AVSPARE.COM
parts catalog

KIT-WATER PUMP GASKET 3904622 - Caterpillar



3904622 KIT-WATER PUMP GASKET Caterpillar parts 824G II, 825G II, 826G II KIT
Rating:
66
Alternative (cross code) number:
CA3904622
390-4622
3904622
Caterpillar 3904622 KIT-WATER PUMP GASKET
Weight: 0.11 pounds 0 kg.

Buy KIT-WATER PUMP GASKET 3904622 Caterpillar genuine, new aftermarket tractor parts with delivery
LANDFILL COMPACTOR, WHEEL DOZER,

Compatible equipment models: 3904622:

LANDFILL COMPACTOR  826G II  
SOIL COMPACTOR  825G II  
WHEEL DOZER  824G II   Caterpillar
  For full view, you need register

Information:


Illustration 1 g03327368
Schematic of the "3rd Function Rear Attachment Solenoid 6"
The cid 2216 diagnostic code is associated with the 3rd function rear attachment solenoid. The FMI 06 diagnostic code means that the Implement ECM reads the current of the solenoid as being above normal.The possible causes are listed below:
A wire is shorted to ground.
The solenoid has failed.
The ECM has failed. This condition is unlikely.System Response:
A level 2 warning will be generated.
All functions of "Aux 3 Solennoid B" are lost.
The "Auto Stow" feature will be disabled.Note: Ensure that the CID 2216 FMI 06 diagnostic code for the solenoid is active. Note: The following procedure can create numerous related diagnostic codes. When all harnesses are reconnected, the related diagnostic codes will be shown as being not active. Clear all related diagnostic codes after this procedure is completed.Test Step 1. CHECK THE SOLENOID
Turn the disconnect switch and the key start switch to the ON position. DO NOT start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:The active CID 2216 FMI 06 diagnostic code changes to a CID 2216 FMI 05 diagnostic code.Results:
OK - The active CID 2216 FMI 06 diagnostic code changes to a CID 2216 FMI 05 diagnostic code. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" to verify the solenoid failure. Replace the solenoid. Calibrate the solenoid for the "bladelower" function. Refer to Testing and Adjusting, "Calibration" procedure in the service manual for your machine.STOP
NOT OK - The CID 2216 FMI 06 diagnostic code remains active. The solenoid is not causing the problem. Proceed to test step 2.Test Step 2. CHECK THE SOLENOID CIRCUIT FOR A SHORT TO GROUND.
The machine harness remains disconnected from the solenoid.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1 and J2 machine harness connector from the ECM.
At the J2 machine harness connector, measure the resistance from the solenoid contact J1-66 (wire J940-GY(Grey)) to all possible sources of ground. Expected Result:Each resistance measurement should be greater than 5000 ohms.Results:
YES - Each measurement is greater than 5000 ohms. The machine harness is correct. Proceed to test step 3.
NO - One or more measurements is not correct. There is a short in the machine harness.Repair: The short is between the wire for the solenoid signal and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK THE STATUS OF THE DIAGNOSTIC CODE
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Stop the machine and place the parking brake switch in the ON position.
Check if the CID 2216 FMI 06 diagnostic code is active. Expected Result:The CID 2216 FMI 06 diagnostic code is NO longer active. Results:
OK - The CID 2216 FMI 06 diagnostic code is no longer active. The diagnostic code does

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts kit Caterpillar catalog:

3777037 KIT-WATER PUMP
16G, 16H NA, 24H, 24M, 3126, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 3516, 375, 375 L, 385B, 5080, 5090B, 5110B, 578, 583R, 583T, 587R, 587T, 589, 621B, ...
3491530 KIT-GASKET
3406E, 621F, 621G, 621H, 623E, 623F, 623G, 623H, 627F, 627G, 627H, 657E, 824G II, 824H, 825G II, 825H, 826G II, 826H, 980H
2436718 KIT-CRANKSHAFT BEARING
16G, 16H NA, 24H, 24M, 3406, 3406B, 3406C, 3406E, 3412, 3412C, 3412D, 3412E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5...
7T3451 KIT-INSULATOR
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 16...
7T3267 KIT-BUSHING
120G, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673C, 16G, 16H, 16H NA, 16M, 215B,...
7T3268 KIT-LEVER
120G, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673C, 16G, 16H, 16H NA, 16M, 215B,...
8T9884 KIT-INSULATOR
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 16...
8C3655 KIT-BRUSH
120G, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673C, 16G, 16H, 16H NA, 16M, 215B,...
3G8175 KIT-SEAL
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA,...
1977701 KIT-SEAL
1090, 1190, 1190T, 1290T, 12G, 1390, 140G, 322B L, 325B, 345B II, 350, 3508B, 3512, 3512B, 3512C, 3516B, 3516C, 375, 426C, 436C, 438C, 438D, 442D, 511, 515, 521, 522, 525, 525B, 532, 539, 541, 550, 55...
1129861 KIT-SEAL
216, 216B3, 226B3, 236, 236B3, 242B3, 247B3, 252B3, 257B3, 259B3, 267B, 301.5, 301.6C, 302.5, 302.5C, 631G, 637G, 657E, 814F, 814F II, 815F II, 816F II, 824G II, 824H, 834G, 854G, 906H, 906H2, 907H, 9...
1082148 KIT-SEAL
120M, 120M 2, 12M, 12M 2, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 24M, 568 FM LL, 824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 924K, 930K, 938F, 938G, 938G II, 938H, 938K, 950G, 950G I...
4184757 KIT-OIL SYSTEM GASKET
140H, 143H, 14H, 160H, 163H, 966G II
4162498 KIT-TURBOCHARGER GASKET
140H, 143H, 14H, 160H, 163H
4237969 KIT-GASKET
824G II, 825G II, 826G II
4237970 KIT-TURBOCHARGER GASKET
824G II, 825G II, 826G II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.