5253507 KIT-SEAL Caterpillar parts
Rating:
Alternative (cross code) number:
CA5253507
525-3507
5253507
CA5253507
525-3507
5253507
Weight: 0.75 pounds 0 kg.
Information:
Start By:a. remove turbochargerb. remove timing gear cover and oil pumpc. remove valve lifters 1. Remove the plug from the fuel injection pump housing, and install timing pin (A).2. While the crankshaft is turned clockwise (as seen from the front of the engine), push on Tool (A) until it slides into the groove (slot) in the fuel injection pump camshaft.3. Remove tachometer drive adapter shaft (1). 4. Install Tooling (B) into the camshaft drive gear for the fuel injection pump. Turn the center bolt until the drive gear is free of the shaft. Remove Tooling (B).
Typical Example5. Remove thrust pin (2) that holds the camshaft in place from the rear of the cylinder block. 6. Remove camshaft (3) and the gears from the cylinder block as a unit. Be careful not to cause damage to the camshaft bearings or camshaft lobes. The camshaft gear can be removed from the camshaft if a replacement is necessary.Install Camshaft & Gears
1. Install the camshaft gear on the camshaft if it was removed. Heat the gear to a maximum temperature of 315°C (600°F). Put the gear in position on the camshaft. 2. Put 4C-5593 Thread Lubricanton the camshaft lobes. Install camshaft (3) and the gears as a unit. Make sure the timing marks on the crankshaft gear and camshaft gear are in alignment.
Typical Example3. Install thrust pin (2). Tighten the pin to a torque of 48 7 N m (35 5 lb ft). 4. Put gear (4) in position, and install tachometer drive adapter shaft (1). Tighten the shaft to a torque of 150 14 N m (110 10 lb ft).5. Install the timing gear cover and oil pump. See the topic, "Remove & Install Timing Gear Cover & Oil Pump" in this manual.6. Install the valve lifters. See the topic, "Remove & Install Valve Lifters" in this manual. 7. After the valve lifters and timing gear cover have been installed, check the timing as follows:a. Remove timing pin (A).b.
Typical Example5. Remove thrust pin (2) that holds the camshaft in place from the rear of the cylinder block. 6. Remove camshaft (3) and the gears from the cylinder block as a unit. Be careful not to cause damage to the camshaft bearings or camshaft lobes. The camshaft gear can be removed from the camshaft if a replacement is necessary.Install Camshaft & Gears
1. Install the camshaft gear on the camshaft if it was removed. Heat the gear to a maximum temperature of 315°C (600°F). Put the gear in position on the camshaft. 2. Put 4C-5593 Thread Lubricanton the camshaft lobes. Install camshaft (3) and the gears as a unit. Make sure the timing marks on the crankshaft gear and camshaft gear are in alignment.
Typical Example3. Install thrust pin (2). Tighten the pin to a torque of 48 7 N m (35 5 lb ft). 4. Put gear (4) in position, and install tachometer drive adapter shaft (1). Tighten the shaft to a torque of 150 14 N m (110 10 lb ft).5. Install the timing gear cover and oil pump. See the topic, "Remove & Install Timing Gear Cover & Oil Pump" in this manual.6. Install the valve lifters. See the topic, "Remove & Install Valve Lifters" in this manual. 7. After the valve lifters and timing gear cover have been installed, check the timing as follows:a. Remove timing pin (A).b.
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
5205470
KIT-SEAL
Caterpillar
Caterpillar
5197969
KIT-SEAL
Caterpillar
Caterpillar
5197961
KIT-SEAL
Caterpillar
Caterpillar
5185139
KIT-SEAL
Caterpillar
Caterpillar
4937776
KIT-SEAL
Caterpillar
Caterpillar
4937770
KIT-SEAL
Caterpillar
Caterpillar
5332039
KIT-SEAL
Caterpillar
Caterpillar
5332038
KIT-SEAL
Caterpillar
Caterpillar
5332036
KIT-SEAL
Caterpillar
Caterpillar
5332034
KIT-SEAL
Caterpillar
Caterpillar
5332033
KIT-SEAL
Caterpillar
Caterpillar
5332023
KIT-SEAL
Caterpillar
Caterpillar