KIT-ELECTRIC MOTOR 4905487 - Caterpillar

Illustration 10 g02597530
(15) 9R-6307 Spacer (16) 3R-4353 (17) 6V-5842 Bolt (18) 3B-1915 Bolt (19) 129-3172 Mounting Stud (20) 180-4686 Bolt (21) 247-5712 Bracket As
Use the following procedure to install the mounting bracket (21) .
Install bracket (21), spacer (15), washer (16), and 3B-1915 Bolt (18). Hand tighten.
Install spacers (15), washers (16), and 129-3172 Mounting Studs (20). Hand tighten.
Install bolts to the air compressor.
Install spacer (15), washer (16), and 6V-5842 Bolt (17) to the top right pump hole. Torque completely.
Install spacer (15), washer (16), and 180-4686 Bolt (20) to the lower right pump hole. Torque completely.
Torque all remaining bolts and studs.
Illustration 11 g02597577
(22) Ladder clip (23) 5M-2894 Hard Washer (24) 9S-8752 Full Nut (25) 336-8613 Clip
Use a washer (23) and a nut (24) to install the ladder clip (22) on the top 129-3172 Mounting Stud
Use a washer (23) and a nut (24) to install the P-clip (25) to the bottom 129-3172 Mounting Stud. Position the clips as shown in IllustrationConfiguration of Low Mount Fuel Filters
Illustration 12 g02597640
Unclip the fuel hoses (1) .Remove the wire ties and p-clips (2) from the wire harness.
Illustration 13 g02597667
(3) 3B-1915 Bolt (4) 3E-4353 Hard Washer (5) 9R-6307 Spacer (6) 129-3172 Mounting Stud (7) 247-5712 Bracket As (8) P-clip
Use a bolt (3), washer (4), and a spacer (4) to install the bracket (7). Hand tighten.
Install a stud bolt (6) to the top right hole of the bracket. Hand tighten.
Thread a stud bolt (6) through the bottom right hole of the bracket and install the P-clip (8) .
Illustration 14 g02597760
(4) 3E-4353 Hard Washer (5) 9R-6307 Spacer (9) 6V-5842 Bolt (10) 180-4686 Bolt (11) 9S-8752 Full Nut (12) 5M-2894 Hard Washer
Use a washer (4) and a spacer (5) to install the bolt (9) to the top rear of the air compressor. Torque completely.
Use a washer (4) and a spacer (5) to install the bolt (10) on the bottom rear of the air compressor. Torque completely.
Use a nut (11) and a washer (12) to install a P-clip to the bracket. Torque completely.
Completely torque the remaining bolts.
Illustration 15 g02597960
(4) 3E-4353 Hard Washer (11) 9S-8752 Full Nut (12) 5M-2894 Hard Washer (13) 0S-1594 Bolt (14) 9L-6791 Bracket (15) 336-8613 Clip (16) 2Y-5829 Nut
Use the bolt (13), nut (11) and washer (12) to install the bracket (14) .
Attack a P-clip (15) to the bracket (14) .
Use the nut (16) and washer (4) to install a P-clip (15) .
Illustration 16 g02598357
Reposition the fuel fitting (17) and reattach the fuel line.