3483289 KIT-GASKET(CL) Caterpillar parts
Rating:
Alternative (cross code) number:
CA3483289
348-3289
3483289
CA3483289
348-3289
3483289
Weight: 0.21 pounds 0 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$116.00
28 Aug 2021
5.0[2.25] Pounds
US: Highway And Hea
3483289 | Gasket Set - Central & Lower
HHP HIGHWAY & HEAVY PARTS HHP provides parts equal or better in quality compared to the OE at a fraction of the cost. || Products are crafted with hard-wearing materials for long-lasting strength and durability. || Parts meet or exceed OEM specifications to ensure proper fit and function. || Image(s) is for illustration purposes only and may not represent the actual part. || Products are only sourced from quality certified manufacturing facilities.
HHP HIGHWAY & HEAVY PARTS HHP provides parts equal or better in quality compared to the OE at a fraction of the cost. || Products are crafted with hard-wearing materials for long-lasting strength and durability. || Parts meet or exceed OEM specifications to ensure proper fit and function. || Image(s) is for illustration purposes only and may not represent the actual part. || Products are only sourced from quality certified manufacturing facilities.
For full view, you need register
Information:
the 2461 diagnostic codes.
Remove the jumper wire.Results:
A 2461-5 diagnostic code was active before installing the jumper. A 2461-6 diagnostic code is active when the jumper is installed - The fault is in the CEM harness.Repair: Repair the faulty wiring or replace the faulty wiring.Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.STOP
A 2461-5 diagnostic code is still active with the jumper installed. - Reconnect the 40-pin connector. Proceed to Test Step 5.Test Step 5. Create a Short Circuit at the 31-Pin Connector
Turn the keyswitch to the OFF position.
Disconnect the 31-pin connector.
Fabricate a jumper wire that is 150 mm (6 inch) long.
Install the wire between pin 21 and pin 22 on the 31-pin connector on the harness between the engine and the CEM.
Turn the keyswitch to the ON position. Wait for 10 seconds. Check for active diagnostic codes on the electronic service tool.Note: While the 31-pin connector is disconnected, diagnostic codes for the other components
Remove the jumper wire.Results:
A 2461-5 diagnostic code was active before installing the jumper. A 2461-6 diagnostic code is active when the jumper is installed - The fault is in the CEM harness.Repair: Repair the faulty wiring or replace the faulty wiring.Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.STOP
A 2461-5 diagnostic code is still active with the jumper installed. - Reconnect the 40-pin connector. Proceed to Test Step 5.Test Step 5. Create a Short Circuit at the 31-Pin Connector
Turn the keyswitch to the OFF position.
Disconnect the 31-pin connector.
Fabricate a jumper wire that is 150 mm (6 inch) long.
Install the wire between pin 21 and pin 22 on the 31-pin connector on the harness between the engine and the CEM.
Turn the keyswitch to the ON position. Wait for 10 seconds. Check for active diagnostic codes on the electronic service tool.Note: While the 31-pin connector is disconnected, diagnostic codes for the other components
Parts kit Caterpillar catalog:
3481638
KIT-BOOM GP
Caterpillar
Caterpillar
3480802
KIT-LOADCHART
Caterpillar
Caterpillar
3479324
KIT GP-CVRSN
Caterpillar
Caterpillar
3479300
KIT-WIRING GP
Caterpillar
Caterpillar
3479299
KIT-WIRING GP
Caterpillar
Caterpillar
3479298
KIT-WIRING GP
Caterpillar
Caterpillar
3483297
KIT-GASKET(T)
Caterpillar
Caterpillar
Caterpillar
3483294
KIT-
Caterpillar
Caterpillar
3483293
KIT-GASKET(RS)
Caterpillar
Caterpillar
Caterpillar
3483290
KIT-GASKET(F)
Caterpillar
Caterpillar