3933611 KIT-HYD CYLINDER SEAL Caterpillar parts
D6T
Rating:
Alternative (cross code) number:
CA3933611
393-3611
3933611
CA3933611
393-3611
3933611
Weight: 0.20 pounds 0 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 3933611:
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove all of the plastic plugs from all of the ports of the turbocharger (1). Clean the mating surfaces of the exhaust manifold and the turbocharger. Clean the mating surfaces of the turbocharger to the oil supply tube assembly (6) and the turbocharger to the oil drain tube assembly (9).
Ensure that all of the turbocharger inlet and outlet ports are clean and free from restrictions. The turbocharger shaft must rotate freely.
Illustration 1 g01038396
Typical example
If the studs (15) were previously removed, install the studs into the exhaust manifold. Install a new gasket (14) over the studs (15). Note: Do not use any sealant on the gasket (14).Note: Do not use the actuator rod of the wastegate (16) to lift the turbocharger (1).
Position the turbocharger (1) onto the exhaust manifold.
Install the nuts (13). Tighten the nuts (13) to a torque of 47 N m (35 lb ft).
Lubricate the bearing housing of the turbocharger (1) with clean engine oil.
Inspect all of the oil hose assemblies (6 and 9). If necessary, replace the hose assemblies (6 and 9). Note: The top flange of the oil drain tube assembly (9) is secured to the turbocharger (1) with 6 mm setscrews (8). The bottom flange of the oil drain tube assembly (9) is secured to the cylinder block with 8 mm setscrews (11).
Position a new joint (10) and the oil drain tube assembly (9) onto the bottom of the turbocharger (1). Install the 6 mm setscrews (8). Tighten the 6 mm setscrews (8) to a torque of 9 N m (80 lb in).
Position a new joint and the oil drain tube assembly (9) onto the cylinder block. Tighten the 8 mm setscrews (11) to a torque of 22 N m (16 lb ft).
Position the new washers (7) and the oil supply tube assembly (6) onto the turbocharger (1). Install the banjo bolt (5). Tighten the banjo bolt (5) to a torque of 22 N m (16 lb ft). Note: Ensure that the oil supply tube assembly (6) does not come into contact with any other component when the assembly is installed onto the engine.
Install the new washers and the oil supply tube assembly (6) to the cylinder block. Tighten the banjo bolt to a torque of 22 N m (16 lb ft).
If the studs (12) were previously removed, install the studs into the turbocharger housing.
Illustration 2 g01038406
Typical example
Position the exhaust adapter (3) onto the studs (12). Install the nuts (2). Do not tighten the nuts (2) at this time. Note: Exhaust elbows are only an option for the four cylinder engines.
If equipped, install the exhaust elbow onto the exhaust adapter (3). Refer to this Disassembly and Assembly Manual, "Exhaust Elbow - Remove and Install".
Illustration 3 g01038456
Tighten the three nuts finger tight in the sequence (17), (18), and (19). Tighten the nuts (17), (18), and (19) in the same sequence to a torque of 25 N m (18 lb ft).
Ensure that there is no
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove all of the plastic plugs from all of the ports of the turbocharger (1). Clean the mating surfaces of the exhaust manifold and the turbocharger. Clean the mating surfaces of the turbocharger to the oil supply tube assembly (6) and the turbocharger to the oil drain tube assembly (9).
Ensure that all of the turbocharger inlet and outlet ports are clean and free from restrictions. The turbocharger shaft must rotate freely.
Illustration 1 g01038396
Typical example
If the studs (15) were previously removed, install the studs into the exhaust manifold. Install a new gasket (14) over the studs (15). Note: Do not use any sealant on the gasket (14).Note: Do not use the actuator rod of the wastegate (16) to lift the turbocharger (1).
Position the turbocharger (1) onto the exhaust manifold.
Install the nuts (13). Tighten the nuts (13) to a torque of 47 N m (35 lb ft).
Lubricate the bearing housing of the turbocharger (1) with clean engine oil.
Inspect all of the oil hose assemblies (6 and 9). If necessary, replace the hose assemblies (6 and 9). Note: The top flange of the oil drain tube assembly (9) is secured to the turbocharger (1) with 6 mm setscrews (8). The bottom flange of the oil drain tube assembly (9) is secured to the cylinder block with 8 mm setscrews (11).
Position a new joint (10) and the oil drain tube assembly (9) onto the bottom of the turbocharger (1). Install the 6 mm setscrews (8). Tighten the 6 mm setscrews (8) to a torque of 9 N m (80 lb in).
Position a new joint and the oil drain tube assembly (9) onto the cylinder block. Tighten the 8 mm setscrews (11) to a torque of 22 N m (16 lb ft).
Position the new washers (7) and the oil supply tube assembly (6) onto the turbocharger (1). Install the banjo bolt (5). Tighten the banjo bolt (5) to a torque of 22 N m (16 lb ft). Note: Ensure that the oil supply tube assembly (6) does not come into contact with any other component when the assembly is installed onto the engine.
Install the new washers and the oil supply tube assembly (6) to the cylinder block. Tighten the banjo bolt to a torque of 22 N m (16 lb ft).
If the studs (12) were previously removed, install the studs into the turbocharger housing.
Illustration 2 g01038406
Typical example
Position the exhaust adapter (3) onto the studs (12). Install the nuts (2). Do not tighten the nuts (2) at this time. Note: Exhaust elbows are only an option for the four cylinder engines.
If equipped, install the exhaust elbow onto the exhaust adapter (3). Refer to this Disassembly and Assembly Manual, "Exhaust Elbow - Remove and Install".
Illustration 3 g01038456
Tighten the three nuts finger tight in the sequence (17), (18), and (19). Tighten the nuts (17), (18), and (19) in the same sequence to a torque of 25 N m (18 lb ft).
Ensure that there is no
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
1552265
KIT-CONNECTING PLUG
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
1028806
KIT-RECEPTACLE
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
1028804
KIT-RECEPTACLE
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
1650699
KIT-MOUNTING BRACKET
16M, 24M, 3406C, 3412C, 3456, 572R II, 587T, 621F, 621G, 623F, 623G, 627F, 627G, 631E, 631G, 633E, 637E, 637G, 651E, 657E, 65E, 725, 730, 735, 740, 75C, 75E, 773F, 775F, 777F, 784B, 784C, 785B, 785C, ...
16M, 24M, 3406C, 3412C, 3456, 572R II, 587T, 621F, 621G, 623F, 623G, 627F, 627G, 631E, 631G, 633E, 637E, 637G, 651E, 657E, 65E, 725, 730, 735, 740, 75C, 75E, 773F, 775F, 777F, 784B, 784C, 785B, 785C, ...
1600496
KIT-SEAL
140M, 160M, 414E, 416C, 416D, 416E, 420D, 420E, 422E, 424D, 426C, 428C, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 436C, 438C, 438D, 442D, 442E, 444E, 446B, 446D, 450E, 450F, 515, 525, 525B, 533, 535B,...
140M, 160M, 414E, 416C, 416D, 416E, 420D, 420E, 422E, 424D, 426C, 428C, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 436C, 438C, 438D, 442D, 442E, 444E, 446B, 446D, 450E, 450F, 515, 525, 525B, 533, 535B,...
1335545
KIT-SEAL
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 24H, 24M, 336E H, 336E LH, 345B II, 525C, 535C, 545C, 583T, 584, 587R, 587T, 6...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 24H, 24M, 336E H, 336E LH, 345B II, 525C, 535C, 545C, 583T, 584, 587R, 587T, 6...
1265948
KIT-SEAL
1090, 1190, 1190T, 1290T, 1390, 216, 228, 236, 236B, 242B, 247, 247B, 248, 24H, 267, 267B, 268B, 287, 320D, 320D FM, 322B L, 324D FM, 324D FM LL, 325B L, 325C FM, 325D FM, 325D FM LL, 325D MH, 330, 33...
1090, 1190, 1190T, 1290T, 1390, 216, 228, 236, 236B, 242B, 247, 247B, 248, 24H, 267, 267B, 268B, 287, 320D, 320D FM, 322B L, 324D FM, 324D FM LL, 325B L, 325C FM, 325D FM, 325D FM LL, 325D MH, 330, 33...
3507735
KIT-CAP FILTER
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2390, 2391, 2470C, 2491, 24M, 257...
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2390, 2391, 2470C, 2491, 24M, 257...
1113203
KIT-SEAL
349E, 349E L, 349E L HVG, 349E L VG, 349F L, 3516B, 769D, 771D, 773D, 773F, 775D, 775F, 777F, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 973C, 973D, 994D, 994F, 994H, C-10, C-12, C-15...
349E, 349E L, 349E L HVG, 349E L VG, 349F L, 3516B, 769D, 771D, 773D, 773F, 775D, 775F, 777F, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 973C, 973D, 994D, 994F, 994H, C-10, C-12, C-15...
2292626
KIT-SEAL
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II
2160805
KIT-COIL
517, 527, 539, 816F, 816F II, 824H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 950H, 953C, 963C, 966H, 973C, 988G, 988H, D10N, D10R, D10T, D11R, D11T, D4H, D4HTSK III, D5HTSK II, D5M, D6M, D6R, D6R ...
517, 527, 539, 816F, 816F II, 824H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 950H, 953C, 963C, 966H, 973C, 988G, 988H, D10N, D10R, D10T, D11R, D11T, D4H, D4HTSK III, D5HTSK II, D5M, D6M, D6R, D6R ...
8Y6860
KIT-SPRING
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
3030454
KIT-SEAL
D3K XL, D3K2 LGP
D3K XL, D3K2 LGP
3030453
KIT-DISC
D3K XL, D3K2 LGP
D3K XL, D3K2 LGP
3566447
KIT-SEAL
D3K XL, D3K2 LGP, D4K XL, D4K2 XL, D5K LGP, D5K2 XL, D6K2, D6K2 LGP
D3K XL, D3K2 LGP, D4K XL, D4K2 XL, D5K LGP, D5K2 XL, D6K2, D6K2 LGP
3041151
KIT-COVER
D3K XL, D3K2 LGP, D4K XL, D4K2 XL, D5K LGP, D5K2 XL
D3K XL, D3K2 LGP, D4K XL, D4K2 XL, D5K LGP, D5K2 XL
3744547
KIT-SEAL
973D
973D
3639877
KIT-FAN BLADE
568 FM LL, 973D
568 FM LL, 973D
3275990
KIT-VALVE
PL61
PL61
3275989
KIT-VALVE
PL61
PL61
3275999
KIT-VALVE
PL61
PL61
3276000
KIT-VALVE
PL61
PL61