7W6223 KIT-WATER PUMP Caterpillar parts
212, 428
Rating:
Alternative (cross code) number:
CA7W6223
7W-6223
7W6223
CA7W6223
7W-6223
7W6223
Weight: 2 pounds 1 kg.
BACKHOE LOADER, EXCAVATOR,
Number on catalog scheme:
None
For full view, you need register
Information:
Illustration 1 g02558730
Schematic of the Cat Data Link CircuitThis diagnostic code is recorded when the advisor does not receive expected information from the VIMS ECM. The possible causes of this diagnostic code are listed:
The wires for the Cat Data Link to the VIMS ECM are open or the wires are shorted.
The wrong software is installed on an ECM.Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS.
Verify that the following information is correct:
The part number of the flash software for the VIMS ECM
The part number of the flash software for the advisor
The part number of the VIMS ECM
The part number of the advisorNote: Consult your Caterpillar Dealer for the correct part numbers of the flash software.Expected Result:All of the part numbers are correct.Results:
OK - All of the part numbers are correct. Proceed to Test Step 2.
NOT OK - All of the part numbers are not correct. Repair: The installed VIMS ECM or the advisor have the wrong part number or the incorrect flash software is installed. Replace the VIMS ECM or replace the advisor that is incorrect. Replace the ECM with a module that has the correct part number. Flash the correct software. See Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program" for additional information.STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch to the OFF position.
Inspect all harness connections that are related to the Cat Data Link. Make sure that the connectors are clean and tight.
Check the connectors for proper mating. Ensure that all the seals are present and in place.
Check the harness for signs of damage or abrasion.
Check the wires at the connector. Ensure that the wires are secured tightly into the connector. Take care not to pull the wire out of the connector.
Check the exposed wires at the connectors for nicks or signs of abrasion.
Check for moisture inside the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and each socket of the machine harness connectors. Ensure that the contacts are properly installed. The contacts should mate correctly when the two pieces of the connector are placed together.Expected Result:The machine harness connectors are tight and free of corrosion.Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to Test Step 3.
NOT OK - The machine harness connectors are in need of repair.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK FOR SHORTS
The disconnect switch remains in the OFF position.
Disconnect the machine harness connectors from all electronic control modules that use the Cat Data Link.
At the harness connector for the advisor, measure the resistance between connector contact 8 (wire 893-GN) and all of the contacts that are used in the machine harness connector for the advisor. Perform the same measurements for connector contact 9 (wire 892-BR).Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each of the resistance measurements is greater than 5000 ohms. The harness circuit resistance is correct. Proceed to Test Step 4.
NOT OK - One of the resistance measurements
Caterpillar parts catalog:
Parts kit Caterpillar catalog:
206, 212, 3054, 3054B, 3054C, 307, 312, 312B L, 312C, 315, 315B L, 317, 414E, 416B, 416C, 416D, 416E, 420D, 420E, 422E, 424D, 426B, 426C, 428, 428B, 428C, 428E, 430D, 430E, 432E, 434E, 436C, 438C, 442...
206, 212, 3054, 3054B, 307, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 426B, 426C, 428, 428B, 428C, 430D, 436C, 438C, 554, 908, 914G, AP-800C, BG-225C, CB-424, CB-434B, CB-434C, CB-5...
206, 212, 3054, 3054B, 307, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 426B, 426C, 428, 428B, 428C, 430D, 436C, 438C, 554, 908, 914G, AP-800C, BG-225C, CB-424, CB-434B, CB-434C, CB-5...
212, 3054, 416B, 416C, 426C, 428, 428B, 428C, 436C, 438C, AP-800, AP-800C, BG-225B, CB-534B, CB-534C, CB-535B, CP-433C, CS-431C, PS-200B, PS-300B, RT50, TH103, TH62, TH63, TH82, TH83
416, 416B, 426, 426B, 428, 428B, 436, RT50
416, 416B, 426, 426B, 428, 428B, 436, RT50
30/30, 428, 5130, 65C, 75C, 75D, 85C, 85D, 918F, 924F, 928F, 928G, 928H, 928HZ, 938F, 938G, 938G II, 950F II, 966F II, 970F, 988F, 988F II, AP-1000, AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-9...
30/30, 428, 5130, 65C, 75C, 75D, 85C, 85D, 918F, 924F, 928G, 928H, 928HZ, 988F, 988F II, AP-1000, AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C, D4H, D4H ...
212, 428, AP-800, RT50, WE-601B
426, 428
416, 428
206, 212, 428
206, 3014
120G, 12G, 130G, 135H NA, 140G, 143H, 14G, 14H NA, 160H ES, 160H NA, 163H NA, 16G, 215, 215B, 225, 235, 235B, 245, 307, 312, 312B L, 315, 315B L, 317, 320B, 322 FM L, 322B L, 322B LN, 325B L, 330, 330...
120G, 1673C, 3304, 3306, 3306B, 518, 528, 815B, 920, 930, 966C, D4E
140B, 235, 3304, 3306, 637D, 941, 955L, D7G
7N6282
KIT-FUEL PRIMING KNOB
215, 641B, 777, 815B, 824B, 966D, AP-1000B, D342, D348, D8K, D9H
215, 641B, 777, 815B, 824B, 966D, AP-1000B, D342, D348, D8K, D9H
1673C, 1674, 235, 3306, 3406, 3408, 3412, 571G, 572G, 621R, 966D, 973, 977K, 980B, D379, D379A, D379B, D398B, D5, D6C, D7G
7T1369
KIT-BRUSH
120G, 12G, 130G, 140G, 14G, 160G, 16G, 428, 950F II, 953, 966F II, AP-1000, AP-1050, IT12B, PR-1000
120G, 12G, 130G, 140G, 14G, 160G, 16G, 428, 950F II, 953, 966F II, AP-1000, AP-1050, IT12B, PR-1000
426, 428, 436
416, 428
426, 428
3387791
KIT-GUARD
426, 428
426, 428
3412152
KIT-GUARD
426, 428
426, 428