KIT-SEAL 5597577 - Caterpillar

5597577 KIT-SEAL Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA5597577
559-7577
5597577

Weight: 0.82 pounds 0 kg.

Buy KIT-SEAL 5597577 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

559-9854 5599854 559-7577 5597577 559-9856 5599856 559-7582 5597582 559-7590 5597590 559-9858 5599858 Compatible With 345GC CYL SEAL KIT (Oil)

$134.00

11 Apr 2025

HK: SHANDIEN

559-9854 5599854 559-7577 5597577 559-9856 5599856 559-7582 5597582 559-7590 5597590 559-9858 5599858 Compatible With 345GC CYL SEAL KIT (Oil)
Generic 559-9854 5599854 559-7577 5597577 559-9856 5599856 559-7582 5597582 559-7590 5597590 559-9858 5599858 || Compatible With 345GC CYL SEAL KIT

559-9854 5599854 559-7577 5597577 559-9856 5599856 559-7582 5597582 559-7590 5597590 559-9858 5599858 Compatible With 345GC CYL SEAL KIT (Hydraulic)

$87.00

07 Feb 2025

HK: SHANDIEN

559-9854 5599854 559-7577 5597577 559-9856 5599856 559-7582 5597582 559-7590 5597590 559-9858 5599858 Compatible With 345GC CYL SEAL KIT (Hydraulic)
Generic 559-9854 5599854 559-7577 5597577 559-9856 5599856 559-7582 5597582 559-7590 5597590 559-9858 5599858 || Compatible With 345GC CYL SEAL KIT

$87.00

17 Jan 2025

HK: SHANDIEN

Number on catalog scheme:

Caterpillar 5597577 Parts scheme KIT-SEAL

For full view, you need register

Information:

Start By:a. remove fuel lines 1. Remove plug (16) to allow Tool (B) to access the rack. 2. Install Tool (A). Remove twelve bushings (1) and twelve seals. 3. Install Tool (B) and (C). Make sure the flat end of Tool (B) is inserted.4. Remove twelve injection pumps (2) while pushing rack against Tool (B).
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
Be careful when the injection pumps are disassembled. Do not cause damage to the surface of the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump into the barrel of another pump. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
The following steps are for the installation of the fuel injection pumps.
Make sure the fuel racks are in the center "zero" position before the fuel injection pumps are installed.
5. Inspect parts of the injection pump and assemble. Plunger and barrel are a matched set.6. Install spring (9) on barrel (14) and washer (10) on plunger (11). Install plunger (11) in barrel (14). Install spring (12) and check valve (13) in bonnet (7). Install seal (6) on bonnet (7) and assemble bonnet assembly to plunger and barrel assembly with ring (8). 7. Install Tool (B) with flat end in and hold rack against Tool (B) in direction shown.8. Using Tool (C) install twelve injector pumps (2) as shown. Make sure slot in gear is in alignment with pin in lifter. 9. Install twelve O-ring seals (15) and twelve bushings (1). Use Tool (A) and torque to 163 14 N m (105 10 lb ft).
Check the rack movement (travel) with Tool (D) after each pump is installed. See the topic "Injection Pump Installation" in Systems Operation, Testing & Adjusting Manual, SENR5517.
If one or more of the injector pump have been installed wrong, damage to the engine is possible if cautions are not taken when the engine is first started. Make preparations to close off the air intake to stop the engine, if necessary.
End By:a. install fuel lines