KIT-PISTON SEAL 4610643 - Caterpillar

4610643 KIT-PISTON SEAL Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4610643
461-0643
4610643

Weight: 0.13 pounds 0 kg.

Buy KIT-PISTON SEAL 4610643 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

4610643 Compatible with Seal Kit Compatible with CAT 305.5E2 Caterpillar Excavator Boom Cylinder Machinery Parts (CAT 305.5E2-CATERPILLAR)

$55.30

02 Sep 2025

CN: guangzhouguoshu

4610643 Compatible with Seal Kit Compatible with CAT 305.5E2 Caterpillar Excavator Boom Cylinder Machinery Parts (CAT 305.5E2-CATERPILLAR)
Generic 4610643 Compatible with Seal Kit Compatible with CAT 305.5E2 Caterpillar Excavator Boom Cylinder Machinery Parts

4610643 Seal kit Compatible with CAT 305.5E2 Compatible with Caterpillar Excavator Boom Cylinder Replacement (CAT 305.5E2)

$49.77

02 Sep 2025

CN: ExcavatorPro Pa

4610643 Seal kit Compatible with CAT 305.5E2 Compatible with Caterpillar Excavator Boom Cylinder Replacement (CAT 305.5E2)
Generic 4610643 seal kit Compatible with CAT 305.5E2 Compatible with Caterpillar excavator Boom cylinder Replacement

CARTEX Boom Cylinder Seal Kit 461-0642 461-0643 for FITS Caterpillar CAT Engine C2.4 Excavator 305E2CR 305E2

$79.98

23 Aug 2025

CA: High Quality Pa

CARTEX Boom Cylinder Seal Kit 461-0642 461-0643 for FITS Caterpillar CAT Engine C2.4 Excavator 305E2CR 305E2
CARTEX Whether you're a professional mechanic or a DIY enthusiast,We've got you covered with a wide range of parts that meet the highest standards of quality and performance. || Order your High Quality Part with peace of mind, knowing we prioritize your satisfaction. Quality Parts, Superior Performance - it's not just a promise, it's our standard || QUESTIONS? : We at CARTEX - High Quality Parts USA has more than 40 years of experience in industry and has in-house technicians, If you are not sure if this part fits your machine or tractor, just send us an email before you make the purchase and our in house technicians will revert back to you, right away.

Number on catalog scheme:

Caterpillar 4610643 Parts scheme KIT-PISTON SEAL

For full view, you need register

Information:

Illustration 5 g01241517
Typical view of the diagnostic connector from the wire side (A) Switched battery + (B) Battery ground (GND) (D) Data link + (E) Data link -
Disconnect the wires from pin A and pin B of the diagnostic connector.
If the diagnostic connector is mounted on the engine, perform the following steps:
Disconnect the wires from P2:56 and P2:64.
Fabricate a jumper wire in order to connect pin A of the diagnostic connector to P2:56.
Fabricate a jumper wire in order to connect pin B of the diagnostic connector to P2:64.
If the diagnostic connector is mounted off the engine, perform the following step:
Fabricate a jumper wire in order to connect pin "A" of the diagnostic connector to battery+ and pin "B" to the battery-.
Connect the electronic service tool to the diagnostic connector that is on the engine harness or on the application.
Turn the keyswitch to the ON position.Expected Result:The power lamp should illuminate on the communications adapter. The power lamp on the communications adapter may illuminate when the keyswitch is in any position.Results:
The power lamp is illuminated - The fault is in the harness.Repair: Repair the faulty harness or replace the faulty harness.Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.STOP
The power lamp is not illuminated. - Proceed to Test Step 6.Test Step 5. Check the Data Link Connections
Turn the keyswitch to the OFF position.
Disconnect the communications adapter from the diagnostic connector.
If the diagnostic connector is installed on the application, disconnect connector P1 from the ECM. Check the resistance between P1:20 and pin "D" on the diagnostic connector. If the diagnostic connector is installed on the engine, disconnect P2 from the ECM. Check the resistance between P2:47 and pin "D" on the diagnostic connector.
If the diagnostic connector is installed on the application, check the resistance between P1:28 and pin "E" on the diagnostic connector. If the diagnostic connector is installed on the engine, check the resistance between P2:55 and pin "E" on the diagnostic connector.Results:
The resistance is less than ten Ohms - Proceed to Test Step 6.
The resistance is greater than ten Ohms. - The fault is in the wiring harness or the connectorsRepair: Perform the following repair:Repair the connectors and/or the harness, or replace the connectors and/or the harness. Ensure that all of the seals are correctly in place and ensure that the connectors are correctly connected.Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.STOPTest Step 6. Change the Electronic Service Tool Components
If another electronic engine is available, connect the electronic service tool to the other engine. Ensure that the same cables are used.
Turn the keyswitch to the ON position. Determine if the electronic service tool operates correctly on the other engine.
If another engine is not available, obtain a replacement communications adapter and a replacement set of cables. Ensure that the cables for the electronic service tool are a complete set.
Install the replacement communications adapter