) POWERED BY C9 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
160M Motor Grader - All Wheel Drive B9T00001-UP (MACHINE) POWERED BY C9 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
160M Motor Grader - All Wheel Drive D9T00001-UP (MACHINE) POWERED BY C9 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
140M Series 2 Motor Grader M9D00001-UP (MACHINE) POWERED BY C9.3 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
140M Series 2 Motor Grader - All Wheel Drive M9J00001-UP (MACHINE) POWERED BY C9.3 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
160M Series 2 Motor Grader - All Wheel Drive M9K00001-UP (MACHINE) POWERED BY C9.3 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
160M Series 2 Motor Grader M9E00001-UP (MACHINE) POWERED BY C9 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
14L Motor Grader - All Wheel Drive B9400001-UP (MACHINE) POWERED BY C9 Engine »
326-1008
KIT-FUEL TRANSFER PUMP
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
9M0402
KIT-GOVERNOR OVERHAUL
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 16...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 16...
8Y6860
KIT-SPRING
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
1003408
KIT-BIAS PISTON
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
1003415
KIT-CONTROL PISTON
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
1143616
KIT-SEAL
1090, 1190, 1190T, 1290T, 12M 2, 1390, 140M, 160M, 2290, 2390, 2391, 2491, 2590, 320B FM LL, 320C FM, 320D, 320D FM, 320D FM RR, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 325B L, 325C FM, 325D FM, 3...
1090, 1190, 1190T, 1290T, 12M 2, 1390, 140M, 160M, 2290, 2390, 2391, 2491, 2590, 320B FM LL, 320C FM, 320D, 320D FM, 320D FM RR, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 325B L, 325C FM, 325D FM, 3...
2006282
KIT-SEAL
120M, 12M, 140M, 14M, 160M, 16M, 24M, 583T, 587R, 587T, 725, 730, 797, 797B, 928H, 938H, 950H, 962H, 966H, 972H, 994F, CB-44B, CB-54B, D10T, D11T, IT28G, IT38H, IT62H
120M, 12M, 140M, 14M, 160M, 16M, 24M, 583T, 587R, 587T, 725, 730, 797, 797B, 928H, 938H, 950H, 962H, 966H, 972H, 994F, CB-44B, CB-54B, D10T, D11T, IT28G, IT38H, IT62H
2402016
KIT-SEAL
140M, 160M, 518C, 627E, 637E, 657E, SNOW WING
140M, 160M, 518C, 627E, 637E, 657E, SNOW WING
2339204
KIT-SEAL
120G, 120H, 120H ES, 120H NA, 120K, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 140M 3, 140M 3 AWD...
120G, 120H, 120H ES, 120H NA, 120K, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 140M 3, 140M 3 AWD...
1177799
KIT-SEAL
120M, 12M, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 24H, 24M, 525B, 525C, 535B, 535C, 545, 545C, 814F, 814F II, 815F, 815F II, 816F, 816F II, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 8...
120M, 12M, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 24H, 24M, 525B, 525C, 535B, 535C, 545, 545C, 814F, 814F II, 815F, 815F II, 816F, 816F II, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 8...
3260503
KIT-SEAL
120K, 120M, 12K, 12M, 12M 3, 12M 3 AWD, 140K, 140M, 140M 3, 140M 3 AWD, 160M, 160M 3, 160M 3 AWD, 950H, 950K, 962H, 962K, IT62H
120K, 120M, 12K, 12M, 12M 3, 12M 3 AWD, 140K, 140M, 140M 3, 140M 3 AWD, 160M, 160M 3, 160M 3 AWD, 950H, 950K, 962H, 962K, IT62H
9T9072
KIT-SEAL
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
1857688
KIT-SEAL
120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 24H, 24M
120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 24H, 24M
2643565
KIT-GASKET
120K, 120K 2, 3116, 3126, 3126B, 3126E, 324D L, 324D LN, 325C, 325D, 325D L, C7, M325D L MH
120K, 120K 2, 3116, 3126, 3126B, 3126E, 324D L, 324D LN, 325C, 325D, 325D L, C7, M325D L MH
3535450
KIT-CAMERA
834G, 834H, 844H, 854G, 988F, 988F II, 988G, 988H, 990H, 990K, 994F
834G, 834H, 844H, 854G, 988F, 988F II, 988G, 988H, 990H, 990K, 994F
5Y2230
KIT-CONVERSION-TRACK LINK
D4E, D4E SR
D4E, D4E SR
2575229
KIT-MOUNTING
BU115, BU118
BU115, BU118
4502547
KIT-GASKET
D6T LGP, D6T XL
D6T LGP, D6T XL
2624971
KIT-GASKET
3116, 3126E
3116, 3126E
3399352
KIT-CAP
793F, 793F AC, 793F OEM, 795F AC, 797F, C175-16, C175-20
793F, 793F AC, 793F OEM, 795F AC, 797F, C175-16, C175-20
3E3310
KIT-GASKET
3406B, 980F, 980F II
3406B, 980F, 980F II
4204427
KIT-GASKET
3412, 3412E
3412, 3412E
3860854
KIT-SERVICE
302.7D
302.7D