KIT-SEAL 3476233 - Caterpillar

3476233 KIT-SEAL Caterpillar parts 924H, 930K

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA3476233
347-6233
3476233

Weight: 0.04 pounds 0 kg.

Buy KIT-SEAL 3476233 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Hydraulic Cylinder Seal Kit 180-9872 295-9893 347-6233 Compatible with Caterpillar Machinery Parts (347-6233)

$52.52

12 Oct 2025

CN: guangzhouguoshu

Hydraulic Cylinder Seal Kit 180-9872 295-9893 347-6233 Compatible with Caterpillar Machinery Parts (347-6233)
Generic Hydraulic Cylinder Seal Kit 180-9872 295-9893 347-6233 Compatible with Caterpillar Machinery Parts

Hydraulic Cylinder Seal Kit, Compatible with 442D 430D 442E 434E 450E 450F 430E, 2959893 3476233, Machinery Replacement Part (2959893)

$36.13

11 Oct 2025

CN: guangzhouyixin0

Hydraulic Cylinder Seal Kit, Compatible with 442D 430D 442E 434E 450E 450F 430E, 2959893 3476233, Machinery Replacement Part (2959893)
Generic Hydraulic Cylinder Seal Kit, Compatible with 442D 430D 442E 434E 450E 450F 430E, 2959893 3476233, Machinery Replacement Part

Hydraulic Cylinder Seal Kit 180-9872 295-9893 347-6233 Compatible with Caterpillar Machinery Parts (295-9893)

$52.52

28 Aug 2025

HK: SHANDIEN

Hydraulic Cylinder Seal Kit 180-9872 295-9893 347-6233 Compatible with Caterpillar Machinery Parts (295-9893)
Generic Hydraulic Cylinder Seal Kit 180-9872 295-9893 347-6233 Compatible with Caterpillar Machinery Parts || Origin:Mainland China

Number on catalog scheme:

Caterpillar 3476233 Parts scheme KIT-SEAL

For full view, you need register

Compatible equipment models: 3476233:

WHEEL LOADER 924H 930K Caterpillar

Information:

Illustration 1 g00510788
General diagram for installation of the ether starting aid (1) Ether cylinder assemblyThe ether cylinder assembly should be installed within angle (A). (A) Dimension from the vertical centerline ... 20 degrees (2) Clamp assembly The clamp should be located above the mounting holes. ... 178 mm (7.0 inch) (3) Ether valve assembly Holding starting aid switch (5) down for three seconds will cause the ether valve assembly to deliver the following volume of ether to the atomizer. ... 2.25 cc (.137 cubic inch)Note: The ether valve assembly should be mounted as close as possible to the engine inlet manifold. The ether valve assembly should not be mounted on the engine. The ether valve assembly should not be exposed to temperatures higher than the following temperature of 93.3 °C (200.00 °F). Install the ether valve assembly so the cylinder assembly (1) can be installed in a vertical position. See illustration 1. (4) Temperature switchRemove the pipe plug from the cylinder head. Install the temperature switch in the cylinder head. See illustration 2.Note: The temperature switch will not allow the starting fluid to reach the atomizer if the engine temperature is above 38 3 °C (100.4 5.4 °F).
Illustration 2 g00502103
(5) Starting aid switchInstall the switch close to the operator's starting station. The switch requires adequate clearance for wiring behind the switch. (6) Ether valve connector (7) Steel tube Outer diameter of tubing ... 3.18 mm (.125 inch)Assemble the steel tubing between the valve assembly and the atomizer assembly. Use the flexible coupling tube assembly as a flexible connection between the two lines. The use of any additional length of tubing is not recommended. No electric wires should be clamped to the ether lines. (8) Atomizer assemblyRemove the pipe plug from the air inlet system and install the atomizer assembly. Before the atomizer assembly is tightened, align the identification mark. The mark should face the front or the rear of the engine. See illustration 2 and illustration 3.
Illustration 3 g00502001