AVSPARE.COM
parts catalog

KIT-HYDRAULIC CYLINDER SEAL 4398573 - Caterpillar


4398573 KIT-HYDRAULIC CYLINDER SEAL Caterpillar parts 730, TH350B, TH355B
Rating:
47
Alternative (cross code) number:
CA4398573
439-8573
4398573
Caterpillar 4398573 KIT-HYDRAULIC CYLINDER SEAL
Weight: 0.19 pounds 0 kg.

Buy KIT-HYDRAULIC CYLINDER SEAL 4398573 Caterpillar genuine, new aftermarket tractor parts with delivery
EJECTOR TRUCK, TELEHANDLER,

Compatible equipment models: 4398573:

EJECTOR TRUCK  730  
TELEHANDLER  TH350B   TH355B   Caterpillar
Number on catalog scheme:
  For full view, you need register

Information:


Illustration 1. Location of "A" and "B" Pins.Procedure for "A" Pin:
Illustration 2. Section A-A (refer to Illustration 1). Make sure that collets, pins and all mating surfaces are clean before beginning procedure.1. When installing "A" pins, position the lift arms so that they are evenly spaced between the NEEF (Non-Engine End Frame) and the lift arm bores.2. Insert approximately the same number of 103-1814 Shims 3.0 mm (.12 in) (6) and/or 103-1815 Shims 5.0 mm (.20 in) (7) on both sides of the lift arm (see Illustration 2). This should evenly space the lift arm between the NEEF bores. This procedure is to determine the necessary number of shims. Do not FORCE shims into the space between the lift arm and NEEF bores.3. Remove the determined number of shims.4. Insert 8X-0660 Pin (3) through the NEEF and lift arm, with the determined number of shims in position. Apply 5P-0960 Molybdenum Grease or equivalent to the outside of the 8X-0660 Pin before installation. Measure the distance on both sides of the installed pin and position pin evenly on both sides.5. Install 8X-0663 Collets (2) on both sides of the lift arm. Apply 4C-5599 High Temperature Anti-Seize to the inside of the collet before assembly.6. Install a 3E-8011 Bolt (1) and 3S-7023 Washer (5) through 8X-0660 Pin. Apply 4C-5599 High Temperature Anti-Seize to the bolt threads before assembly.7. Install the 3S-7023 Washer (4) and the 8T-1583 Nut (8).8. Tighten the bolt to a torque of 1800 200 N m (1332 149 lb ft). Maintain the 8X-0663 Collets spacing as evenly as possible on both sides of the lift arm as this procedure is being followed.9. Use hammers to impact the collets on both sides to sufficiently cause the bolt torque to drop to less than 950 N m (700 lb ft).10. Tighten the bolt to a torque of 1800 200 N m (1332 149 lb ft).11. Use hammers to impact the collets on both sides again to sufficiently cause the bolt torque to drop to less than 1600 N m (1182 lb ft).12. Tighten the bolt to a torque of 1800 200 N m (1332 149 lb ft). Tighten the bolt to a torque of 1800 200 N m (1332 149 lb ft) after 50 hours of operation.13. Repeat this procedure for the other "A" Pin.Procedure for "B" Pin:
Illustration 3. Section B-B (refer to Illustration 1). Make sure that the collets, pins and all mating surfaces are clean before beginning the procedure.1. Position the bucket evenly over the lift arm bores.2. Insert approximately the same number of 103-1815 Shims 3.0 mm (.12 in) (15) and/or 103-1816 Shims (.20 in) (16) to both sides of the lift arm, to evenly space between the bucket and the lift arm (see Illustration 3). This procedure is to determine the necessary number of shims. Do not FORCE the shims into the space between the lift arm and the bucket bores.3. Remove the determined number of shims.4.

Caterpillar parts catalog:

Caterpillar parts catalog
TH350B Telehandler SLD00001-01640 (MACHINE) POWERED BY 3054E Engine
TH355B TH360B Telehandler JRK00001-UP (MACHINE) POWERED BY 3054E Engine
730 Ejector Articulated Truck B1W00001-UP (MACHINE) POWERED BY C11 Engine


Parts kit Caterpillar catalog:

3532207 KIT-ROD BEARING
206, 212, 3054, 3054B, 3054C, 307, 312, 312B L, 312C, 315, 315B L, 317, 414E, 416B, 416C, 416D, 416E, 420D, 420E, 422E, 424D, 426B, 426C, 428, 428B, 428C, 428E, 430D, 430E, 432E, 434E, 436C, 438C, 442...
3537429 KIT-BEARING
206, 212, 3054, 3054B, 307, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 426B, 426C, 428, 428B, 428C, 430D, 436C, 438C, 554, 908, 914G, AP-800C, BG-225C, CB-424, CB-434B, CB-434C, CB-5...
1288614 KIT-SEAL
120H, 120H ES, 120H NA, 135H, 135H NA, 216, 216B, 216B3, 226B, 226B3, 232B, 236, 236B, 236B3, 242B, 242B3, 246C, 247B, 247B3, 252B, 252B3, 256C, 257B, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C...
1214480 KIT-WATER BASE
120H, 120H ES, 120H NA, 135H, 135H NA, 216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 242B, 247, 247B, 247B3, 248, 257B, 267, 30/30, 301.5, 301.6C, 301.7D, 301.7D CR, 302.2D, 302.4D, 302.5, 302.5C, 30...
2720494 KIT-GASKET
3054C, 3054E, 315C, AP-300, AP-650B, AP-800D, C4.4, CB-434D, CB-534D, CB-564D, CD-54, CP-533E, CS-323C, CS-423E, CS-533E, M313C, M315C, PS-360C, TH210, TH215, TH220B, TH330B, TH340B, TH350B, TH355B, T...
2775156 KIT-GASKET
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 315C, 318D2 L, 414E, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 428D, 428E, 428F, 430D, 430E, 430F, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 4...
2333788 KIT-ROD BEARING
3054C, 3054E, 315C, 414E, 416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 432D, 432E, 434E, 442D, 914G, AP-650B, AP-800D, C4.4, CB-534D, CB-564D, CD-54, CP-433E, CS-433E, CS-533E, IT14G, M313C, ...
2310676 KIT-FLANGE
TH220B, TH330B, TH340B, TH350B, TH355B
1082148 KIT-SEAL
120M, 120M 2, 12M, 12M 2, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 24M, 568 FM LL, 824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 924K, 930K, 938F, 938G, 938G II, 938H, 938K, 950G, 950G I...
2385234 KIT-SEAL
TH220B, TH330B, TH340B, TH350B, TH355B
2015121 KIT-SHAFT
621H, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 770, 772, 773F, 775F, 777F, D250E II, D300E II, D350E II, D400E II
2392959 KIT-SEAL
TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2392956 KIT-SEAL
TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2153766 KIT-SEAL & NUT
432E, 434E, 442D, 442E, 444E, CB-22, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2528059 KIT-HORN
414E, 416E, 420E, 430E, 914G, 924G, 924GZ, 928G, 930G, 938G, IT14G, IT14G2, IT28G, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2385234 KIT-SEAL
TH220B, TH330B, TH340B, TH350B, TH355B
2271192 KIT-VALVE
420E, 430E, 432E, 434E, 442E, 444E, 450E, D5R LGP, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6N, D6N LGP, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2237885 KIT-SEAL
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2238061 KIT-CONTROL
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2238232 KIT-BEARING
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2331014 KIT-SEAL
TH220B, TH350B, TH355B, TH460B, TH560B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.