AVSPARE.COM
parts catalog

KIT-MANIFOLD GASKET 6V3735 - Caterpillar


6V3735 KIT-MANIFOLD GASKET Caterpillar parts D379, D379B
Rating:
48
Alternative (cross code) number:
CA6V3735
6V-3735
6V3735
Caterpillar 6V3735 KIT-MANIFOLD GASKET
Weight: 1 pounds 0 kg.

Buy KIT-MANIFOLD GASKET 6V3735 Caterpillar genuine, new aftermarket tractor parts with delivery
GEN SET ENGINE, INDUSTRIAL ENGINE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$74.23
 

25 May 2019
200 Hundredths Pounds
CTP: CTP
6V3735 Group-Manifold Gasket Kit Fits Caterpillar
Warranty
  For full view, you need register

Compatible equipment models: 6V3735:

GEN SET ENGINE  D379B  
INDUSTRIAL ENGINE  D379   Caterpillar

Information:


Illustration 1 g03347646
Front view of the engine
Typical example
Illustration 2 g03347647
Marks for tightening main bearings
Typical example
Table 1
Item Qty Part Specification Description
The top face of the cylinder block, bottom surface of spacer plate (1) and both sides of plate gasket (2) must be free of fuel, oil, water, gasket adhesives, assembly compounds and any other contaminants during assembly.
1 2 225-3100 Spacer Plate Thickness is 8.585 0.025 mm (0.3380 0.0010 inch).
2 2 354-8484 Plate Gasket Apply adhesive to block side of gasket-plate only, no adhesive should be on opposing side of gasket-plate. Adhesive to be applied as an even, minimal coat(Skim coat). Minimal to zero material should squeeze out of joint after assembly has been torqued. No adhesive should contact water ferrule or liner lip.
Thickness of plate gasket that is between cylinder block and spacer plate is 0.20 0.02 mm (0.008 0.001 inch).
3 4 7C-9614 Taperlock Plug Before assembly, apply Loctite low breakloose PST on the threads.
Torque to 80 15 N m (60 11 lb ft).
A 4 4N-1650 Dowel Extension of the dowels on the left bank and right bank from the cylinder block is 18.5 0.5 mm (0.73 0.02 inch).
4 7 232-7607 Crankshaft Cap The crankshaft caps must be installed with the identifying marks toward the front of the engine. The number of the main bearing cap must also match the cast number on the left side of each main bearing saddle.
B - - Bore in cylinder block for main bearing is 129.891 0.013 mm (5.1138 0.0005 inch).
C - - The distance from the centerline of the crankshaft bearing bore to the top of the cylinder block is 419.10 0.15 mm (16.500 0.006 inch).
D - - The distance from the centerline of the crankshaft bearing bore to the bottom of the cylinder block is 165.10 0.10 mm (6.500 0.004 inch).
E - - The width of the slot for the crankshaft cap (4) is 236.00 0.05 mm (9.291 0.002 inch).
Width of crankshaft cap (4) is 235.500 0.025 mm (9.2716 0.0010 inch).
5 14 365-4307 Bolt Use the following procedure to install the crankshaft cap:
6 14 3P-1323 Bearing Cap Bolt
1. Apply clean engine oil on the threads of the bolts (6). Loosely install the bolts (6).
2. Apply clean engine oil on the threads of the side bearing cap bolts (5) and the washers. Loosely install the side bearing cap bolts (5) and the washers.
3. Tighten tab

Caterpillar parts catalog:

Caterpillar parts catalog
D379B GENERATOR SET ENGINE 34Z00001-UP
G398 & G399 Natural Gas Engine, D379, D398, And D399 Engines Overhaul And Maintenance Kits Only, For 6.25 Bore High & Low Compression Engine 34Z00001-UP
D379B ENGINE 68B02540-UP


Parts kit Caterpillar catalog:

6V3743 KIT-GASKET
D379, D379B, D398A, D398B, D399
8N4617 KIT-AIR CLEANER CLAMP
120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 235C, 30/30, 3116, 3126,...
3N3763 KIT-TERMINAL
1090, 1140, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673C, 1693, 16G, 16H NA, 16M, 215, 229...
6N7533 KIT-ROTOR VANE
3412, 772, 777, D348, D379B, G379, G399
5P8970 KIT-LINER GASKET
594H, D353C, D379, D379B, D398, D398A, D398B, D399, D9H
6V3749 KIT-GASKET
D379B, D398, D398B
6V3746 KIT-VALVE GRINDING GASKET
D379B, D398, D398A, D398B
6V3746 KIT-VALVE GRINDING GASKET
D379B, D398, D398A, D398B
6V3749 KIT-GASKET
D379B, D398, D398B
5P8970 KIT-LINER GASKET
594H, D353C, D379, D379B, D398, D398A, D398B, D399, D9H
3554378 KIT-CONNECTING PLUG
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 770G, 770G OEM, 772G, 772G OEM, 785D, 910K, 914K, 980M, C13, C15, C18, C32, C9.3, CX48...
3507575 KIT-SEAL
3512C, 3516C, TH55-E70, XQC1200
6V5465 KIT-GASKET
D379, D379B, D398
6V3741 KIT-GASKET
D379B, D398, D398A, D398B, D399
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.