KIT-HARDWARE 5259969 - Caterpillar

Install hose and tube assembly (36) with o-ring seals (21) and leave the ends hand tight.
Install grommet (40), clip (39), clip (41), hard washer (38), and bolt (37) onto the hose and tube assembly. Tighten the hose and tube assembly and then the bolts for the clips.
Install hose assembly (35) from the fuel manifold to the fuel pump.
Illustration 16 g06050974
(42) 328-7088 Tube As
Install tube assembly (42) on the bottom of the fuel manifold.
Illustration 17 g06050969
(23) 228-7100 O-Ring Seal
(43) 330-9726 Plug As
(44) 241-6157 Plug
Install plug assembly (43) into the bottom of the fuel manifold and torque to 35 N m (26 lb ft).
Install plug (43) with o-ring seal (23) into the bottom of the fuel manifold and torque to 35 N m (26 lb ft).
Illustration 18 g06050999
(2) 228-7105 O-Ring Seals
(21) 228-7090 O-Ring Seals
(45) 281-5958 Connector
(46) 293-5016 Check Valve Gp
(47) 354-0014 Plug As
(48) 330-9724 Connector Plug As
Install two connector plug assemblies (48) in the fuel manifold and torque to 48 N m (35 lb ft).
Install check valve group (46) in the fuel manifold and torque to 48 N m (35 lb ft).
Install connector (45) with o-ring seal (2) and o-ring seal (21) in the fuel manifold and torque to 20 N m (15 lb ft).
Install plug assembly (47) in the fuel manifold and torque to 140 N m (103 lb ft).
Illustration 19 g06051013
(49) 382-4398 Hose As
Install two hose assemblies (49) onto the fuel manifold and torque the hose assemblies to 54 N m (40 lb ft).
Illustration 20 g06051041
(50) 416-4703 Fuel Priming Pump Gp
(51) 8T-0100 Bolt
(52) 9N-0869 Hard Washers
(53) 300-6714 Mounts
(54) 191-1782 Spacer
(55) 6V-3964 Hard Washer
(56) 143-4654 Bolt
(57) 8T-9655 Isolation Mount
(58) 191-1783 Spacer
Install fuel priming pump group (50) onto the engine.
Install two mounts (53), spacer (54), hard washer (52), hard washer (54), and bolt (51) into the top hole of the fuel priming pump group. Torque the bolt to 28 N m (21 lb ft).
Install four isolation mounts (57), two spacers (58), two hard washers (52), two hard washers (54), and two bolts (56) into the two bottom holes of the fuel priming pump group. Torque the bolts to 28 N m (21 lb ft).
Illustration 21 g06051075
(31) 6V-5839 Washers
(40) 6V-0826 Grommet
(59) 439-8607 Hose As
(60) 457-7752 Hose As
(61) 6V-1820 Bolt
(62) 8T-1887 Clips
(63) 8T-1888 Clips
(64) 6V-5843 Bolt
(65) 091-9035 Spacer
Install hose assembly (59) and hose assembly (60) from the fuel transfer pump to the fuel priming pump group. Leave the hose assemblies hand tight at the connections.
Install grommet (40), clip (62), clip (63), hard washer (31), and bolt (61) around hose assembly (59). Tighten the hose assembly connections to 110 N m (81 lb ft). Torque the bolt to 55 N m (41 lb ft).
Install grommet (40), clip (62), clip (63), hard washer (31), and bolt (64) around hose assembly (60). Tighten the hose assembly connections to 110 N m (81 lb ft). Torque the bolt to 55 N m (41 lb ft).