KIT-GASKET 6V4744 - Caterpillar

REBE3759-01
15May2008
(Revised 10Jun2008)
U-260
A-212
TT-15
Before/After
PRODUCT SUPPORT PROGRAM FOR INSTALLING SOFTWARE ON CERTAIN C7 ENGINES INSTALLED IN GENERAL MOTORS CHASSIS
1920 1901 PS42698
This Program must be administered either before or after failure.In either case the decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS42698" as the Part Numberand "7755" as the Group Number. If administered before failure, use "56" as the Warranty Claim Description Code and "T" as the SIMS Description code.If administered after failure, use "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code.
The information supplied in this service letter may not be valid after the termination date of this program.Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.
This Revised Service Letter replaces the 15May2008 Service Letter. Changes have been made to Action Required to enable the exhaust brake warm up mode.
TERMINATION DATE
31May2010
PROBLEM
Updates to certain C7 software include enhanced diagnostic reporting, increased Caterpillar Regeneration System (CRS) robustness, and Turbocharger Exhaust brake strategy for Warm-up Mode.
AFFECTED PRODUCT
Model Identification Number
C7 C7S00514, 572, 581, 3949, 5176, 5197, 5211, 5215, 5217, 5239, 5473, 5475, 5478, 5483-5484, 5525, 5560, 5567, 5574, 5609-5610, 5612, 6269-6271, 6273, 6276, 6279, 6282, 6290, 6304, 6307, 6309, 6315, 6394, 6403, 6417, 6419-6422, 6429-6431, 6437, 6440
PARTS NEEDED
Qty
Part Number Description
1 3269115 SOFTWARE GP-ELEK
1 3269116 SOFTWARE GP-ELEK
1 3269117 SOFTWARE GP-ELEK
1 3269118 SOFTWARE GP-ELEK
1 3269119 SOFTWARE GP-ELEK
1 3269120 SOFTWARE GP-ELEK
1 3269121 SOFTWARE GP-ELEK
1 3269122 SOFTWARE GP-ELEK
1 3269123 SOFTWARE GP-ELEK
1 3269124 SOFTWARE GP-ELEK
ACTION REQUIRED
Determine the Electronic Control Module (ECM) Personality Module Part Number. If the ECM Personality Module Part Number currently installed on the truck is not the same as the Part Number listed on SISWeb, the truck must be flashed with the correct ECM Personality Module Part Number. After determining the correct ECM software to be flashed, download the correct Personality Module Software from SISWeb and save the software file on your service tool computer.
Using ET, connect to the engine ECM. Copy the current engine ECM Configuration. This will save the customer configuration and injector trim codes. Before copying the ECM Configuration, make sure the dashboard display in ET is disabled or the file may not copy injector trim files correctly.
To shut the dashboard display off, toggle the dashboard display button in the lower right hand corner of the active diagnostics or ECM summary windows in ET. The service tool dashboard should be red when disabled. Disconnect ET from the engine ECM by clicking on the disconnect button at the top of the ET screen and then reconnect.
In ET, click on the "Service" drop down menu and select "Configuration" then "Copy Configuration/ECM Replacement". Save this file to be used later in the procedure. Using the "Reset All" button, clear all Active Diagnostic Codes.
Connect to the ECM with "WinFlash". Select the latest Personality Module Software Part Number for your rating, begin the flashing process. After the flash process is complete reconnect with ET. Review the "Configuration" to ensure Injector trim files and other configurable parameters are correct. Other configuration parameters can be restored by uploading the ECM