KIT-ENGINE GASKET 4605299 - Caterpillar

Illustration 1 g06143722
Connect to machine using Cat ET and verify that 1639-9 (Machine Security System Module: Abnormal Update Rate) code is active, and the Security System Tamper Resistant in PL641 become "Not Installed". Refer to Illustration 1, If not active but logged, and tamper level 2 is not lost, go to Step 11.
Access status screens through the Service Dashboard. Refer to Troubleshooting, UENR5824 , "Web Configuration Home Page".
a. If the radio cannot be accessed , then verify that radio is powered and operational.
b. If the connections are good but the radio is not operational, then replace PL641 radio and ECM with security library. Refer to ECM-replace in Troubleshooting, UENR0629 - C4.4 and C7.1 Engines, Troubleshooting, UENR5949C4.4 - 312D2 and 313D2 Excavators Machine System, Troubleshooting, UENR2724 - 374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit. Refer to Table 2 for ECM part numbers.
Table 2
Sales Model Prefix ECM Part Number Description of ECM
313D 2 S/N:FAP 386-3444 Machine ECM
313D 2GC S/N:GAP 386-3444 Machine ECM
318D 2L S/N:HBP 374-2640 Engine ECM
320D 2 S/N:ZBD 460-0132 Machine ECM
320D 2GC S/N:ZBH 374-2640 Engine ECM
323D 2L S/N:TDT 374-2640 Engine ECM
326D 2L S/N:XAM 374-2640 Engine ECM
330D 2L S/N:ZBF 374-2640 Engine ECM
336D 2 S/N:FAJ 372-2905 Engine ECM
336D 2GC S/N:FBT 372-2905 Engine ECM
336D 2L S/N:HBK 372-2905 Engine ECM
340D 2L S/N:JEE 372-2905 Engine ECM
374F S/N:NFJ 417-6020 Engine ECM
390F S/N:HJD 417-6020 Engine ECM
Verify a good cellular signal and provider connection using the Communication Check tool in the Service Dashboard.
Verify a good GPS signal on the GPS Status page through ET. If Cellular or GPS is not operational, verify that antenna is operational.
Replace any damaged components - Harness or antenna is necessary to restore operation.
Illustration 2 g06143724
Illustration 3 g06143726
Reset tamper level by Feature Protection System (FPS) process in CAT ET.
a. Access to ET, go to Configuration Tool page.
b. Set the Security System Tamper Resistant Configuration to Level 2. Refer to Illustration 2 and Illustration 3.
C. Access to the FPS request Web, then FPS will be generated. After input factory password, confirm to change, tamper level 2 will reset successful.
Key Switch OFF, wait 5 minutes, then key Switch ON.
Check for 1639-9 code whether disappear. If not repeat Step 8 and Step 9.
Illustration 4 g06143729
Update Product Link PL641 radio to 512-8575 Monitor Software Gp.
a. At ECM Summary page in ET, Click Utilities->Preferences->Modify.
b. Select "Communications", choose "Ethernet Direct Connection" and available drive. Refer to Illustration 4.Note: Intel(R) Ethernet Connection 1217-LM, Intel(R) Ethernet Connection 1217-V, Intel(R) Ethernet Connection 1218-LM, and Intel(R) 82579LM Gigabit Network Connection are optional.
Illustration 5 g06143731
Illustration 6 g06143735
Access to Winflash, flash 512-8575 Monitor Software Gp to PL641. Refer to Illustration 5 and Illustration 6.Note: Notice the warning message, do keep power to the ECM during flash process.